Corrosion Characteristics of Ni-Based Hardfacing Alloy Deposited on Stainless Steel Substrate by Laser Cladding
Source abstract
Abstract
In this study, corrosion characteristics of a nickel-based Ni-Mo-Cr-Si hardfacing alloy having 32Mo, 15Cr, and 3Si (wt pct) as alloying elements, deposited on stainless steel SS316L substrate by laser cladding, have been presented. Corrosion behavior of the laser clad layer was evaluated in reducing (0.1 M HCl) and oxidizing (0.5 M HNO3) environments, in comparison with the reference substrate SS316L, using electrochemical potentiodynamic technique at room temperature. The corrosion mechanisms have been evaluated on the basis of microstructural and microchemical analysis using scanning electron microscopy attached with energy-dispersive spectrometry. Passivity behavior of the laser clad layer was studied in 0.5 M H2SO4, using the potentiostatic technique and analyzing the passive layer by X-ray photoelectron spectroscopy. Laser clad layer of Ni-Mo-Cr-Si exhibited higher pitting corrosion resistance in chloride (reducing) environment, indicated by much higher breakdown potential (~0.8 VSCE) and the absence of pitting as compared to substrate SS316L (~0.3 VSCE). However, in oxidizing (0.5 M HNO3) environment, both the laser clad layer and substrate SS316L showed excellent and similar corrosion resistance exhibiting high breakdown potential (~0.85 VSCE) and wide passivation range (~0.8 VSCE) with low passive current density (~4 to 7 × 10−6 A/cm2). The stable passive layer formed on laser clad layer of Ni-Mo-Cr-Si after exposure in 0.5 M H2SO4 solution at constant potential ~0.6 VSCE (within the passive range), consisted oxides of Mo as Mo+4 (MoO2) and Mo+6 (MoO4)−2, Cr as Cr3+ (mixture of both Cr2O3 and Cr (OH)3), and Si as Si4+(SiO2), which have contributed to passivation and repassivation and therefore excellent corrosion behavior.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. M. F. Ashby and D. R. H. Jones: An Introduction to Their Properties, 1 ST ed., Pergamon Press, Butterworth-Heinemann, Oxford, 1987.
2. F. A. Crane and J. A. Charles: Selection and Use of Engineering Materials, ., Butterworth-Heinemann, Oxford, 1997.
3. Z. A. Foroulis: Wear, 1984, vol. 96, pp. 203 -218.10.1016/0043-1648(84)90094-2 ↗
4. J. R. Davis: ASM Handbook, ASM International, Materials Park, OH, 2011, vol.6, pp 463-485.
5. D. Raghu and J. B. C. Wu: Materials Performance, 1997, vol. 36, No. 11, pp. 27-36.
6. Joseph R. Davis: Tool Materials, ASM Speciality Handbook, ASM International, 1995.
7. R. D. Schmidt and D. P. Ferriss: Wear, 1975, vol. 32, pp. 279– 289.10.1016/0043-1648(75)90316-6 ↗
8. J. R. Devis, Nickel, Cobalt, and Their Alloys, ASM Speciality Handbook, ASM International, Materials Park, OH, 2000.
9. J.J. Demo, D.P. Ferriss, Jr (1974) U.S. Patent, E. I. du Pont de Nemours and Company, Wilmington, DE, Patent No. 3,839,024.
10. A. Halstead and R. D. Rawlings: Mater. Sci., 1984, vol.18, No. 10, pp.491-500.
11. S. E. Mason and R. D. Rawlings: Mater. Sci. and Technol., 1989, vol. 5, pp.180-185.10.1179/mst.1989.5.2.180 ↗
12. R. Awasthi, S. Kumar, K. Chandra, B. Vishwanadh, R. Kishore, C. S. Viswanadham, D. Srivastava and G. K. Dey: Metal. and Mater.Trans. A, 2012, vol. 43, pp.4688-4702.10.1007/s11661-012-1290-6 ↗
13. E.I. Landerman, D.J. Boes, P. Bowen, M.J. Huck (1984) EPRI Report, EPRI NP-3446.
14. R. N. Johnson: Thin solid films, 1984, vol.118, pp. 31-47.10.1016/0040-6090(84)90104-4 ↗
15. G. Bolelli, L. Lusvarghi and R. Giovanardi: Surf. Coat. Technol., 2008, vol.202, pp. 4793–4809.10.1016/j.surfcoat.2008.04.056 ↗
16. G. Bolelli, L. Lusvarghi and M. Barletta: Surf. & Coat. Technol., 2008, vol. 202, pp. 4839–4847.10.1016/j.surfcoat.2008.04.074 ↗
17. R. N. Johnson and D.G. Farwick: Thin Solid Films, 1978, vol. 53, pp.365-373.10.1016/0040-6090(78)90229-8 ↗
18. D. G. Farwick and R. N. Johnson: Thin solid films, 1980, vol.73, pp.145-153.10.1016/0040-6090(80)90341-7 ↗
19. B. C. Oberlander and E. Lugscheider: Mat. Sci. and Technol., 1992, vol. 8, pp. 657-665.10.1179/mst.1992.8.8.657 ↗
20. P. J. E. Monson and W. M. Steen: Surf. Eng., 1990, vol. 6, pp.185–194.10.1179/sur.1990.6.3.185 ↗
21. Z.Y. Al-Taha. Ph. D. Thesis, Dublin City University, 2008.
22. M.M. Rakhes. Ph. D Thesis, The University of Manchester, 2013.
23. E. Toysarkani, A. Khajepour and S. F Corbin: Laser Cladding, CRC Press, Boca Raton, 2004.10.1201/9781420039177 ↗
24. S. D. Cramer, B.S. Covino: Corrosion: Fundamentals, Testing, and Protection ASM Handbook, ASM International, Materials Park, 2011.
25. N. Fairley: Casa XPS VAMAS Processing Software .
26. D. A. Shirley: Phys. Rev., 1972, vol. B5, pp. 4709.10.1103/PhysRevB.5.4709 ↗
27. C. R. Clayton and Y.C. Lu: J. Electrochem. Soc., 1986, vol. 133, No. 12, pp. 2465-2472.10.1149/1.2108451 ↗
28. Xiangrong Zhang, Dmitrij Zagidulin and David. W. Shoesmith: Electrochimica Acta, 2013, vol. 89, pp. 814-822.10.1016/j.electacta.2012.11.029 ↗
29. T. Hanawa, S. Hiromoto, A. Yamamoto, D. Kuroda and K. Asami: Mater. Trans., 2002, vol. 43, No 12, pp. 3088-3092.10.2320/matertrans.43.3088 ↗
30. R. Natarajan, N. Palaniswamy, M. Natesan and V. S. Muralidharan: The Open Corrosion Journal, 2009, vol. 2, pp. 114-124.10.2174/1876503300902010114 ↗
31. R. C. Newman: Corros. Sci., 1985, vol. 25, No 5, pp. 331-339.10.1016/0010-938X(85)90111-8 ↗
32. C. A. Lloyd, J. J. Noel, S. McIntyre and W. D. Shoesmith: Electrochimica Acta, 2004, vol. 49, pp. 3015–3027.10.1016/j.electacta.2004.01.061 ↗
33. J. R. Hayes, J. J. Gray, A. W. Szmodis and C. A. Orme: Corrosion Science, 2006, vol. 62, No. 6, pp. 491-500.10.5006/1.3279907 ↗
34. J. G. Choi and L. T. Thompson: Applied Surf. Sci., 1996, vol. 93, pp. 143-149.10.1016/0169-4332(95)00317-7 ↗
35. A. Thogersen, J. H. Selj and E. S. Marstein: J. Electrochem. Soc., 2012, vol. 159, No. 5, pp. 276-281.10.1149/2.jes113659 ↗
36. C. H. F. Peden, J. W. Rogers, N. D. S. Jr., K. B. Kidd and K. L. Tsang: Phys. Rev. B,1993, vol. 47, pp. 1993.10.1103/PhysRevB.47.15622 ↗
37. F. Himpsel, F. McFeeley, A. Taleb-Ibrahimi, J. Yarmoand, G. Hollinger: Phys. Rev. B, 1988, vol. 38, pp. 6084.10.1103/PhysRevB.38.6084 ↗
38. J. R. Davis: ASM handbook, ASM, Materials park, OH, 1992, Vol..6, pp.861-872.
39. A. Halstead and R. D. Rawlings: Journal of Mat. Sci., 1985, vol. 20, pp.1248-1256.10.1007/BF01026320 ↗
40. W. Xu, R. Liu, P. C. Patnaik, M. X. Yao and X. J. Wu: Mat. Sci. and Eng. A, 2007, vol. 405, pp. 427-436.10.1016/j.msea.2006.10.088 ↗
41. K. Komvopoulos and K. Nagarathnam: J. of Engineering Mater. and Technol., 1990, vol.112, pp. 131-143.10.1115/1.2903299 ↗
42. R. Jendrzejewski, G. Sliwinski, M. Krawczuk and W. Ostachowicz: Computers and Structures, 2004, vol. 82, pp. 653–658.10.1016/j.compstruc.2003.11.005 ↗
43. I.H. Toor, J.Y. Kwon, and H.S. Kwon: Journal of The Electrochemical Society, 2008, vol. 155, No. 9, pp.495-500.10.1149/1.2953522 ↗
44. F. H. Scott, G. C. Wood, and J. Stringer: Oxid. Met., 1995, vol. 113, pp. 145.
45. S. N. Basu and G. J. Yurck: Oxid. Met., 1991, vol. 281, pp. 315.
46. D. Zhang, S. J. Harris and D. G. McCartney: Mater. Sci. Eng. A, 2003, vol.344, pp. 45-56.10.1016/S0921-5093(02)00420-3 ↗
47. W. M. Zhao, Y. Wang, L. X. Dong, K. Y. Wu and J. Xue: Surf. Coat. Technol., 2005, vol. 190, pp. 293-298.10.1016/j.surfcoat.2004.04.057 ↗