journal article·2018-02

Impact of Martensite Spatial Distribution on Quasi-Static and Dynamic Deformation Behavior of Dual-Phase Steel

Manpreet Singh, Anindya Das, T. Venugopalan, Krishnendu Mukherjee, Mahesh Walunj, Tarun Nanda, B. Ravi Kumar

Publisher page

Abstract

The effects of microstructure parameters of dual-phase steels on tensile high strain dynamic deformation characteristic were examined in this study. Cold-rolled steel sheets were annealed using three different annealing process parameters to obtain three different dual-phase microstructures of varied ferrite and martensite phase fraction. The volume fraction of martensite obtained in two of the steels was near identical (~ 19 pct) with a subtle difference in its spatial distribution. In the first microstructure variant, martensite was mostly found to be situated at ferrite grain boundaries and in the second variant, in addition to at grain boundaries, in-grain martensite was also observed. The third microstructure was very different from the above two with respect to martensite volume fraction (~ 67 pct) and its morphology. In this case, martensite packets were surrounded by a three-dimensional ferrite network giving an appearance of core and shell type microstructure. All the three steels were tensile deformed at strain rates ranging from 2.7 × 10−4 (quasi-static) to 650 s−1 (dynamic range). Field-emission scanning electron microscope was used to characterize the starting as well as post-tensile deformed microstructures. Dual-phase steel consisting of small martensite volume fraction (~ 19 pct), irrespective of its spatial distribution, demonstrated high strain rate sensitivity and on the other hand, steel with large martensite volume fraction (~ 67 pct) displayed a very little strain rate sensitivity. Interestingly, total elongation was found to increase with increasing strain rate in the dynamic regime for steel with core–shell type of microstructure containing large martensite volume fraction. The observed enhancement in plasticity in dynamic regime was attributed to adiabatic heating of specimen. To understand the evolving damage mechanism, the fracture surface and the vicinity of fracture ends were studied in all the three dual-phase steels.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. D. K. Mondal and R.M. Dey: Mater. Sci. Eng. A, 1992, vol. 149, pp. 173–81.10.1016/0921-5093(92)90378-E ↗
2. Y. Cao, J. Ahlström, and B. Karlsson: J. Mater. Res. Technol., 2015, vol. 4, pp. 68–74.10.1016/j.jmrt.2014.11.001 ↗
3. G. R. Speich: Fundamentals of Dual Phase Steels, Chicago, USA, 1981, pp. 3–46.
4. R. G. Davies: Metall. Trans. A, 1978, vol. 9, pp. 671–679.10.1007/BF02659924 ↗
5. L. Wannman and A. Melander, Mater. Des.,1991, vol. 12 (3), pp. 129–132.10.1016/0261-3069(91)90120-S ↗
6. R.A. Mohammad and A. Ekrami: Mater. Sci. Eng. A, 2008, vol. 477, pp. 306–10.10.1016/j.msea.2007.05.051 ↗
7. L. V. D. L. Concepción, N. H. Lorusso, and G.H. Svobod: Procedia Mater. Sci., 2015, vol. 8, pp. 1047–56.10.1016/j.mspro.2015.04.167 ↗
8. Z. Jiang, Z. Guan and J. Lian: Mater. Sci. Eng. A., 1995, vol. 190, pp. 55–64.10.1016/0921-5093(94)09594-M ↗
9. V. Singh, M. Adhikary, T. Venugopalan, A. Chakraborty, T. Nanda, and B. Ravi Kumar: Mater. Manuf. Process., https://doi.org/10.1080/10426914.2017.1317792.10.1080/10426914.2017.1317792 ↗
10. A. Chakraborty, M. Adhikary, T.Venugopalan, V. Singh, T. Nanda, and B. Ravi Kumar: Mater. Sci. Eng. A, 2016, vol. 676, pp. 463–73.10.1016/j.msea.2016.09.018 ↗
11. M. Erdogan and S. Tekeli: Mater. Charact., 2002, vol. 49, pp. 445–54.10.1016/S1044-5803(03)00070-6 ↗
12. X. Sun, K.S. Choi, A. Soulami, W.N. Liu and M.A. Khaleel: Mater. Sci. Eng. A, 2009, vol. 526, pp. 140–149.10.1016/j.msea.2009.08.010 ↗
13. N.J. Kim and G. Thomas: Metall. Trans. A., 1981, vol. 12, pp. 483–489.10.1007/BF02648546 ↗
14. X. J. He, N. Terao, and A. Berghezan: Met. Sci., 1984, vol. 18, pp. 367–73.10.1179/030634584790419953 ↗
15. J. Zhang, D. Hongshuang, Y. Deng, and R. D. K. Misra: Mater. Sci. Eng. A, 2015, vol. 627, pp. 230–40.10.1016/j.msea.2015.01.006 ↗
16. B. Ravi Kumar, N. K. Patel, K. Mukherjee, M. Walunj, G. K. Mandal, and T. Venugopalan: Mater. Sci. Eng. A, 2017, vol. 685, pp. 187–93.10.1016/j.msea.2017.01.007 ↗
17. W. Wang, M. Li, C. He, X.Wei, D. Wang, and H. Du: Mater. Des., 2013, vol. 47, pp. 510–21.10.1016/j.matdes.2012.12.068 ↗
18. S. Oliver, T.B. Jones and G. Fourlaris: Mater. Sci. Tech., 2007, vol. 23 (4), pp. 423–431.10.1179/174328407X168937 ↗
19. S. Oliver, T.B. Jones and G. Fourlaris: Mater. Charact., 2007, vol. 58 (4), pp. 390–400.10.1016/j.matchar.2006.07.004 ↗
20. H. Huh, S.B. Kim, J.H. Song and J.H. Lim: Int. J. Mech. Sci., 2008, vol. 50 (5), pp. 918–931.10.1016/j.ijmecsci.2007.09.004 ↗
21. N. D. Beynon, T. B.Jones, and G. Fourlaris: Mater. Sci. Technol., 2005, vol. 21, pp. 103–12.10.1179/174328405X16234 ↗
22. A. Das, M. Ghosh, S. Tarafder, S. Sivaprasad, and D. Chakrabarti: Mater. Sci. Eng. A, 2017, vol. 680, pp. 249–58.10.1016/j.msea.2016.10.101 ↗
23. ASTM, E-8M: Standard Test Methods for Tension Testing of Metallic Materials [Metric], 1997.
24. P. K. C. Wood and C. A. Schley: Strain Rate Testing of Metallic Materials and Their Modelling for use in CAE Based Automotive Crash Simulation Tools (Recommendations and Procedures), Smithers Publishers, 2009.
25. ISO 26203-2: Metallic Materials - Tensile Testing at High Strain Rates - Part 2: Servohydraulic and Other Test Systems, International Standard, 2011.
26. S. K. Paul, A. Raj, P. Biswas, G. Manikandan and R.K. Verma: Mater. and Des., 2014, vol. 57, pp. 211-217.10.1016/j.matdes.2013.12.047 ↗
27. A. Uenishi and C. Teodosiu: Acta Mater., 2003, vol. 51, pp. 4437-4446.10.1016/S1359-6454(03)00279-9 ↗
28. A. Bardelcik, C. P. Salisbury, S. Winkler, M. A. Wells and M. J. Worswick: Int. J. Impact Eng., 2010, vol. 37, pp. 694-702.10.1016/j.ijimpeng.2009.05.009 ↗
29. A. Bag, K.K. Ray, E.S. Dwarakadasa: Metall. Mater. Trans. A., 1999, vol. 30, pp. 1193–1202.10.1007/s11661-999-0269-4 ↗
30. C.H. Crussard and B. Jaoul: Rev. Metall., 1950, vol. 42, pp. 589–600.10.1051/metal/195047080589 ↗
31. A. G. Kalashami, A. Kermanpur, E. Ghassemali, A. Najafizadeh, and Y. Mazaheri: Mater. Sci. Eng. A, 2016, vol. 678, pp. 215–26.10.1016/j.msea.2016.09.108 ↗
32. Y. Bergstrom, Y. Granbom, and D. Sterkenburg: J. Metall., 2010, https://doi.org/10.1155/2010/647198.10.1155/2010/647198 ↗
33. H. Ashrafi, M. Shamanian, R. Emadi, and N. Saeidi: Trans. Indian Inst. Met., 2017, vol. 70(6), pp. 1575-1584.10.1007/s12666-016-0955-z ↗