journal article·2012-09

Evolution of Precipitate Phases During Long-Term Isothermal Aging at 1083 K (810 °C) in a New Precipitation-Strengthened Heat-Resistant Austenitic Stainless Steel

Vu The Ha, Woo Sang Jung

Publisher page

Abstract

Evolution of precipitate phases in a precipitation-strengthened high nitrogen 15Cr-15Ni-4Mn-3Cu-1.5Mo-0.46Si-Nb-C-N-Al-B austenitic heat-resistant stainless steel during 10,000 hours of isothermal aging at 1083 K (810 °C) was investigated. The major precipitate phases found in microstructure after 330 hours of aging are coarser residual primary Nb(C,N) precipitates, Z-phase precipitates, (Nb,Cr)N precipitates with fcc crystal structure, Cu precipitates, and coarser Cr2N precipitates. No significant changes were noted in the chemical compositions, crystal structure of the precipitate phases, or the phase species after 10,000 hours at 1083 K (810 °C). The coarsening behavior of Z-phase, (Nb,Cr)N, and Cu precipitates was the only observed notable change in the microstructures during the performed aging. Z-phase and (Nb,Cr)N precipitates exhibited superior dimensional stability and morphology with extremely low coarsening rates, while Cu precipitates coarsened at the fastest rate. In addition, Z-phase particles showed a remarkable lower coarsening rate as compared to that of (Nb,Cr)N precipitates. The abnormal slow coarsening kinetics of Z-phase can be explained by the nucleation energy barrier (NEB) limited coarsening mechanism applied for faceted ceramic crystals.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. R. Wiswanathan, K. Coleman, and U. Rao: Int. J. Pressure Vess. Pip., 2006, vol. 83, pp. 778–83.10.1016/j.ijpvp.2006.08.006 ↗
2. T. Sourmail: Ph.D. Thesis, University of Cambridge, London, 2001, pp. 12–26.
3. M.P. Brady, Y. Yamamoto, M.L. Santella, P.J. Maziasz, B.A. Pint, C.T. Liu, Z.P. Lu, and H. Bei: JOM, 2008, vol. 60 (7), pp. 12–18.10.1007/s11837-008-0083-2 ↗
4. J.P. Shingledecker, P.J. Maziasz, N.D. Evans, and M.J. Pollard: Int. J. Pressure Vess. Pip., 2007, vol. 84, pp. 21–28.10.1016/j.ijpvp.2006.09.014 ↗
5. R. Rautio and S. Bruce: “Sandwik Sanicro 25, A New Material for Ultrasupercritical Coal Fired Boilers,” Technical Article, Sandvik Material Technology, Sandviken Sweden, 2004.10.31399/asm.cp.am-epri-2004p0274 ↗
6. P.J. Maziasz and B.A. Pint: J. Eng. Gas Turbines Power, 2011, vol. 133, pp. 0921021–0921025.10.1115/1.4002828 ↗
7. V.T. Ha, W.S. Jung, and J.Y. Suh: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3378–85.10.1007/s11661-011-0752-6 ↗
8. D.R.G. Mitchell and S. Sulaiman: Mater. Charact., 2006, vol. 56, pp. 49–58.10.1016/j.matchar.2005.09.004 ↗
9. http://matcalc.tuwien.ac.at/
10. M. Tendo, Y. Tadokoro, K. Suetsugu, and T. Nakazawa: ISIJ Int., 2001, vol. 41 (3), pp. 262–67.10.2355/isijinternational.41.262 ↗
11. N. Maruyama and G.D.W. Smith: Mater. Sci. Eng. A, 2002, vol. 327, pp. 34–39.10.1016/S0921-5093(01)01889-5 ↗
12. S. Vervynct, K. Verbeken, P. Thibaux, M. Liebeherr, and Y. Houbaert: ISIJ Int., 2009, vol. 49 (6), pp. 911–20.10.2355/isijinternational.49.911 ↗
13. P. Marshall: Austenitic Stainless Steels: Microstructure and Mechanical Properties, Elsevier Applied Science, London, 1984, p. 23.
14. W. Truszkowski, J. Krol, and B. Major: Metall. Mater. Trans. A, 1980, vol. 11A, pp. 749–58.10.1007/BF02661204 ↗
15. C. Kocer, T. Abe, and A. Soon: Mater. Sci. Eng. A, 2009, vol. 505, pp. 1–5.10.1016/j.msea.2008.10.028 ↗
16. H. Ono-Hakazato, K. Taguchi, K. Tamura, Y. Tomatsu, and T. Usui: Metall. Mater. Trans. B, 2001, vol. 32B, pp. 1113–18.10.1007/s11663-001-0099-2 ↗
17. V. Vodarek: Mater. Sci. Eng. A, 2011, vol. 528, pp. 4232–38.10.1016/j.msea.2011.02.025 ↗
18. H.K. Danielsen, J. Hald, F.B. Grumsen, and M.A.J. Somers: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2633–40.10.1007/BF02586098 ↗
19. J.P. Adamson and J.W. Martin: Metallography, 1975, vol. 8, pp. 169–76.10.1016/0026-0800(75)90053-1 ↗
20. Q. Wu: Ph.D. Thesis, University of Cincinnati, Cincinnati, OH, 2006, pp. 100–155.
21. I.M. Lifshitz and V.V. Slyozov: J. Phys. Chem. Sol., 1961, vol. 19, pp. 35–50.10.1016/0022-3697(61)90054-3 ↗
22. C. Wagner: Z. Electrochem., 1961, vol. 65, pp. 581–91.
23. A.J. Ardell and V. Ozolins: Nat. Mater., 2005, vol. 4, pp. 309–16.10.1038/nmat1340 ↗
24. G.J. Shiflet, H.I. Aaronson, and T.H. Courtney: Acta Metall., 1978, vol. 27, pp. 377–85.10.1016/0001-6160(79)90030-0 ↗
25. G.S. Rohrer, C.L. Rohrer, and W. Mullins: J. Am. Ceram. Soc., 2002, vol. 85 (3), pp. 675–82.10.1111/j.1151-2916.2002.tb00149.x ↗
26. A. Gustafson: Mater. Sci. Eng. A, 2000, vol. 287, pp. 52–58.10.1016/S0921-5093(00)00827-3 ↗
27. B. Peng, H. Zhang, J. Hong, J. Gao, H. Zhang, J. Li, and Q. Wang: Mater. Sci. Eng. A, 2010, vol. 527, pp. 4424–30.10.1016/j.msea.2010.03.089 ↗
28. J. Erneman, M. Schwind, H.-O. Andren, J.-O. Nilsson, A. Wilson, and J. Agren: Acta Mater., 2006, vol. 54, pp. 67–76.
29. M. Fujita and H.K.D.H. Bhadeshia: Mater. Sci. Technol., 2001, vol. 17, pp. 403–08.10.1179/026708301101510122 ↗
30. Y.N. Chentsov: Met. Sci. Heat Treat., 1981, vol. 23 (1), pp. 69–72.10.1007/BF00700310 ↗
31. D. Wanatabe, C. Wanatabe, and R. Monzen: J. Mater. Sci., 2008, vol. 43, pp. 3946–53.10.1007/s10853-007-2373-4 ↗
32. B. Dutta, E. Valdes, and C.M. Sellars: Acta Metall. Mater., 1992, vol. 40 (4), pp. 653–62.10.1016/0956-7151(92)90006-Z ↗
33. J. Kučera and K. Stránský: Mater. Sci. Eng., 1982, vol. 52, pp. 1–38.10.1016/0025-5416(82)90067-2 ↗