Effect of Microstructure on Creep Crack Growth Behavior of a Near-α Titanium Alloy IMI-834
Source abstract
Abstract
In the present study, the effect of microstructure (i.e., α + β and transformed β) on creep crack growth (CCG) behavior of a near-alpha (IMI 834) titanium alloy has been explored at temperatures 550 °C and 600 °C. For characterizing the CCG behavior of the alloy, both stress intensity factor (K) and energy integral parameter (Ct) were used in the present investigation. The use of stress intensity factor (K) as crack-tip parameter is not appropriate in the present study as no unique correlation between crack growth rate and K could be obtained from the observed trend due to transients in the creep crack rate data. On the other hand, Ct parameter for both microstructural conditions consolidates CCG data into a single trend. The alloy with fully transformed β microstructure exhibits better CCG resistance as compared to bimodal (α + β) microstructure. This is consistent with the fact that the transformed β structure offers superior creep resistance as compared to α + β microstructure. Microstructural examination has revealed that CCG for both microstructural conditions is accompanied by formation of damage zone in the form of numerous environmental-assisted secondary surface cracks (perpendicular to the stress axis) ahead of the main crack tip. For α + β microstructure of the alloy, the surface creep cracks were formed by growth and coalescence of microcracks nucleated by fracture of primary α particles. While in the interior of the specimens, CCG occurred by growth and coalescence of microvoids nucleated at primary α/transformed β (matrix) interfaces. For β microstructure of the alloy, while the surface creep cracks formed by growth and coalescence of microvoids nucleated at titanium enriched surface oxide particles, in the interior CCG occurred by nucleation of intergranular cavities.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. G. Nagalakshmi and V. Kumar: DMRL TR 2005371, DMRL, Hyderabad, 2005
2. Standard Test Method for Measurement of Creep Crack Growth Rates in Metals, ASTM E 1457-00, ASTM, Philadelphia, PA, vol. 03.01, 1995, pp. 960–74
3. Evaluation of C t Parameter for Characterizing CCGR in the Transient Regime, ASTM STP 905, John L. Bassani, Donald E. Hawk, and Ashok Saxena, eds., ASTM, Philadelphia, PA, 1989, pp. 7–2610.1520/STP26768S ↗
4. Evaluation of C* for the Characterizing of Creep-Crack-Growth Behavior in 304 Stainless Steel, ASTM STP 700, A. Saxena, ed., ASTM, Philadelphia, PA, 1980, pp. 131–5110.1520/STP36968S ↗
5. A. Saxena, H.A. Ernst, J.D. Landes: Int. J. Fract., 1983, vol. 23, pp. 245–5710.1007/BF00020693 ↗
6. H. Riedel, V. Detampel: Int. J. Fract., 1987, vol. 33, pp. 239–6210.1007/BF00044414 ↗
7. K.M. Nikbin: Int. J. Press. Vess. Pip., 2003, vol. 80 (7–8), pp. 415–1610.1016/S0308-0161(03)00095-4 ↗
8. K. Sadanada, P. Shahinian: Eng. Fract. Mech., 1981, vol. 15 (3–4), pp. 327–4010.1016/0013-7944(81)90064-3 ↗
9. S.H. Ryu, Jinyu, S.H. Hong: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 629–3410.1007/s11661-997-0048-z ↗
10. T. Hollsteir and B. Voss: ASTM STP 995, ASTM, Philadelphia, PA, pp. 195–213
11. S. Xu, A.K. Koul, J.I. Dickson: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 795–80410.1007/s11661-001-0095-9 ↗
12. M. Tabuchi, K. Kabu, K. Yagi, A.T. Yokobori, and A. Fuji: Eng. Fract. Mech., 1999, vol. 62, pp. 47–6010.1016/S0013-7944(98)00082-4 ↗
13. B. Dogan, A. Saxena, K.H. Schwalbe: Mater. High Temp., 1992, vol. 10 (2), pp. 138–4310.1080/09603409.1992.11689411 ↗
14. B. Dogan and K.H. Schwalbe, Creep Crack Growth Behavior of Titanium Alloy, Fracture Mechanics: 22nd Symp., ASTM STP 1131, H.A. Ernst, A. Saxena, and D.L. McDowell, eds., ASTM, Philadelphia, PA, 1992, vol. I, pp. 284–96
15. R.H. Norris, A. Saxena, J. Tucker: Eng. Fract. Mech., 1999, vol. 62, pp. 79–9710.1016/S0013-7944(98)00086-1 ↗
16. A. Saxena: Non-Linear Fracture Mechanics for Engineers, CRC Press, Boca Raton, FL, 1998, pp. 309–62
17. Y. Murakami: Handbook of Stress Intensity Factors, Pergamon Press, Headington Hill Hall, Oxford, England, 1987, vol. 1, pp. 9–10
18. H. Riedel, J.R. Rice: Fracture Mechanics: 12th Conf., ASTM STP 700, ASTM, Philadelphia, PA, 1980, pp. 112–3010.1520/STP36967S ↗
19. K. Ohji, K. Ogura, and S. Kubo: JSME, 1979, No. 790-13, pp. 18–20 (in Japanese)
20. A. Saxena: Eng. Fract. Mech., 1991, vol. 40, pp. 721–3610.1016/0013-7944(91)90231-O ↗
21. J.L. Bassani, D.E. Hawk, and A. Saxena: Non-Linear Fracture Mechanics: Time Dependent Fracture Mechanics, ASTM, STP 995, Philadelphia, PA, 1989, vol. I, pp. 7–29
22. D.V.V. Satyanarayana, T. Sridhar, B. Narsingh Rao, G.B. Vikram, Ch. Swarnakumari, and Vikas Kumar: DMRL TR 2005380, DMRL, Hyderabad, Aug. 2005
23. M.Es. Souni: Mater. Charact., 2001, vol. 46, pp. 365–7910.1016/S1044-5803(01)00136-X ↗