Creep Properties of the As-Cast Al-A319 Alloy: T4 and T7 Heat Treatment Effects
Source abstract
Abstract
In this work, the creep behavior of a commercial Al-A319 alloy was investigated in the temperature range of 413 K to 533 K (140 °C to 260 °C). Tensile creep specimens in the as-cast condition and after heat treating by solid solution (T4) and by aging (T7) were tested in a stress range varying from 60 to 170 MPa. It was found that steady-state creep strain rate was significantly low in the T7 condition when compared with either the T4 or as-cast alloy conditions. As a result, the time to failure behavior considerably increased. The experimentally determined creep exponents measured from the stress–strain curves were 4 for the as-cast alloy, 7.5 in the solid solution, and 9.5 after aging. In particular, after solid solution a grain substructure was found to develop which indicated that creep in a constant subgrain structure was active, thus accounting for the n exponent of 7.5. In the aged condition, a stress threshold is considered to account for the power law creep exponent n of 9.5. Moreover, It was found that the creep activation energy values were rather similar for the alloys in the as-cast (134 kJ/mol) and T4 (146 kJ/mol) conditions. These values are close to the one corresponding to pure Al self-diffusion (143 kJ/mol). In the aged alloy, the apparent creep activation energy (202 kJ/mol) exceeded that corresponding to Al self-diffusion. This deviation in activation energy is attributed to the effect of temperature on the alloy elastic modulus. Microstructural observations using transmission electron microscopy provided further support for the various dislocation-microstructure interactions exhibited by the alloy under the investigated creep conditions and implemented heat treatments.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. Z. Li, A.M. Samuel, F.H. Samuel, C. Ravindran, S. Valtierra, H.W. Doty: Mater.Sci. Eng. A, 2004, 367, 96–110.10.1016/j.msea.2003.09.090 ↗
2. T.L. Reinhart: ASM Handbook, Vol 19, Fatigue and Fracture, ASM International, Materials Park, OH, 1996.
3. F.J. Feikuy: AFS Trans., 1998, 61, 225–31.
4. C.H. Cáceres, C.J. Davidson, J.R. Griffiths: Mater.Sci. Eng. A, 1995, 197, 171–9.10.1016/0921-5093(94)09775-5 ↗
5. C.H. Caceres, L. Stensson, J.A. Taylor: Int. J. Cast metals Res., 2003, 15, 531–43.10.1080/13640461.2003.11819539 ↗
6. Q.G. Wang, D. Apelian, D.A. Lados: J. Light. Met., 2001, 1, 73–84.10.1016/S1471-5317(00)00008-0 ↗
7. S. Haro, J. Ramírez, D.K. Dwivedi, E. Martínez: Materials Science and Technology, 2009, 25, 886–91.10.1179/174328408X327722 ↗
8. Z. Ma, A.M. Samuel, F.H. Samuel, H.W. Doty, S. Valtierra: Mats. Sci. & Eng. A, 2008, 490, 36–51.10.1016/j.msea.2008.01.028 ↗
9. H.R. Erfanian-Naziftoosi, N. Haghdadi, A.R. Kiani-Rashid: Journal of Materials Engineering and Performance, 2011, 21, 1785–1792.10.1007/s11665-011-0086-y ↗
10. D. D. Tian, X.S. Liu, C. Q. He, Y. Shen, S.Q. Lv and Q. C. Wang, Mats. Sci. & Eng. A, 2016, 654, pp. 60–80.10.1016/j.msea.2015.12.023 ↗
11. C. Ravi, C. Wolverton: Acta Mater., 2004, 52, 4213–27.10.1016/j.actamat.2004.05.037 ↗
12. A.R. Farkoosh, X. Grant Chen, M. Pekguleryuz: Materials Science and Engineering: A, 2015, 627, 127–38.10.1016/j.msea.2014.12.115 ↗
13. E. Gariboldi, F. Casaro: Materials Science and Engineering: A, 2007, 462, 384-388.10.1016/j.msea.2006.04.153 ↗
14. A. Orozco-Caballero, S.K. Menon, C.M. Cepeda-Jiménez, P. Hidalgo-Manrique, T.R. McNelley, O.A. Ruano, F. Carreño: Materials Science and Engineering: A, 2014, 612, 162–71.10.1016/j.msea.2014.06.017 ↗
15. A.M. Abd El-Khalek: Materials Science and Engineering: A, 2009, 500, 176–81.10.1016/j.msea.2008.09.043 ↗
16. E. Gariboldi, K. Naumenko, O. Ozhoga-Maslovskaja, E. Zappa: Materials Science and Engineering: A, 2016, 652, 175–85.10.1016/j.msea.2015.11.090 ↗
17. F. Mohamed, T. Langdon: Metall. Trans., 1974, 5, 2339–45.10.1007/BF02644014 ↗
18. P. K. Chaudhury, F. Mohamed: Metall. Trans. A, 1987, 18, 2105–14.10.1007/BF02647082 ↗
19. F. Mohamed: Metall. Trans. A, 1978, 9, 1013–15.10.1007/BF02649848 ↗
20. K.L. Murty, F.A. Mohamed, J.E. Dorn: Acta Metall., 1972, 20, 1009–18.10.1016/0001-6160(72)90135-6 ↗
21. P. Yavari, F.A. Mohamed, T.G. Langdon: Acta Metall., 1981, 29, 1495–1507.10.1016/0001-6160(81)90184-X ↗
22. O. D. Sherby, P.M. Burke: Prog. Mater. Sci., 1968, 13, 323–90.10.1016/0079-6425(68)90024-8 ↗
23. O. D. Sherby, R. Klundt, A. Miller: Metall. Trans. A, 1977, 8, 843–50.10.1007/BF02661565 ↗
24. E. Rincon: Mechanical Properties as a Function of Temperature in an Aluminum Alloy A319, Instituto Tecnologico de Saltillo, Saltillo Coah, Mexico, June 2007.
25. J. Čadek, M. Pahutová, V. Šustek: Mater.Sci. Eng. A, 1998, 246, 252–64.10.1016/S0921-5093(97)00694-1 ↗
26. R.W. Lund, W.D. Nix: Metall. Trans. A, 1975, 6, 1329–33.10.1007/BF02641925 ↗
27. F.A. Mohamed, K.-T. Park, E.J. Lavernia: Mater.Sci. Eng. A, 1992, 150, 21–35.10.1016/0921-5093(90)90004-M ↗
28. S. Spigarelli, M. Cabibbo, E. Evangelista, S. Cucchieri: Mater. Lett., 2002, 56, 1059–63.10.1016/S0167-577X(02)00677-8 ↗
29. K. Park, E.J. Lavernia, F.A. Mohamed: Acta Metall. Mater., 1994, 42, 667–78.10.1016/0956-7151(94)90264-X ↗
30. ASTM E139-11, Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials, ASTM International, West Conshohocken, 2006.
31. M. Heimendahl: Introduction to Electron Microscopy, 1st ed., Verlag Vieweg Struttgart, 1970.
32. C. Puncreobutr, P.D. Lee, K.M. Kareh, T. Connolley, J.L. Fife, A.B. Phillion: Acta Materialia, 2014, 68, 42–51.10.1016/j.actamat.2014.01.007 ↗
33. E. Rincon, H.F. Lopez, M.M. Cisneros, H. Mancha: Mater.Sci. Eng. A, 2009, 519, 128–40.10.1016/j.msea.2009.05.022 ↗
34. L. Kloc, S. Spigarelli, E. Cerri, E. Evangelista, T. Langdon: Metall. Mater. Trans. A, 1996, 27, 3871–9.10.1007/BF02595636 ↗
35. J.C. Fisher: Acta Metall., 1954, 2, 9–10.10.1016/0001-6160(54)90087-5 ↗
36. Y. Li, T. Langdon: Metall. Mater. Trans. A, 1999, 30, 315–24.10.1007/s11661-999-0320-5 ↗
37. S.L. Robinson, O.D. Sherby: Acta Metall., 1969, 17, 109–25.10.1016/0001-6160(69)90132-1 ↗
38. A.B. Pandey, R.S. Mishra, Y.R. Mahajan: Acta Metall. Mater., 1992, 40, 2045–52.10.1016/0956-7151(92)90190-P ↗
39. H. Arami, R. Khalifehzadeh, H. Keyvan, F. Khomamizadeh: Journal of Alloys and Compounds, 2009, 468, 130–5.10.1016/j.jallcom.2008.01.020 ↗
40. E. Arzt, G. Dehm, P. Gumbsch, O. Kraft, D. Weiss: Prog. Mater. Sci., 2001, 46, 283–307.10.1016/S0079-6425(00)00015-3 ↗
41. J. Čadek, H. Oikawa, V. Šustek: Mater.Sci. Eng. A, 1995, 190, 9–23.10.1016/0921-5093(94)09605-V ↗
42. R.W. Lund, W.D. Nix: Acta Metall., 1976, 24, 469–481.10.1016/0001-6160(76)90068-7 ↗
43. B. Brown, R.K. Ham: Strengthening Methods in Crystals, Elsevier, Amsterdam, 1971.
44. E. Arzt, D.S. Wilkinson: Acta Metall., 1986, 34, 1893–98.10.1016/0001-6160(86)90247-6 ↗
45. N. Haghdadi, B. Bazaz, H.R. Erfanian-Naziftoosi, A.R. Kiani-Rashid: Int J Miner Metall Mater, 2012, 19, 812–20.10.1007/s12613-012-0633-z ↗
46. J. Rösler, E. Arzt: Acta Metall., 1988, 36, 1043–51.10.1016/0001-6160(88)90158-7 ↗
47. J. Rösler, E. Arzt: Acta Metall. Mater., 1990, 38, 671–83.10.1016/0956-7151(90)90223-4 ↗
48. J.H. Schröder, E. Arzt: Scripta Metall., 1985, 19, 1129–34.10.1016/0036-9748(85)90022-5 ↗
49. D.J. Srolovitz, R.A. Petkovic-Luton, M.J. Luton: Acta Metall., 1983, 31, 2151–59.10.1016/0001-6160(83)90034-2 ↗
50. P.K. Chaudhury, F.A. Mohamed: Mater.Sci. Eng. A, 1988, 101, 13–23.
51. D.C. Dunand, A.M. Jansen: Acta Mater., 1997, 45, 4569–81.10.1016/S1359-6454(97)00135-3 ↗
52. L. Kloc, S. Spigarelli, E. Cerri, E. Evangelista, T.G. Langdon: Acta Mater., 1997, 45, 529–40.10.1016/S1359-6454(96)00190-5 ↗
53. Y. Li, T.G. Langdon: Acta Mater., 1999, 47, 3395–403.10.1016/S1359-6454(99)00219-0 ↗
54. Y. Li, S.R. Nutt, F.A. Mohamed: Acta Mater., 1997, 45, 2607–20.10.1016/S1359-6454(96)00367-9 ↗
55. R.W. Evans, B. Wilshire: Creep of Metals and Alloys, Institute of Metals, London, 1985.
56. G. González-Doncel, O.D. Sherby: Acta Metall. Mater., 1993, 41, 2797–2805.10.1016/0956-7151(93)90094-9 ↗