Effect of Strain Rate on Hot Ductility Behavior of a High Nitrogen Cr-Mn Austenitic Steel
Source abstract
Abstract
18Mn18Cr0.6N steel specimens were tensile tested between 1173 K and 1473 K (900 °C and 1200 °C) at 9 strain rates ranging from 0.001 to 10 s−1. The tensile strained microstructures were analyzed through electron backscatter diffraction analysis. The strain rate was found to affect hot ductility by influencing the strain distribution, the extent of dynamic recrystallization and the resulting grain size, and dynamic recovery. The crack nucleation sites were primarily located at grain boundaries and were not influenced by the strain rate. At 1473 K (1200 °C), a higher strain rate was beneficial for grain refinement and preventing hot cracking; however, dynamic recovery appreciably occurred at 0.001 s−1 and induced transgranular crack propagation. At 1373 K (1100 °C), a high extent of dynamic recrystallization and fine new grains at medium strain rates led to good hot ductility. The strain gradient from the interior of the grain to the grain boundary increased with decreasing strain rate at 1173 K and 1273 K (900 °C and 1000 °C), which promoted hot cracking. Grain boundary sliding accompanied grain rotation and did not contribute to hot cracking.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. J.W. Simmons: Mater. Sci. Eng. A, 1996, vol. 207, pp. 159–69.10.1016/0921-5093(95)09991-3 ↗
2. J.W. Simmons: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 156–60.
3. R.D. Knutsen, C.I. Lang, J.A. Basson: Acta Mater., 2004, vol. 52, pp. 2407–17.10.1016/j.actamat.2004.01.031 ↗
4. Z.H. Wang, W.T. Fu, S.H. Sun, H. Li, Z.Q. Lv, D.L. Zhao: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1025–32.10.1007/s11661-009-0153-2 ↗
5. Z.H. Wang, S.H. Sun, B. Wang, Z.P. Shi, W.T. Fu: Mater. Sci. Eng. A, 2015, vol. 625, pp. 321–30.10.1016/j.msea.2014.12.022 ↗
6. Z.H. Wang, W.T. Fu, S.H. Sun, Z.Q. Lv, W.H. Zhang: J. Mater. Sci. Technol., 2010, vol. 26, pp. 798–802.10.1016/S1005-0302(10)60127-2 ↗
7. Z.H. Wang, S.H. Sun, B. Wang, Z.P. Shi, R.H. Zhang, W.T Fu: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 3631–9.10.1007/s11661-014-2290-5 ↗
8. R.D. Doherty, D.A. Hughes, F.J. Humphreys, J.J. Jonas, D. Juul, M.E. Kassner, W.E. King, T.R. McNelley, H.J. McQueen, A.D. Rollett: Mater. Sci. Eng. A, 1997, vol. 238, pp. 219–74.10.1016/S0921-5093(97)00424-3 ↗
9. J. Moon, T.H. Lee, J.H. Shin, J.W. Lee: Mater. Sci. Eng. A, 2014, vol. 594, pp. 302–08.10.1016/j.msea.2013.11.090 ↗
10. E. Erisir, U. Prahl, W. Bleck: Mater. Sci. Eng. A, 2010, vol. 528, pp. 519–25.10.1016/j.msea.2010.09.045 ↗
11. J. Deng, Y.C. Lin, S.S. Li, J. Chen, Y. Ding: Mater. Design, 2013, vol. 49, pp. 209–09.10.1016/j.matdes.2013.01.023 ↗
12. S.W. Kim, Y.S. Lee: Metall. Mater. Trans. B, 2014, vol. 45B, pp. 445–53.10.1007/s11663-013-9886-9 ↗
13. J. Liu, L.H. Qi, P. Liu, J.T. Guan, J.M. Zhou: Mater. Sci. Eng. A, 2014, vol. 596, pp. 157–64.10.1016/j.msea.2013.12.056 ↗
14. O. Sabokpa, A. Zarei-Hanzaki, H.R. Abedi: Mater. Sci. Eng. A, 2012, vol. 550, pp. 31–38.10.1016/j.msea.2012.03.112 ↗
15. S.P. Tan, Z.H. Wang, S.C. Cheng, Z.D. Liu, J.C. Han, W.T. Fu: Mater. Sci. Eng. A, 2009, vol. 517: 312–15.10.1016/j.msea.2009.04.028 ↗
16. J.L. He, Z.S. Cui, F. Chen, Y.H. Xiao, L.Q. Ruan: Mater. Design, 2013, vol. 52, pp. 547–55.10.1016/j.matdes.2013.05.080 ↗
17. M. Faccoli, R. Roberti: J. Mater. Sci., 2013, vol. 48, pp. 5196–23.10.1007/s10853-013-7307-8 ↗
18. E. Hurtado-Delgado, R.D. Morales: Metall. Mater. Trans. B, 2001, vol. 32B, pp. 919–27.10.1007/s11663-001-0078-7 ↗
19. G.Q. Hou, L. Zhu, H.X. Bian, Y.L. Tian: Chinese J. Mater. Research, 2013, vol. 27, pp. 70–74 (in Chinese).
20. X.W. Duan, J.S. Liu: Mater. Sci. Eng. A, 2013, vol. 588: 265–71.10.1016/j.msea.2013.08.078 ↗
21. X.P. Wei, W.W. He, J.S. Liu: J. Taiyuan Univ. Sci. Tech., 2012, vol. 31, pp. 296–99 (in Chinese).
22. H.J. McQueen: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 345–62.10.1007/s11661-002-0096-3 ↗
23. I. Bantounas, T.C. Lindley, D. Rugg, D. Dye: Acta Mater., 2007, vol. 55, pp. 5655–65.10.1016/j.actamat.2007.06.034 ↗
24. N. Subrahmanya, N. Naveen, R. Narasimhan, S. Suwas: Acta Mater., 2015, vol. 94: 281–93.10.1016/j.actamat.2015.04.054 ↗
25. A. Clair, M. Foucault, O. Calonne, E. Finot: Scripta Mater., 2014, vol. 82, pp. 21–24.10.1016/j.scriptamat.2014.03.010 ↗
26. W.H. Zhang, S.H. Sun, D.L. Zhao, B.Z. Wang, Z.H. Wang, W.T. Fu: Mater. Design, 2011, vol. 32, pp. 4173–79.10.1016/j.matdes.2011.04.043 ↗
27. D. Ponge, G. Gottstein: Acta Mater., 1998, vol. 46, pp. 69–80.10.1016/S1359-6454(97)00233-4 ↗
28. S. Kibey, J.B. Liu, M.J. Curtis, D.D. Johnson, H. Sehitoglu: Acta Mater., 2006, vol. 54, pp. 2991–3001.10.1016/j.actamat.2006.02.048 ↗
29. F.J. Humphreys, M. Hatherly: Recrystallization and related annealing phenomena, 2nd ed., Elsevier, Oxford, 2004, p. 131.
30. B. Mintz: ISIJ Int., 1999, vol. 39, pp. 833–55.10.2355/isijinternational.39.833 ↗
31. F. Zarandi, S. Yue: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 3823–32.10.1007/s11661-004-0288-0 ↗
32. M.H. Kang, J.S. Lee, Y.M. Koo, S.J. Kim, N.H. Heo: Metall. Mater. Trans. A, 2014, vol. 45A: 4302–06.10.1007/s11661-014-2402-2 ↗