In-Situ Fracture Studies and Modeling of the Toughening Mechanism Present in Wrought Low-Carbon Arc-Cast Molybdenum, Titanium-Zirconium-Molybdenum, and Oxide-Dispersion-Strengthened Molybdenum Flat Products
Source abstract
Abstract
In-situ testing, ultrasonic C-scans, and metallography were used to show that a crack-divider delamination form of thin-sheet toughening occurs in wrought low-carbon arc-cast (LCAC) unalloyed molybdenum, oxide-dispersion-strengthened (ODS) molybdenum, and a wrought molybdenum alloy with 0.5 pct Ti and 0.1 pct Zr additions by weight (TZM), at temperatures greater than or equal to the ductile-to-brittle transition temperature (DBTT). Cracking along boundaries relieves mechanical constraints and frees ligaments that may plastically stretch to produce toughening. Anisotropy in fracture toughness with lower values in the short-transverse (ST) direction is shown to produce the crack-divider delaminations at the crack tip in the longitudinal (LT) and transverse (TL) orientations. The delamination zone increases with increasing stress-intensity factors to sizes significantly larger than the plastic zone; this leads to large increases in fracture toughness by the thin-sheet-toughening mechanism. Fracture in ODS Mo alloys proceeds mainly along grain boundaries to produce small ligaments that exhibit ductility for both LT and TL orientations, resulting in a lower DBTT and higher toughness values at lower temperatures than those observed in LCAC molybdenum and TZM. A combination of grain-boundary fracture and cleavage is prevalent in LCAC molybdenum and TZM. The predominant tendency for microcracking along grain boundaries to leave fine, ductile ligaments in ODS molybdenum can be attributed to a fine-grained microstructure with a ≈1- to 2-μm thickness of sheetlike grains. The presence of mixed grain-boundary fracture and cleavage in LCAC molybdenum and TZM can be attributed to a microstructure with a larger thickness of sheetlike grains (4 to 15 μm).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. J.B. Lambert, J.J. Rausch: Non-Ferrous Alloys and Special-Purpose Materials, Materials Handbook, Vol. 2, ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 557–82
2. R.E. Gold, D.L. Harrod: J. Nucl. Mater., 1979, vol. 85, pp. 805–1510.1016/0022-3115(79)90359-3 ↗
3. B.L. Cox, F.W. Wiffen: J. Nucl. Mater., 1979, vol. 85, pp. 901–0510.1016/0022-3115(79)90375-1 ↗
4. G.R. Smolik, D.A. Petti, and S.T. Schuetz: J. Nucl. Mater., 2000, vols. 283–287, pp. 1458–6210.1016/S0022-3115(00)00303-2 ↗
5. J. Wadsworth, T.G. Nieh, J.J. Stephens: Int. Mater. Rev., 1988, vol. 33 (3), pp. 131–5010.1179/imr.1988.33.1.131 ↗
6. R.N. Orava: in Refractory Metals and Alloys IV–Research and Development, K.I. Jaffee, G.M. Ault, J. Maltz, M. Semchyshen, eds., Gordon and Breach, New York, NY, 1967, pp. 117–40
7. B.A. Wilcox, A. Gibert: in Refractory Metals and Alloys IV–Research and Development, K.I. Jaffee, G.M. Ault, J. Maltz, M. Semchyshen, eds., Gordon and Breach, New York, NY, 1967, pp. 95–115
8. A. Lawley: in Refractory Metals and Alloys IV– Research and Development, K.I. Jaffee, G.M. Ault, J. Maltz, M. Semchyshen, eds., Gordon and Breach, New York, NY, 1967, pp. 141-60
9. B.S. Lemet, K. Kreder: in Refractory Metals and Alloys IV–Research and Development, K.I. Jaffee, G.M. Ault, J. Maltz, M. Semchyshen, eds., Gordon and Breach, New York, NY, 1967, pp. 161–83
10. H. Kurishta, A. Oishi, H. Kubo, H. Yoshinaga: Trans. J. Inst. Met., 1985, vol. 26 (5), pp. 341–5210.2320/matertrans1960.26.341 ↗
11. H. Kurishita, H. Yoshinaga: Mater. Forum, 1989, vol. 13, pp. 161–73
12. S. Tsurelawa, T. Tanaka, H. Yoshinaga: Mater. Sci. Eng., 1994, vol. A176, pp. 341–4810.1016/0921-5093(94)90997-0 ↗
13. A. Kumar, B.L. Eyre: Proc. R. Soc. London, 1980, vol. A370, pp. 431–58
14. B.V. Cockeram: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3685–370710.1007/s11661-002-0242-y ↗
15. B.V. Cockeram: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1777–9110.1007/s11661-005-0042-2 ↗
16. B.V. Cockeram: Mater. Sci. Eng A, 2006, vol. 418, pp. 120–3610.1016/j.msea.2005.11.030 ↗
17. C. Grandhi, M.F. Ashby: Acta Metall., 1979, vol. 27, pp. 1565–160210.1016/0001-6160(79)90042-7 ↗
18. M. Semchyshen, R.Q. Barr: J. Less-Common Met., 1966, vol. 11, pp. 1–1310.1016/0022-5088(66)90052-X ↗
19. J.C. Thornley, A.S. Wronski: Acta Metall., 1970, vol. 18, pp. 1053–6210.1016/0001-6160(70)90002-7 ↗
20. A.A. Johnson, S.P. Gupta, S.P. Kodali: Mater. Sci. Eng, 1975, vol. 18, pp. 159–6110.1016/0025-5416(75)90083-X ↗
21. S. Morozumi: Proc. Mechanical Properties of Bcc Metals, TMS-AIME, Warrendale, PA, 1982, pp. 197–205
22. A. Lawley, J. Van den Sype, and R. Maddin: J. Inst. Met., 1962–1963, vol. 91, pp. 23–27
23. G.W. Brock: Trans. TMS-AIME, 1961, vol. 221, pp. 1055–62
24. W.D. Klopp: J. Less Common Met., 1975, vol. 42, pp. 261–7810.1016/0022-5088(75)90046-6 ↗
25. J. Wadsworth, T.G. Nieh, J.J. Stephens: Scripta Metall., 1986, vol. 20, pp. 637–4210.1016/0036-9748(86)90481-3 ↗
26. K.S. Chan: Metall. Trans. A, 1989, vol. 20A, pp. 155–6410.1007/BF02647502 ↗
27. K.S. Chan: Metall. Trans. A, 1989, vol. 20A, pp. 2337–4410.1007/BF02666668 ↗
28. K.T. Venkateswara Rao, W. Yu, R.O. Ritchie: Metall. Trans. A., 1988, vol. 19A, pp. 549–6110.1007/BF02649269 ↗
29. J.D. Embury, N.J. Petch, A.E. Wraith, and E.S. Wright: Trans. AIME, 1967, vol. 239, pp. 114-18
30. S. Yokoshima, M. Yamaguchi: Acta Metall., 1996, vol. 44 (3), pp. 873–83
31. R.R. Adharapurapu, K.S. Vecchio, A. Rohatgi, F. Jiang: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 3217–3610.1007/s11661-005-0092-5 ↗
32. Standard Specification for Molybdenum and Molybdenum Alloy Plate, Sheet, Strip, and Foil, ASTM B386-91, ASTM, Philadelphia, PA, 1997
33. R. Bianco, R.W. Buckman, Jr., and C.B. Geller: High Strength, Creep-Resistant Molybdenum Alloy and Process For Producing the Same, U.S. Patent No. 5,868,876, Feb. 9, 1999.
34. A.J. Mueller, J.A. Shields, and R.W. Buckman Jr.: Proc. 15th Int. Plansee Sem., Vol. 1, G. Kneringer, P. Rodhammer, H. Wildner, eds., Plansee Holding AG, Reutte, Austria, 2001, pp. 485–97
35. K S. Chan: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2518–3110.1007/BF02652346 ↗
36. Standard Terminology Relating to Fatigue and Fracture Testing, ASTM E1823-96, ASTM, Philadelphia, PA, 1996
37. ASTM E812-97, ASTM, Philadelphia, PA, 1997
38. ASTM E813-95, ASTM, Philadelphia, PA, 1995
39. T.G.F. Gray: Int. J. Fract., 1977, vol. 13 (1), pp. 65–7510.1007/BF00040876 ↗
40. A. Nagy, J.B. Campbell, D.L. Davidson: Rev. Sci. Instrum., 1984, vol. 55, pp. 778-8210.1063/1.1137816 ↗
41. Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials, ASTM E399-90, ASTM, Philadelphia, PA, 1997
42. D.R. Williams, D.L. Davidson, J. Lankford: Exp. Mech., 1980, vol. 20, pp. 134-3910.1007/BF02321294 ↗
43. E.A. Franke, D.J. Wenzel, D.L. Davidson: Rev. Sci. Instrum., 1990, vol. 62 (5), pp. 1270–7910.1063/1.1142484 ↗
44. Standard Test Method for Measurement of Fracture Toughness, ASTM E1820-01, ASTM, Philadelphia, PA, 2001
45. X.Q. Feng, D. Gross: Int. J. Damage Mech., 2000, vol. 9, pp. 79–11210.1106/Q5T5-BXFP-62JR-4MWV ↗
46. M.-Y. He, J.W. Hutchinson: Int. J. Solids Struct., 1989, vol. 25 (9), pp. 1053–6710.1016/0020-7683(89)90021-8 ↗
47. Z. Jiuxing, L. Lu, Z. Meiling, H. Yancao, Z. Tieyong: Int. J. Refract. Met. Hard Mater., 1999, vol. 17, pp. 405–0910.1016/S0263-4368(99)00030-X ↗