Quantitative Measurements of Grain Boundary Sliding in an Ultrafine-Grained Al Alloy by Atomic Force Microscopy
Source abstract
Abstract
In the current study, quantitative measurements for grain boundary sliding (GBS) in ultrafine-grained (UFG) 5083 Al by atomic force microscopy (AFM) were performed. An ion beam polishing and etching technique was used to reveal grain boundaries in the alloy for AFM characterization. A comparison between the average grain sizes measured from AFM images and those estimated from transmission electron microscopy micrographs and electron backscatter diffraction (EBSD) maps showed excellent agreement. The vertical offset of GBS was measured by comparing predeformation and postdeformation AFM images. By analyzing these measurements, the contribution of GBS to the total tensile strain in 5083 Al was estimated as 25 pct at a strain rate of 10−4 seconds−1 and a temperature of 473 K (200 °C). It was demonstrated that the relatively low value of the contribution of GBS to the total strain is most likely the result of testing UFG 5083 Al under experimental conditions that favor the dominance of region I (low-stress region) of the sigmoidal behavior characterizing high-strain-rate superplasticity, which was reported previously for the alloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. T.G. Langdon and R.Z. Valiev: Prog. Mater. Sci., 2006, vol. 51. p. 881.10.1016/j.pmatsci.2006.02.003 ↗
2. M. Chauhan, I. Roy, E.J. Lavernia, and F.A. Mohamed: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2715-25.10.1007/BF02586105 ↗
3. I. Roy, M. Chauhan, E. J. Lavernia, and F.A. Mohamed: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 721-30.10.1007/s11661-006-0044-8 ↗
4. B.P. Kasyap and A.K. Mukherjee: Res. Mech., 1986, vol. 17. pp. 293-355.
5. N. Ridley, D.W. Livesey, and A.K. Mukherjee: J. Mater. Sci., 1984, vol. 19, pp. 1321-32.10.1007/BF01120044 ↗
6. X.G. Jiang, J.C. Earthman, and F.A. Mohamed: J. Mater. Sci., 1994, vol. 29, pp. 5499-514.10.1007/BF00349941 ↗
7. A. Ayensu and T.G. Langdon: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 901-07.10.1007/BF02649757 ↗
8. R.B. Vastava and T.G. Langdon: Acta Metall., 1979, vol. 27, pp. 251-57.10.1016/0001-6160(79)90103-2 ↗
9. T.G. Langdon: Metall. Trans. A, 1982, vol. 13, pp. 689-701.10.1007/BF02642383 ↗
10. Z.R. Lin, A.H. Chokshi, and T.G. Langdon: J. Mater. Sci., 1988, vol. 23, pp. 2712-22.10.1007/BF00547441 ↗
11. K. Duong and F.A. Mohamed: Acta Metall., 1998, vol. 46, pp. 4571-86.
12. K. Duong and F.A. Mohamed: Metall. Mater. Trans. A, 2000, vol. 32A, pp. 103-13.
13. T.G. Langdon: J. Mater. Sci., 2006, vol. 41, pp. 597-609.10.1007/s10853-006-6476-0 ↗
14. W.W. Gerberich, S.E. Harvey, D.E. Kramer, and J. W. Hoehn: Acta Mater., 1998, vol. 46, pp. 5007-21.10.1016/S1359-6454(98)00169-4 ↗
15. L. Cretegny and A. Saxena: Acta Mater, 2001, vol. 49, pp. 3755-65.10.1016/S1359-6454(01)00271-3 ↗
16. Y. Choi, W.Y. Choo, and D. Kwon: Scripta Mater., 2001, vol. 45, pp. 1401-06.10.1016/S1359-6462(01)01176-9 ↗
17. Y. Huang and T.G. Langdon: J. Mater. Sci., 2002, vol. 37, pp. 4993-98.10.1023/A:1021071228521 ↗
18. V.L. Tellkamp, S. Dallek, D. Cheng, and E.J. Lavernia: J. Mater. Res., 2001, vol. 16, pp. 938-44.10.1557/JMR.2001.0133 ↗
19. L. Clarisse, A. Bataille, Y. Pennec, J. Crampon, and R. Duclos: Ceramics Int., 1999, vol. 25, pp. 389-94.10.1016/S0272-8842(98)00044-3 ↗
20. V. Randle: Advances in Images and Electron Physics, vol. 151, Elsevier, Amsterdam, The Netherlands, 2008, pp. 263-411.
21. I. Roy, H. Yang, L. Dinh, I. Lund, J. Earthman, and F.A. Mohamed: Scripta Mater., 2008, vol 59, no. 3, p. 305.10.1016/j.scriptamat.2008.03.033 ↗
22. A. Torrents, H. Yang, and F.A. Mohamed: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 621-30.10.1007/s11661-009-0147-0 ↗
23. I. Roy, S. Dheda, and F.A. Mohamed: University of California, Irvine, 2011, unpublished research.
24. R.L. Bell, C. Graeme-Barber, and T.G. Langdon: AIME Met. Soc. Trans., 1967, vol. 239, pp. 1821-24.
25. R.C. Gifkins: Superplastic Forming of Structural Alloys, N.E. Paton and C.H. Hamilton, eds., Metallurgical Society of AIME, San Diego, CA, 1982, pp. 2–26.
26. F.A. Mohamed and T.G. Langdon: Acta. Metall., 1975, vol. 23, pp. 117-24.10.1016/0001-6160(75)90076-0 ↗
27. F.A. Mohamed, S.A. Shei, and T.G. Langdon: Acta. Metall., 1975, vol. 23, pp. 1443-50.10.1016/0001-6160(75)90153-4 ↗
28. F.A. Mohamed and T.G. Langdon: Phil. Mag., 1975, vol. 32, pp. 697-709.10.1080/14786437508221614 ↗
29. S.H. Vale, D.J. Eastgate, and P.M. Hazzledine: Scripta Metall., 1979, vol. 13, pp. 1157-62.10.1016/0036-9748(79)90274-6 ↗
30. D.W. Livesey and N. Ridley: Scripta Metall., 1982, vol. 16, pp. 165-68.10.1016/0036-9748(82)90378-7 ↗
31. S.A. Shei and T.G. Langdon: Acta. Metall., 1978, vol. 26, pp. 638-46.
32. A.H. Chokshi and T.G. Langdon: Metall. Trans. A, 1988, vol. 19A, pp. 2487-96.10.1007/BF02645476 ↗
33. S. Yan, J.C. Earthman, and F.A. Mohamed: Phil. Mag., 1994, vol. 69, pp. 1017-38.10.1080/01418619408242236 ↗
34. A.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Progr. Mater. Sci., 2000, vol. 45, pp. 103-89.10.1016/S0079-6425(99)00007-9 ↗
35. C. Suranarayana: Mechanical Alloying and Milling, Marcel Dekker, Inc., New York, NY, 2004, pp. 333-58.10.1201/9780203020647.ch13 ↗
36. D.B. Witkin and E.J. Lavernia: Progr. Mater. Sci., 2006, vol. 51, no. 1, pp. 1-60.10.1016/j.pmatsci.2005.04.004 ↗
37. F.A. Mohamed: Mater. Sci. Eng. A, 2011, vol. 528, pp. 1431-35.10.1016/j.msea.2010.10.048 ↗
38. F.A. Mohamed: J. Mater. Sci., 1983, vol. 18, pp. 582-92.10.1007/BF00560647 ↗
39. Y. Li, S.R. Nutt, and F.A. Mohamed: Acta Mater., 1997, vol. 45, pp. 2607-20.10.1016/S1359-6454(96)00367-9 ↗
40. K.T. Park, E.J. Lavernia, and F.A. Mohamed: Acta Metall. Mater., 1990, vol. 38, pp. 2149-59.10.1016/0956-7151(90)90082-R ↗
41. H. Gleiter and B. Chalmers: Progr. Mater. Sci., 1972, vol. 16, pp. 1-12.10.1016/0079-6425(72)90017-5 ↗