journal article·2015-10

Impact Welding of Aluminum to Copper and Stainless Steel by Vaporizing Foil Actuator: Effect of Heat Treatment Cycles on Mechanical Properties and Microstructure

Anupam Vivek, Steven Hansen, Jake Benzing, Mei He, Glenn Daehn

Publisher page

Abstract

This work studies the mechanical property effect of microstructure on impact welds of aluminum alloy AA6061 with both copper alloy Cu 110 and stainless steel AISI 304. AA6061-T6 and T4 temper aluminum sheets of 1 mm thickness were launched toward copper and stainless steel targets using the vaporizing foil actuator technique. Flyer plate velocities, measured via photonic Doppler velocimetry, were observed to be approximately 800 m/s. The welded aluminum-copper samples were subjected to instrumented peel testing, microhardness testing, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. The welded joints exhibited cracks through their continuous intermetallic layers. The cracks were impeded upon encountering a ductile metallic wave. The welds created with T6 temper flyer sheets were found to have smaller intermetallic-free and wavy interface regions as compared to those created with T4 temper flyer sheets. Peel strength tests of the two weld combinations resulted in failure along the interface in the case of the T6 flyer welds, while the failure generally occurred in the parent aluminum for the T4 temper flyer welds. Half of the T4 flyer welds were subjected to aging for 18 h at 433 K (160 °C) to convert the aluminum sheet to the T6 condition. Although the aged flyer material did not attain the hardness of the as-received T6 material, it was found to be significantly stronger than the T4 material. These welds retained their strength after the aging process, and diffusion across the interface was minimal. The welded aluminum-stainless steel samples were analyzed on a more basic level than aluminum-copper samples, but were found to exhibit similar results.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. W.G. Chace and H.K. Moore, eds: Exploding Wires, Plenum Press, New York, 1959, vol. 4.10.1007/978-1-4615-8975-4 ↗
2. Keller DV, Penning RJ (1962) Exploding Wires. W. Chase, H. Moore (eds). Plenum Press, New York, vol 2, pp. 263-77.10.1007/978-1-4684-7505-0_21 ↗
3. J.R. Stroud: A New Kind of Detonator—The Slapper, 1976, UCRL-77639.
4. Chau HH, Dittbener G, Hofer WW, Honodel CA, Steinberg DJ, Stroud JR, Weingart RC, Lee RS (1980) Rev. Sci. Instrum. 51:1676-81.10.1063/1.1136155 ↗
5. A. Vivek, G.S. Daehn, G.A. Taber, and J.R. Johnson: U.S. Patent Application 13/838,556, 2013.
6. Crossland, B., 1982, Explosive Welding of Metals and Its Application, Oxford University Press, New York.
7. Psyk, V., Risch, D.,Kinsey, B. L.,Tekkaya, A. E.,Kleiner,M., 2011, J. Mater. Process. Technol., 211, 787-829.10.1016/j.jmatprotec.2010.12.012 ↗
8. Cooper, P., 1997, Explosives Engineering, Wiley-VCH, pp. 290-93.
9. Vivek, A., Hansen, S.R., Liu, B.C., and Daehn, G.S., 2013, J. Mater. Process. Technol., 213, pp. 2304-11.10.1016/j.jmatprotec.2013.07.006 ↗
10. A.A. Deribas, V.A. Simonov, and I.D. Zakcharenko: Investigations on Explosive Welding Parameters for Arbitrary Combinations of Metals and Alloys, Proceedings of the 6th International Conference of High Energy Rate Fabrication, 1975, vol. 4, p. 1024.
11. Johnson, J. R., Taber, G., Vivek, A., Zhang, Y., Golowin, S., Banik, K., and Daehn, G. S., 2009, Steel Res. Int., 80, 359-65.
12. Vivek, A., Liu, B. C.,Hansen, S. R.,and Daehn,G. S., 2014, J. Mater. Process. Technol. 214(8) 1583-89.10.1016/j.jmatprotec.2014.03.007 ↗
13. G.R. Cowan, O.R. Bergmann, and A.H. Holtzman: Metall. Trans., 1971, vol. 2, pp. 3145–55.10.1007/BF02814967 ↗
14. F.H. Webb, N. Chase, M. Ernstene, and A.V. Tollestrup: Exploding Wires, 1959, vol. 1, p. 33.10.1007/978-1-4615-8975-4_3 ↗
15. Song, J., Kostka, A. Veehmayer, M., and Raabe, D., 2011, Mater. Sci. Eng. A, 528, pp. 2641-47.10.1016/j.msea.2010.11.092 ↗
16. Grignon, F., Benson, D., Vecchio, K.S., Meyers, M.A., 2004, Int. J. Impact Eng., 30, pp. 1333-51.10.1016/j.ijimpeng.2003.09.049 ↗
17. Akbari Mousavi, S. A. A., and Farhadi Sartangi, P., 2009 Mater. Des. 30(3), 459-68.10.1016/j.matdes.2008.06.016 ↗
18. Zhang, Y., Babu, S. S., and Daehn, G. S., 2010, J. Mater. Sci., 45, pp. 4645-51.10.1007/s10853-010-4676-0 ↗
19. Rosenthal, I., Miriyev, A.,Tuval, E., Stern,A., Frage,N., 2014, Metallogr. Microstruct. Anal. 3, pp. 97-103.10.1007/s13632-014-0120-1 ↗