journal article·2013-12

Effect of Heat Treatment on Morphology of Fe-Rich Intermetallics in Hypereutectic Al-Si-Cu-Ni Alloy with 1.26 pct Fe

Meng Sha, Shusen Wu, Li Wan, Shulin Lü

Publisher page

Abstract

Cobalt is generally considered as the element that can neutralize the negative effects of iron in Al alloys, such as inducing fracture and failure for stress concentration. Nevertheless, Fe-rich intermetallics would be inclined to form coarse plate-like δ-Al4(Fe, Co, Ni)Si2 particles when the content of Fe was high, which could also cause inferior mechanical properties. The dissolution and transformation of δ-Al4(Fe, Co, Ni)Si2 phase in solution heat-treated samples of Al-20Si-1.85Cu-1.05Ni-1.26Fe-1.35Co alloy were studied using optical microscopy, image analysis, and scanning electron microscopy. The effects of solution heat treatment time ranging from 0 to 9 hours at 783.15 K (510 °C) on mechanical properties were also investigated. The coarse plate-like δ-Al4(Fe, Co, Ni)Si2 particles varied slowly through concurrent dissolution along widths and at the plate tips as solution treatment time increased, which could be explained from diffusion-induced grain boundary migration. Solution heat treatment also has an important influence on mechanical properties. The maximum ultimate tensile strength and yield strength after T6 treatment were 258 and 132 MPa, respectively, while the maximum hardness was 131 HB. Compared with those of the samples in the as-cast state, they increased by 53, 42, and 28 pct, respectively. Moreover, δ-Al4(Fe, Co, Ni)Si2 phase, which appears as a coarse plate-like particle in two dimensions, is actually a cuboid in three dimensions. The length of this cuboid is close to the width, while the height is much smaller.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. S.S. Wu, X.L. Tu, Y. Fukuda, T. Kanno, and H. Nakae: Trans. Nonferrous Met. Soc. China, 2003, vol. 13, pp. 1285–89.
2. X. Cao and J. Campbell: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1425–35.10.1007/s11661-004-0251-0 ↗
3. P. Jonason: AFS Trans., 1992, vol. 100, pp. 601–07.
4. L.G. Hou, H. Cui, Y.H. Cai, and J.S. Zhang: Mater. Sci. Eng., A, 2009, vol. 527, pp. 85–92.10.1016/j.msea.2009.07.041 ↗
5. H.J. Huang, Y.H. Cai, H. Cui, J.F. Huang, J.P. He, and J.S. Zhang: Mater. Sci. Eng., A, 2009, vol. 502, pp. 118–25.10.1016/j.msea.2008.10.005 ↗
6. A. Couture: Int. Cast Met. Res., 1981, vol. 6, pp. 9–17.
7. M. Sha, S.S. Wu, X.T. Wang, and L. Wan: J. Alloys Compd., 2013, vol. 551, pp. 468–74.10.1016/j.jallcom.2012.10.181 ↗
8. A.M. Samuel, J. Gauthier, and F.H. Samuel: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1785–98.10.1007/BF02651928 ↗
9. G. Gustafsson, T. Thorvaldsson, and G.L. Dunlop: Metall. Trans. A, 1986, vol. 17, pp. 45–52.10.1007/BF02644441 ↗
10. L.A. Narayanan, F.H. Samuel, and J.E. Gruzleski: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2161–74.10.1007/BF02670687 ↗
11. Y. Shimizu, Y. Awano, and M. Nakamura: J. Jpn. Inst. Light Met., 1988, vol. 38, pp. 202–07.10.2464/jilm.38.202 ↗
12. Y. Shimizu, Y. Awano, and M. Nakamura: J. Jpn. Inst. Light Met., 1990, vol. 40, pp. 188–94.10.2464/jilm.40.188 ↗
13. M. Sha, S.S. Wu, X.T. Wang, L. Wan, and P. An: Mater. Sci. Eng., A, 2012, vol. 535, pp. 258–63.10.1016/j.msea.2011.12.077 ↗
14. N.A. Belov, D.G. Eskin, and N.N. Avxentieva: Acta Mater., 2005, vol. 53, pp. 4709–22.10.1016/j.actamat.2005.07.003 ↗
15. C. Lin, S.S. Wu, S.L. Lv, P. An, and L. Wan: Intermetallics, 2013, vol. 32, pp. 176–83.10.1016/j.intermet.2012.09.001 ↗
16. J.W. Cahn, J.D. Pan, and R.W. Balluffi: Scripta Metall., 1979, vol. 13, pp. 503–09.10.1016/0036-9748(79)90078-4 ↗
17. R.W. Balluffi and J.W. Cahn: Acta Metall., 1980, vol. 29, pp. 493–500.10.1016/0001-6160(81)90073-0 ↗
18. M. Hillert and G.R. Purdy: Acta Metall., 1978, vol. 26, pp. 333–40.10.1016/0001-6160(78)90132-3 ↗
19. R.W. Cahn and P. Haasen: Physical Metallurgy, 3rd ed., North-Holland Physics Publishing, Amsterdam, 1983, p. 452.
20. A.M. Samuel, F.H. Samuel, and H.W. Doty: J. Mater. Sci., 1996, vol. 31, pp. 5529–39.10.1007/BF01159327 ↗