Verification of the Simulated Residual Stress in the Cross Section of Gray Cast Iron Stress Lattice Shape Casting via Thermal Stress Analysis
Source abstract
Abstract
The residual stresses in the thick part of the stress lattice shape casting consist of the residual stress due to the temperature differential between the thick part and the thin part and the residual stress due to the temperature differential in the radial direction of the thick part. In this study, the gray cast iron stress lattice shape castings were cast and both types of the residual stresses were separately measured. Thermal stress analyses based on the casting experiment were conducted. Next, the measurements in this study were compared with both types of the simulated residual stresses. The thermal stress analyses estimated the residual stress due to the temperature difference in the radial direction of the thick part to be significantly higher than the measurement, although the residual stress due to the temperature difference between the thick part and the thin part was successfully predicted within a 10 pct error. Thus, this study suggested the introduction of the mechanical melting temperature, above which the very low yield stress is applied conveniently to describe the losses of the deformation resistance of the casting, to more accurately predict the residual stress due to the temperature difference in the radial direction of the thick part. From the verification of the suggested model, this study demonstrated that the conventional elasto-plastic model must introduce the mechanical melting temperature to predict the residual stress due to the temperature difference in the radial direction of the thick part and thus the overall residual stress in the stress lattice.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. Makino H., Ono T, Ohtsuka Y., Matsubara N.: Imono, vol.63(12), 1991, pp. 959–64.
2. B. Liu, R. Zhu, S. Xiong and Y. Zhang: Adv. Mater. Res., vol.4-5, 1997, pp. 551–56.10.4028/www.scientific.net/AMR.4-5.551 ↗
3. B.C. Liu, J.W. Kang and S.M. Xiong: Sci. Technol. Adv. Mater., 2, 2001, pp. 157–64.10.1016/S1468-6996(01)00041-9 ↗
4. A. Jacot, D. Maijer. and S. Cockroft: Metall. Mater. Trans. A, vol.31A, 2000, pp. 1201–11.
5. S.-M. Lee, W.-J. Lee: J. Mater. Eng. Perform., vol.14 (3), 2005, pp. 388–94.10.1361/10599490523931 ↗
6. C. Li and R.K. Huff: Modeling of Casting, Welding and Advanced Solidification Processes-XI, 2006, pp. 209–16.
7. C.P. Yeh, W.S. Hwang, C.H. Lin: Int. J. Cast Met. Res., vol. 22 no 1-4, 2009, pp.127–30.
8. Y. Motoyama, H. Takahashi, T. Okane, Y. Fukuda, and M. Yoshida: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 3261–70.10.1007/s11661-013-1683-1 ↗
9. A. Yoshizawa, L. Wang: Sokeizai, 49(5), 2008, pp. 1–5.
10. E. Gustafsson, M. Hofwing, N. Strömberg: J. Mater. Process. Technol., 209, 2009, pp. 4320–28.10.1016/j.jmatprotec.2008.11.025 ↗
11. Z. lgnaszak, P. Popielarski: Defect Diffus. Forum, vol. 312-315, 2011, pp.758–63.10.4028/www.scientific.net/DDF.312-315.758 ↗
12. E.M. Johnson, T.R. Watkins, J.E. Schmidlin, and S.A. Dutler: Metall. Mater. Trans. A, 2011, vol. 43A, pp. 1487–96.
13. J.-W. Kang, H.-M. Long, T.-J. Wang: Int. J. Cast Met. Res., vol.24 no. 3/4, 2011, pp. 228–32.10.1179/136404611X13001922708678 ↗
14. B.-H. Choi, J.-H Nam, S.-W Lee, S.-Y Kwak, J.-K. Choi: Int. J. Cast Met. Res., vol. 20 no. 2, 2007, pp.58–63.10.1179/136404607X216622 ↗
15. Sachs, G.: Zeitschrift fur Metalkunde, 19, 1927, pp. 352–57.
16. Y. Ueda, H. Murakawa, and N. Ma: Welding Deformation and Residual Stress Prevention, Butterworth-Heinemann, Oxford, 2012, p. 64.
17. T. Terasaki: J. Jpn. Weld. Soc., vol. 78, 2009, pp.55–56.10.2207/jjws.78.139 ↗
18. A. Demizu, H. Matsuda, Y. Fujino, Y. Ito, Cheng Zhao: J. Struct. Eng., vol. 58A, 2012, pp.40–49.
19. S. Okano, K. Matsushita, M Mochizuki, M. Toyoda: Weld. Int., vol. 28(3), 2012, pp.272–80.
20. T. Terasaki, D. Yamakawa: J. Jpn. Soc. Nav. Archit. Ocean Eng., vol.194, 2003, pp.211–17.10.2534/jjasnaoe1968.2003.194_211 ↗