journal article·2010-01

RETRACTED ARTICLE: Mechanical Properties of Uncoated and Aluminide-Coated René 80

Kh. Rahmani, S. Nategh

This record is marked as retracted by the source. Review the publisher’s notice before using its findings.
Publisher page

Abstract

Nickel-base superalloys such as René 80 are widely used in manufacturing aircraft turbine blades. They are usually coated in order to increase their wear, oxidation, erosion, and hot corrosion properties against environmental degradation. In this article, the mechanical behavior (tensile and low-cycle fatigue (LCF)) of uncoated and aluminide-coated (CODEP-B) René 80 has been studied at 871 °C and 982 °C. Experimental results show that the tensile properties of coated specimens are relatively lower than those of uncoated ones in the same conditions, but application of coating increases the LCF life of René 80 at T = 871 °C, 982 °C, R = (ε min/ε max) = 0, strain rate of 2 × 10−3 s−1, and Δε t = 0.8 pct. Scanning electron microscopy (SEM) studies of coated specimens at N = Nf show that the nucleation of cracks occurs merely in substrate, but cracks start from the surfaces in uncoated specimens. Transmission electron microscopy (TEM) investigations have been performed on fractured uncoated specimens to evaluate the microstructures at different temperatures. The misfit dislocation, pair dislocations, and cutting of γ′ were observed at T = 871 °C and 982 °C. The TEM studies also showed that at 982 °C stacking fault was observed in γ′ particles.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. P. Senechal: High Temp. Alloys Gas Turbine, 1982, p. 273.10.1007/978-94-009-7907-9_11 ↗
2. E.V. Zoretsky and R.C. Hendrick: Int. J. Rotat. Mach., 2003, vol. 9, p. 313.
3. S. Stekovic: ASME Int. Congr., International Mechanical Engineering Congress and Exposition, Orlando, FL, Nov. 5–11, 2005, p. 235. ISBN #: 0791837696
4. M. Naeem, R. Singh, and D. Probert: Int. J. Fatigue, 1999, vol. 21, p. 831.10.1016/S0142-1123(99)00025-0 ↗
5. M.I. Wood: Surf. Coat. Technol., 1989, vols. 39–40, p. 29.10.1016/0257-8972(89)90038-8 ↗
6. A. Strong and E. Lang: High Temperature Alloys for Gas Turbines 1982, Liege, Belgium, Oct. 4–6, 1982, D. Reidel Publishing Co., 1982, p. 469.10.1007/978-94-009-7907-9_19 ↗
7. T.C. Totemeier and J.E. King: Metall. Mater. Trans. A, 1996, vol. 27A, p. 353.10.1007/BF02648412 ↗
8. T.C. Totemeier, W.F. Gale, and J.E. King: Metall. Mater. Trans. A, 1996, vol. 27A, p. 363.10.1007/BF02648413 ↗
9. Y. Itoh, M. Saitoh, and Y. Ishiwata: J. Mater. Sci., 1999 p. 3957.10.1023/A:1004643311001 ↗
10. D. Vogel, L. Newman, P. Deb, and D.H. Boone: Mater. Sci. Eng. A, 1987, vol. 88, p. 227.10.1016/0025-5416(87)90089-9 ↗
11. Y.H. Zhang, D.M. Knowles, and P.J. Withers: Scripta Mater., 1997, vol. 37, p. 815.10.1016/S1359-6462(97)00156-5 ↗
12. M. Eskner and R. Sandstron: Surf. Coat. Technol., 2003, vol. 165, p. 21.10.1016/S0257-8972(02)00702-8 ↗
13. M. Eskner: Ph.D. Thesis, Royal Institute of Technology, Stockholm, 2004.
14. H.W. Grunling, K. Sceneider, and L. Singhelser: Mater. Sci. Eng. A, 1987, vol. 88, p. 177.10.1016/0025-5416(87)90083-8 ↗
15. J. Kameda, T.E. Bloomer, Y. Sugita, A. Ito, and S. Sakurai: Mater. Sci. Eng. A, 1997, vol. 229, p. 42.10.1016/S0921-5093(97)00003-8 ↗
16. H.J. Kolkman: Mater. Sci. Eng. A, 1987, vol. 89, p. 81.10.1016/0025-5416(87)90252-7 ↗
17. K. Rahmani and S. Nategh: Surf. Coat. Technol., 2008, vol. 202, p. 1385.10.1016/j.surfcoat.2007.06.041 ↗
18. P.A. Domas and S.D. Antolovich: Eng. Fract. Mech., 1985, vol. 21, p. 203.10.1016/0013-7944(85)90065-7 ↗
19. S.D. Antolovich and R. Baur: Metall. Trans. A, 1981, vol. 12A, p. 473.10.1007/BF02648545 ↗
20. J. Safari: Ph.D. Thesis, Materials Science and Engineering Department, Sharif University of Technology, Tehran, Iran, 2005.
21. S. Antolovich, P. Domas, and J.L Strudel: Metall. Trans. A, 1979, vol. 10A, p. 1859.10.1007/BF02811730 ↗
22. W.H. Chang: Superalloy, 1972, p. 636.
23. J.H. Zhang, Z.Q. Hu, Y.B. Xu, and Z.G. Wang: Metall. Trans. A, 1992, vol. 23A, p. 1253.10.1007/BF02665056 ↗
24. S.K. Hwang, H.N. Lee, and B.H. Yoon: Metall. Trans. A, 1989, vol. 20A, p. 2793.10.1007/BF02670171 ↗
25. S.D. Antolovich and E. Rosa: Mater. Sci. Eng. A, 1981, vol. 47, p. 47.10.1016/0025-5416(81)90040-9 ↗
26. V. Brien and B. Decamps: Mater. Sci. Eng. A, 2001, vol. 316, p. 18.10.1016/S0921-5093(01)01235-7 ↗
27. F. Liu, Y.C. Wang, H. Zhang, S.H. Ai, and Z.G. Wang: Mater. Sci. Technol., 2003, vol. 19, p. 853.10.1179/026708303225010786 ↗
28. H. Zhou, Y. Ro, H. Harada, Y. Aoki, and M. Arai: Mater. Sci. Eng. A, 2004, vol. 381, p. 20.10.1016/j.msea.2004.04.051 ↗
29. G. Sauthoff: Intermetallics, VCH Publishers, New York, NY, 1995, p. 57.10.1002/9783527615414 ↗
30. K. Rahmani and S. Nategh: Mater. Sci. Eng. A, 2008, vol. 486, p. 686.10.1016/j.msea.2007.09.062 ↗
31. K. Rahmani and S. Nategh: Mater. Des., 2009, vol. 30, p. 1183.10.1016/j.matdes.2008.06.064 ↗
32. K. Rahmani and S. Nategh: Mater. Sci. Eng. A, 2008, vol. 494, p. 385.10.1016/j.msea.2008.04.067 ↗
33. J. Auerswald, D. Mudherji, W. Chen, and R.P Wahi: Z. Metallkd., 1977, vol. 88, p. 652.
34. F. Jiao, D. Bettge, W. Osterle, and J. Ziebs: Acta Mater., 1996, vol. 10, p. 3933.10.1016/S1359-6454(96)00050-X ↗
35. Y. Tamarin: Protective Coatings for Turbine Blades, ASM INTERNATIONAL, Materials Park, OH, 2002.