Nanoindentation Round Robin on Thin Film Copper on Silicon
Source abstract
Abstract
Nanoindentation is used in a variety of fields to measure material hardness and elastic modulus. This test technique is especially attractive for thin films because of the difficulty of conducting tensile or other conventional mechanical characterization tests on thin film specimens, and because it requires only a small surface area for testing. However, the standardization process for this new measurement method is still in progress. To test the ability of current measurement procedures to provide comparable results, a round robin was conducted. Invitations to participate were sent to over 100 laboratories. Two specimens, a copper film on a silicon substrate and an uncoated substrate, were distributed to each of 33 laboratories. The choice of measurement procedure was left to the performing organizations. By the end of the reporting period, 27 sets of results were received. While the average reported uncertainty (1 standard deviation) among the individual participants was 4 pct of the average hardness, the interlaboratory standard deviation of the hardness values was 15 pct. Similarly, the average reported uncertainty of the modulus was 5 pct of the average value, but the interlaboratory standard deviation of the modulus was 19 pct. None of the measurement variables examined in this round robin, including instrument type, analysis procedure, time since instrument calibration, chip mounting procedure, and tip condition, and neither of the potential covariant effects, chip location in the wafer and test date, were found to have a statistically significant effect on the reported hardness or modulus.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Integrated Circuits and Semiconductor Failure Analysis · Force Microscopy Techniques and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Oliver W.C., Pharr G.M. (1992) J. Mater. Res., 7(6): 1564-8310.1557/JMR.1992.1564 ↗
2. Oliver W.C., Pharr G.M. (2004) J. Mater. Res., 19(1): 3-2010.1557/jmr.2004.19.1.3 ↗
3. Kriese M.D., Gerberich W.W., Moody N.R. (1999) J. Mater. Res. 14(7): 3007-1810.1557/JMR.1999.0404 ↗
4. Suresh S., Giannakopoulos A.E. (1998) Acta Mater. 46(16): 5755-6710.1016/S1359-6454(98)00226-2 ↗
5. Oliver W.C., Pharr G.M. (1992) MRS Bull. 17(7): 28-3310.1557/S0883769400041634 ↗
6. VanLandingham M.R. (2003) J. Res. Nat. Inst. Standards Technol. 108(4): 249-26510.6028/jres.108.024 ↗
7. Pratt J.R., Kramar J.A., Newell D.B., Smith D.T. (2005) Meas. Sci. Technol. 16(11): 2129-213710.1088/0957-0233/16/11/002 ↗
8. N.M. Jennett and J. Meneve: Materials Research Society Symp. Proc., N.R. Moody, W.W. Gerberich, N. Burnham, and S.P. Baker, eds., Materials Research Society, Warrendale, PA, 1998, vol. 522, pp. 239-44.10.1557/PROC-522-239 ↗
9. N.M. Jennett and A.J. Bushby: Materials Research Society Symp. Proc., C.S. Ozkan, L.B. Freund, R.C. Cammarata, and H. Gao, eds., Materials Research Society, Warrendale, PA, 2002, vol. 695, pp. 73-78.
10. “Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters,” ISO 14577-1, International Organization for Standards, Geneva, Switzerland, 2002.
11. “Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters–Part 2: Verification and Calibration of Testing Machines,” ISO 14577-2, International Organization for Standards, Geneva, Switzerland, 2002.
12. “Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters–Part 3: Calibration of Reference Blocks,” ISO 14577-3, International Organization for Standards, Geneva, Switzerland, 2002.
13. “Metallic Materials—Instrumented Indentation Test for Hardness and Materials Parameters–Part 4: Test Method for Metallic and Non- Metallic Coatings,” ISO/DIS 14577-4, International Organization for Standards, Geneva, Switzerland, 2002.
14. Tsui T.Y., Pharr G.M. (1999) J. Mater. Res. 14(1): 292-30110.1557/JMR.1999.0042 ↗
15. Kramer D.E., Volinsky A.A., Moody N.R., Gerberich W.W. (2001) J. Mater. Res. 16(11): 3150-5710.1557/JMR.2001.0434 ↗
16. Dieter G. (1986) Mechanical Metallurgy. McGraw-Hill, New York, NY, pp. 189-91
17. Tabor D. (1951) The Hardness of Metals. Oxford University Press, Oxford United Kingdom, pp. 105-06
18. “Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method,” ASTM E 691-99, ASTM International, West Conshohocken, PA, 2004.
19. Bahr D.F., Woodcock C.L., Pang M., Weaver K.D., Moody N.R. (2003) Int. J. Fract. 119(4): 339-4910.1023/A:1024979030155 ↗
20. Cheng Y.-W., Read D.T., McColskey J.D., Wright J.E. (2005) Thin Solid Films 484(1–2): 426-43210.1016/j.tsf.2005.03.030 ↗
21. D.T. Read, R. Geiss, J. Ramsey, T. Scherban, G. Xu, G.J. Blaine, B. Miner, and R.D. Emery: Materials Research Society Symp. Proc., D.F. Bahr, ed., Materials Research Society, Warrendale, PA, 2003, vol. 778, pp. 93-98.10.1557/PROC-778-U4.3 ↗
22. Read D.T., Cheng Y.-W., Keller R.R., McColskey J.D. (2001) Scripta Mater. 45(5): 583-58910.1016/S1359-6462(01)01067-3 ↗