journal article·2003-05

Effects of tensile prestrain on the notch toughness of low-alloy steel

J. H. Chen, G. Z. Wang, Z. Li

Publisher page

Abstract

Composition of the steel is shown in Table I. It is a clean steel with an elaborate refining process. Two types of heat treatments were carried out on the steel for obtaining desired microstructures and grain sizes. One was to heat the steel to 1000 °C for 6 hours, followed by a furnace cool. The microstructure, designated CG, contains ferrite grains with about 7 pct pearlite colonies and a few carbide particles, as shown in Figure 1. The histograms of size distributions of ferrite grains, pearlite colonies, and carbide particles are shown in Figure 2. The largest grain size corresponds to those in the coarse grain region of the welding heat-affected zone (HAZ) with a heat input of 3 kJ/mm. For comparison, the second heat treatment consisted of 945 °C/45 min, followed by a furnace cool. The grain sizes are finer and the microstructure is designated as FG. Related histograms are shown in Figures 3 and 4. As shown by these figures, the sizes of microstructures of both steels are much larger than those of conventional steels, even though the microscopic sizes of FG are smaller than those of CG. The deliberately coarsened grain microstructures and subsequent prestraining were adopted for simulating the thermal-strain behavior of the coarse grain region in the welding HAZ with a heat input of 3 kJ/mm. B. Specimens
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. C.J. Osborn, A.F. Scotchbrook, R.D. Stout, and B.G. Johnston: Welding J., 1949, vol. 28, pp. 337s-53s.
2. E.J. Ripling and W.M. Baldwin, Jr.: Trans. ASM, 1951, vol. 43, pp. 778–810.
3. F.W. Bridgman: in Studies in Large Plastic Flow and Fracture, Part III, McGraw-Hill, New York, NY, 1952, pp. 293–338.
4. W.T. Lankford: Welding J., 1956, vol. 35, pp. 195s-206s.
5. G.E. Turner: J. Iron Steel Inst., 1961, vol. 197, pp. 131–35.
6. J. Dvorak: Welding J., 1966, vol. 45, pp. 235s-40s.
7. N.J. Petch and R.W. Armstrong: Acta Metall., 1989, vol. 37, pp. 2279–85.10.1016/0001-6160(89)90155-7 ↗
8. P.M. Lorenz: Trans. ASM, 1961, vol. 54, pp. 466–80.
9. J.H. Chen, V.B. Wang, G.Z. Wang, and X. Chen: Eng. Fract. Mech., 2001, vol. 68, pp. 1669–86.10.1016/S0013-7944(01)00051-0 ↗
10. J.H. Chen, H.J. Wang, G.Z. Wang, Z.Q. Dong, and X. Chen: Int. J. Fract., 2002, vol. 117, pp. 375–92.10.1023/A:1022251128300 ↗
11. M.G. Mendiratta, R.L. Goetz, and D.M. Dimiduk: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3903–12.10.1007/BF02595639 ↗
12. G.Z. Wang and J.H. Chen: Int. J. Fract., 1998, vol. 89 (3), pp. 269–84.10.1023/A:1007464126165 ↗
13. G. Oates and J.R. Griffiths: Met. Sci. J., 1969, vol. 3 pp. 111–15.10.1179/msc.1969.3.1.111 ↗
14. T. Lin, A.G. Evans, and R.O. Ritchie: J. Mech. Phys. Solids, 1986, vol. 34, pp. 477–97.10.1016/0022-5096(86)90013-X ↗
15. J.H. Chen, G.Z. Wang, and H. Ma: Metall. Trans. A, 1990, vol. 21A, pp. 321–30.10.1007/BF02782412 ↗
16. G.Z. Wang and J.H. Chen: Int. J. Fract., 2001, vol. 108 (3), pp. 235–50.10.1023/A:1011033208335 ↗
17. J.H. Chen, L. Zhu, and H. Ma: Acta Metall. Mater. A, 1990, vol. 38, pp. 2527–35.10.1016/0956-7151(90)90264-H ↗
18. J.F. Knott, J. Iron Steel Inst., 1966, vol. 104, pp. 104–11.
19. A.S. Tetelman, T.R. Wilshaw, and C.A. Rau, Jr.: Int. J. Fract. Mech., 1968, vol. 4, pp. 147–57.10.1007/BF00188941 ↗
20. J.H. Chen, X.J. Hu, and G.Z. Wang: Fatigue Fract. Eng. Mater. Struct., 1996, vol. 19, pp. 807–19.10.1111/j.1460-2695.1996.tb01325.x ↗
21. D.A. Curry: Met. Sci., 1980, vol. 14, pp. 319–23.10.1179/msc.1980.14.8-9.319 ↗
22. T. Miyata, R.C. Yang, A. Otsuka, T. Haze, and S. Ahira: Advances in Fracture Research, Proc. ICF6, 1989, K Salama, K. Ravi-Chander, R. Taplin, and P. Rama Rao, eds., pp. 2563–72.
23. J.H. Chen, Y. Kikuta, T. Araki, M. Yoneda, and Y. Matsuda: Acta Metall., 1984, vol. 32, pp. 1779–88.10.1016/0001-6160(84)90234-7 ↗
24. J.J. Lewandowski and A.W. Thompson: Metall. Trans. A, 1986, vol. 17A, pp. 1769–86.10.1007/BF02817275 ↗
25. J.J. Lewandowski and A.W. Thompson: Metall. Trans. A, 1986, vol. 17A, pp. 461–72.10.1007/BF02643953 ↗
26. D.J. Alexander and I.M. Bernstein: Metall. Trans. A, 1989, vol. 20A, pp. 2321–35.10.1007/BF02666667 ↗
27. A.V. Samant and J.J. Lewandowski: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 398–99.
28. J.R. Griffiths and D.R.J. Owen: J. Mech. Phys. Solids, 1971, vol. 19, pp. 419–31.10.1016/0022-5096(71)90009-3 ↗
29. D.J. Alexander, J.J. Lewandowski, W.J. Sisak, and A.W. Thompson: J. Mech. Phys. Solids, 1986, vol. 34, pp. 433–54.10.1016/0022-5096(86)90011-6 ↗
30. J.J. Lewandowski and A.W. Thompson: Acta. Metall., 1987, vol. 35(7), pp. 1453–66.10.1016/0001-6160(87)90091-5 ↗
31. A.N. Stroh: Proceedings, Royal Society, New York, 1954, A233, pp. 400–32.
32. J.A. Hendrickson: Trans. ASM, 1958, vol. 50, pp. 656–76.
33. A.W. Thompson and J.F. Knott: Metall. Trans. A, 1993, vol. 24A, pp. 523–34.10.1007/BF02656622 ↗