journal article·2018-10

Microstructural Evolution and Mechanical Properties of CSEF/M P92 Steel Weldments Welded Using Different Filler Compositions

Nitin Saini, Manas Mohan Mahapatra, Rahul S. Mulik

Publisher page

Abstract

In the present investigation, P92 steel weld joints were prepared using a shielded metal arc welding (SMAW) process for two different fillers, E911 and P92. A comparative study was performed on the microstructural evolution, tensile strength, microhardness, and Charpy toughness across the P92 steel weldments in the as-welded and post-weld heat-treated (PWHT) conditions. The PWHT was performed at 760 °C for 2 hours. To study the effect of the different filler metals and PWHT on the mechanical properties, longitudinal and transverse tensile tests were carried out at room temperature for a constant cross-head speed of 1 mm/min. In the longitudinal direction, the tensile strength of the P92 steel welds was measured as 958 ± 35 and 1359 ± 38 MPa for the E911 and P92 filler, respectively. In the as-welded condition, the transverse tensile specimens were fractured from the fine-grained heat-affected zone or inter-critical heat-affected zone (FGHAZ/ICHAZ) and, after PWHT, the fracture location was shifted to over-tempered base metal from the FGHAZ/ICHAZ. After the PWHT, the tempering reaction resulted in lowering of the hardness throughout the weldment. After PWHT, the Charpy toughness of the weld fusion zone and heat-affected zone (HAZ) of the E911 filler weldments was measured as 66 ± 5 and 142 ± 8 J, respectively. The minimum required Charpy toughness of 47 J (EN1557: 1997) was achieved after the PWHT for both E911 and P92 filler.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. N. Saini, C. Pandey, and M.M. Mahapatra: Journal of Materials Engineering and Performance, 2017, vol. 26, pp. 5414–24.10.1007/s11665-017-2988-9 ↗
2. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Journal of Nuclear Materials, 2018, vol. 498, pp. 176–86.10.1016/j.jnucmat.2017.10.037 ↗
3. A. Zieliński: Journal of achievements in materials and manufacturing engineering, 2012, vol. 54, pp. 67–74.
4. A. Marek and J. Okrajni: Journal of Materials Engineering and Performance, 2014, vol. 23, pp. 31–8.10.1007/s11665-013-0744-3 ↗
5. N. Saini, C. Pandey, and M.M. Mahapatra: Int. J. Hydrog. Energy, 2017, pp. 1–11.
6. N. Saini, C. Pandey, M.M. Mahapatra, H.K. Narang, R.S. Mulik, and P. Kumar: Eng. Fail. Anal., 2017, pp. 1–9.
7. N. Saini, C. Pandey, M.M. Mahapatra, and R.S. Mulik: Materials Science and Engineering: A, 2018, vol. 711, pp. 37–43.10.1016/j.msea.2017.11.011 ↗
8. C.D. Lundin: Materials & Design, 1991, vol. 12, pp. 193–97.10.1016/0261-3069(91)90163-X ↗
9. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Journal of Alloys and Compounds, 2018, vol. 743, pp. 332–64.10.1016/j.jallcom.2018.01.120 ↗
10. J. Lecomte-Beckers, M. Carton, F. Schubert, and P.J. Ennis: Proceedings of the 8th Liege Conference Part I, 2006, vol. 53, pp. 1–631.
11. T. Sakthivel, M. Vasudevan, K. Laha, P. Parameswaran, K.S. Chandravathi, S. Panneer Selvi, V. Maduraimuthu, and M.D. Mathew: Materials Science and Engineering A, 2014, vol. 591, pp. 111–20.10.1016/j.msea.2013.10.071 ↗
12. R. Viswanathan, J. Sarver, and J.M. Tanzosh: Journal of Materials Engineering and Performance, 2006, vol. 15, pp. 255–74.10.1361/105994906X108756 ↗
13. T. Sakthivel, K. Laha, P. Parameswaran, S. Panneer Selvi, K.S. Chandravathi, and M.D. Mathew: Transactions of the Indian Institute of Metals, 2015, vol. 68, pp. 411–21.10.1007/s12666-014-0480-x ↗
14. K. Maruyama, K. Sawada, and J. Koike: ISIJ International, 2001, vol. 41, pp. 641–53.10.2355/isijinternational.41.641 ↗
15. N. Saini, C. Pandey, and M.M. Mahapatra: Materials Science & Engineering A, 2017, vol. 688, pp. 250–61.10.1016/j.msea.2017.02.022 ↗
16. E. Sambamurthy, S. Dutta, A.K. Panda, A. Mitra, and R.K. Roy: International Journal of Pressure Vessels and Piping, 2014, vol. 123–124, pp. 86–91.10.1016/j.ijpvp.2014.08.004 ↗
17. V. Sklenicka, K. Kucharova, M. Svobodová, M. Kvapilová, P. Král, and L. Horváth: Materials Characterization, 2016, vol. 119, pp. 1–12.10.1016/j.matchar.2016.06.033 ↗
18. M. Debicki, A.W. Marshall, Z. Zhang, G.B. Holloway, and H. Lane: in Welding and repair technology for power plants-5th International EPRI RRAC Conference, 2002, pp. 1–13.
19. C. Chovet, E. Galand, and B. Leduey: Welding in the World, 2008, vol. 52, pp. 18–26.10.1007/BF03266648 ↗
20. R. Bruscato: Weld. Res. Suppl., 1970, pp. 148–56.
21. C. Pandey, A. Giri, M.M. Mahapatra, and P. Kumar: Metals and Materials International, 2017, vol. 23, pp. 148–62.10.1007/s12540-017-6394-5 ↗
22. S.T. Mandziej, A. Výrostková, and C. Chovet: Welding in the World, 2011, vol. 55, pp. 37–51.10.1007/BF03321294 ↗
23. L. Falat, J. Kepic, L. Ciripova, P. Sevc, and I. Dlouhy: Journal of Materials Research, 2016, vol. 31, pp. 1532–43.10.1557/jmr.2016.134 ↗
24. J. Onoro: International Journal of Pressure Vessels and Piping, 2006, vol. 83, pp. 540–45.10.1016/j.ijpvp.2006.03.005 ↗
25. C. Pandey, M.M. Mahapatra, P. Kumar, N. Saini, J.G. Thakre, R.S. Vidyarthy, and H.K. Narang: Archives of Civil and Mechanical Engineering, 2018, vol. 18, pp. 713–22.10.1016/j.acme.2017.12.002 ↗
26. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Materials Science & Engineering A, 2018, vol. 712, pp. 720–37.10.1016/j.msea.2017.12.039 ↗
27. K.M. Chalk, P.H. Shipway, and D.J. Allen: Science and Technology of Welding & Joining, 2011, vol. 16, pp. 613–8.10.1179/1362171811Y.0000000042 ↗
28. W. Xue, Q. G. Pan, Y. Y. Ren, W. Shang, H. Q. Zeng, and H. Liu: Materials Science and Engineering A, 2012, vol. 552, pp. 493–50110.1016/j.msea.2012.05.076 ↗
29. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Materials Science and Engineering A, 2018, vol. 710, pp. 86–101.10.1016/j.msea.2017.10.086 ↗
30. H. Cerjak and E. Letofsky: Science and Technology of Welding and Joining, 1996, vol. 1, pp. 36–42.10.1179/stw.1996.1.1.36 ↗
31. M.R. Dodo, T. Ause, M.A. Adamu, and Y.M. Ibrahim, Niger. J. Tech., 2016, vol. 35, pp. 337-43.10.4314/njt.v35i2.14 ↗
32. N. Saini, C. Pandey, and M.M. Mahapatra: Trans. Indian Inst. Met., DOI: 10.1007/s12666-017-1145-3.10.1007/s12666-017-1145-3 ↗
33. C. Pandey and M.M. Mahapatra: Journal of Materials Engineering and Performance, 2016, vol. 25, pp. 2195–210.10.1007/s11665-016-2064-x ↗
34. ASTM E8/E8M-16a, ASTM International, West Conshohocken, PA, 2016.
35. AWS B4.0, American Welding Society, 2016.
36. C.G. Panait, A. Zielinska-Lipiec, T. Koziel, A. Czyrska-filemonowicz, A.F. Gourgues-Lorenzon, and W. Bendick: Materials Science & Engineering A, 2010, vol. 527, pp. 4062–69.10.1016/j.msea.2010.03.010 ↗
37. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Materials Science and Engineering: A, 2017, vol. 685, pp. 39–49.10.1016/j.msea.2016.12.079 ↗
38. D.R. Barbadikar, G.S. Deshmukh, L. Maddi, K. Laha, P. Parameswaran, A.R. Ballal, D.R. Peshwe, R.K. Paretkar, M. Nandagopal, and M.D. Mathew: International Journal of Pressure Vessels and Piping, 2015, vol. 132–133, pp. 97–105.10.1016/j.ijpvp.2015.07.001 ↗
39. C. Pandey, A. Giri, and M.M. Mahapatra: Materials Science and Engineering A, 2016, vol. 657, pp. 173–84.10.1016/j.msea.2016.01.066 ↗
40. T. Shrestha, S.F. Alsagabi, I. Charit, G.P. Potirniche, M. V Glazoff, and H.F. Lopez: Metals, 2015, vol. 5, pp. 131–49.10.3390/met5010131 ↗
41. Z. Zhang, G. Holloway, and A. Marshall: Weld. World, 2008, vol. 6, pp. 1–13.
42. B. Silwal, L. Li, A. Deceuster, and B. Griffiths: Welding Research, 2013, vol. 92, p. 80s–87s.
43. J. Cao, Y. Gong, K. Zhu, Z.G. Yang, X.M. Luo, and F.M. Gu: Materials and Design, 2011, vol. 32, pp. 2763–70.10.1016/j.matdes.2011.01.008 ↗
44. L. Milovic´, T. Vuherer, M. Vrhovac, and M. Stankovic: Mater. Des. 2013, vol. 46, pp. 660–7.10.1016/j.matdes.2012.10.057 ↗
45. C. Pandey, M.M. Mahapatara, P. Kumar, and N. Saini: Journal of Manufacturing Processes, 2018, vol. 31, pp. 247–59.10.1016/j.jmapro.2017.11.020 ↗
46. S.S. Wang, D.L. Peng, L. Chang, and X.D. Hui: Materials and Design, 2013, vol. 50, pp. 174–80.10.1016/j.matdes.2013.01.072 ↗
47. C. Pandey, M.M. Mahapatra, P. Kumar, and N. Saini: Materials Science & Engineering A, 2018, vol. 710, pp. 86–101.10.1016/j.msea.2017.10.086 ↗
48. C.G. Panait, W. Bendick, A. Fuchsmann, A.F. Gourgues-Lorenzon, and J. Besson: International Journal of Pressure Vessels and Piping, 2010, vol. 87, pp. 326–35.10.1016/j.ijpvp.2010.03.017 ↗
49. C. Pandey and M.M. Mahapatra: Transactions of the Indian Institute of Metals, 2016, vol. 69, pp. 1657–73.10.1007/s12666-015-0826-z ↗
50. C. Pandey, M.M. Mahapatra, P. Kumar, N. Saini, and J.G. Thakre: Trans. Indian Inst. Met. DOI: 10.1007/s12666-017-1215-6.10.1007/s12666-017-1215-6 ↗
51. B. Arivazhagan and M. Vasudevan: Journal of Manufacturing Processes, 2014, vol. 16, pp. 305–11.10.1016/j.jmapro.2014.01.003 ↗
52. C. Pandey, N. Saini, M.M. Mahapatra, and P. Kumar: Engineering Failure Analysis, 2016, vol. 71, pp. 131–47.10.1016/j.engfailanal.2016.06.012 ↗