journal article·2009-09

Residual Stresses in Inertia-Friction-Welded Dissimilar High-Strength Steels

R.J. Moat, D.J. Hughes, A. Steuwer, N. Iqbal, M. Preuss, S.E. Bray, M. Rawson

Publisher page

Abstract

The welding of dissimilar alloys is seen increasingly as a way forward to improve efficiencies in modern aeroengines, because it allows one to tailor varying material property demands across a component. Dissimilar inertia friction welding (IFW) of two high-strength steels, Aermet 100 and S/CMV, has been identified as a possible joint for rotating gas turbine components and the resulting welds are investigated in this article. In order to understand the impact of the welding process and predict the life expectancy of such structures, a detailed understanding of the residual stress fields present in the welded component is needed. By combining energy-dispersive synchrotron X-ray diffraction (EDSXRD) and neutron diffraction, it has been possible to map the variations in lattice spacing of the ferritic phase on both sides of two tubular Aermet 100-S/CMV inertia friction welds (as-welded and postweld heat-treated condition) with a wall thickness of 37 mm. Laboratory-based XRD measurements were required to take into account the variation in the strain-free d-spacing across the weld region. It was found that, in the heat-affected zone (HAZ) slightly away from the weld line, residual stress fields showed tensile stresses increasing most dramatically in the hoop direction toward the weld line. Closer to the weld line, in the plastically affected zone, a sharp drop in the residual stresses was observed on both sides, although more dramatically in the S/CMV. In addition to residual stress mapping, synchrotron XRD measurements were carried out to map microstructural changes in thin slices cut from the welds. By studying the diffraction peak asymmetry of the 200-α diffraction peak, it was possible to demonstrate that a martensitic phase transformation in the S/CMV is responsible for the significant stress reduction close to the weld line. The postweld heat treatment (PWHT) chosen to avoid any overaging of the Aermet 100 and to temper the S/CMV martensite resulted in little stress relief on the S/CMV side of the weld. © The Minerals, Metals & Materials Society and ASM International 2009.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. T. Ford: Aircraft Eng. Aerospace Technol., 1997, vol. 69, pp. 555–60.10.1108/00022669710186084 ↗
2. R.J. Moat, M. Karadge, M. Preuss, S. Bray, and M. Rawson: Mater. Process. Technol., 2004, vols. 1–3, pp 48–58.
3. K.K. Wang: Weld. Res. Coun. Bull., 1974, vol. 204, pp. 1–22.
4. C. Sudha: J. Nucl. Mater., 2002, vol. 302, pp. 193–205.10.1016/S0022-3115(02)00777-8 ↗
5. D.G. Lee, K.C. Jang, J.M. Kuk, and I.S. Kim: J. Mater. Process. Technol., 2004, vols. 155–156, pp. 1402–07.10.1016/j.jmatprotec.2004.04.400 ↗
6. Y.C. Kim, A. Fuji, and T.H. North: Mater. Sci. Technol., 1995, vol. 11, pp. 383–87.10.1179/mst.1995.11.4.383 ↗
7. H.Y. Li, Z.W. Huang, S. Bray, G. Baxter, and P. Bowen: Mater. Sci. Technol., 2007, vol. 23 (12), pp. 1408–18.10.1179/174328407X243933 ↗
8. O. Roder, J. Albrecht, and G. Lutering: Mater. High Temp., 2006, vol. 23 (3–4), pp. 171–77.10.3184/096034006782739259 ↗
9. Z.W. Huang, H.Y. Li, M. Preuss, M. Karadge, P. Bowen, S. Bray, and G. Baxter: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1608–20.10.1007/s11661-007-9194-6 ↗
10. C. Bennett, T.H. Hyde, and E.J. Williams: J. Mater. Des. Appl., 2007, vol. 221 (4), pp. 275–84.
11. W.S. Robotham, T.H. Hyde, E.J. Williams, P. Brown, I.R. McColl, and C.J. Kong: Appl. Mech. Mater. 2005, vols. 3–4, pp. 131–38.10.4028/www.scientific.net/AMM.3-4.131 ↗
12. H. Ochi, K. Ogawa, Y. Yamamoto, and Y. Suga: Int. J. Offshore Polar Eng., 1998, vol. 9 (2), pp. 541–46.
13. M.D. Tumuluru: Weld. Res. Suppl., 1984, vol. 9, pp. 289–94.
14. M. Preuss, L.W.L. Pang, P.J. Withers, and G. Baxter: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3227–34.10.1007/s11661-002-0308-x ↗
15. L. Wang, M. Preuss, P.J. Withers, G. Baxter, and P. Wilson: J. Neut. Res., 2004, vol. 12 (1–3), pp. 21–25.10.1080/10238160410001734405 ↗
16. M. Preuss, P.J. Withers, and G. Baxter: Mater. Sci. Eng., A, 2006, vol. 437 (1), pp. 38–45.10.1016/j.msea.2006.04.058 ↗
17. J.W.L. Pang, M. Preuss, P.J. Withers, G. Baxter, and C. Small: Mater. Sci. Eng., A, 2003, vol. 356 (1–2), pp. 405–13.10.1016/S0921-5093(03)00153-9 ↗
18. P.J. Bouchard and P.J. Withers: J. Neut. Res., 2004, vol. 12, pp. 39–44.10.1080/10238160410001734432 ↗
19. J.A. Francis, H.K.D.H. Bhadeshia, and P.J. Withers: Mater. Sci. Technol., 2007, vol. 23 (9), pp. 1009–20.10.1179/174328407X213116 ↗
20. Aermet 100 Data Sheet, Carpenter Technology Corporation, Wyomissing, PA, 09/01/1995.
21. R. Ayer and P.M. Machmeier: Metall. Trans. A, 1993, vol. 24A, pp. 1943–55.10.1007/BF02666329 ↗
22. M. Grujick: Mater. Sci. Eng., A, 1990, vol. 128, pp. 201–07.10.1016/0921-5093(90)90228-U ↗
23. G.R. Speich, D.S. Dabkowski, and L.F. Porter: Metall. Trans. A, 1973, vol. 4, pp. 303–15.10.1007/BF02649630 ↗
24. M.D. Perkas, P.L. Gruzin, A.F. Edneral, B.M. Mogutnov, Y.L. Rodionov, and M.A. Eremenko: Mater. Sci. Heat Treat ., 1985, vol. 27 (5), pp. 350–56.10.1007/BF00693375 ↗
25. A. Steuwer, J.R. Santisteban, M. Turski, P.J. Withers, and T. Buslaps: Nucl. Instrum. Methods Phys. Res., Sect. B, 2005, vol. 238 (1–4), pp. 200–04.10.1016/j.nimb.2005.06.049 ↗
26. J. Altenkirch, A. Steuwer, M. Peel, D.G. Richards, and P.J. Withers: Mater. Sci. Eng., A, 2008, vol. 488 (1–2), pp. 16–24.10.1016/j.msea.2007.10.055 ↗
27. A.C. Larson and R.B. Von Dreele: Los Alamos National Laboratory Report No. LAUR 86-748, Los Alamos National Laboratory, Los Alamos, NM, 2000, http://www.ncnr.nist.gov/xtal/software/gsas.html
28. B.H. Toby: J. Appl. Crystallogr., 2001, vol. 34, pp. 210–13.10.1107/S0021889801002242 ↗
29. L. Edwards, P.J. Bouchard, M. Dutta, D.Q. Wang, J.R. Santistiban, S. Hiller, and M.E. Fitzpatrick: Int. J. Press. Vess. Pip., 2005, vol. 82 (4), pp. 288–98.10.1016/j.ijpvp.2004.08.007 ↗
30. T. Pirling, G. Bruno, and P.J. Withers: Mater. Sci. Forum, 2006, vols. 524–52, pp. 217–22.10.4028/www.scientific.net/MSF.524-525.217 ↗
31. A.P. Hammersley: “Fit2D: An Introduction and Overview”, Internal Report ESRF-97-HA02T, 1997, pp. 1–319, http://www.esrf.fr/computing/scientific/FIT2D/FIT2D_REF/fit2d_r.html.
32. “ASTM E 975-03: Standard Practice for X-Ray Determination of Retained Austenite in Steel with Near Random Crystallographic Orientation,” Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2003.
33. B.R. Kowalski: Chemometrics, Mathematics and Statistics in Chemistry, D. Reidel, Dordrecht, Holland,1984.
34. I.C. Noyan and J.B. Cohen: Residual Stress, Measurement by Diffraction and Interpretation, Springer-Verlag, Berlin, 1987.
35. P.J. Withers, M. Preuss, A. Steuwer, and J.W.L. Pang: J. Appl. Crystallogr., 2007, vol. 40 (5), pp. 891–904.10.1107/S0021889807030269 ↗
36. J.W.L. Pang, T.M. Holden, and T.E. Mason: J. Strain Anal., 1998, vol. 33 (5), pp. 373–83.10.1243/0309324981513075 ↗
37. J.F. Breedis and W.D. Robertson: Acta Metall., 1963, vol. 11, pp. 547–59.10.1016/0001-6160(63)90089-0 ↗