journal article·2005-09

Influence of spraying conditions on microstructures of Al-SiC p composites by plasma spraying

Manchang Gui, Suk Bong Kang, Kwangjun Euh

Publisher page

Abstract

Air plasma spraying was used to produce Al-SiCp composites as electronic packaging material. Ballmilled Al with 55 and 75 vol. pct SiC powders was repeatedly deposited onto a graphite substrate, and then mechanically removed to get free-standing 100 × 100 mm composite plates of about 2-mm thickness. Different input electrical powers were employed at two spray distances of 100 and 120 mm. The SiC volume fraction and porosity in the sprayed composites were found to be dependent on spray conditions, especially input electrical power. Maximal SiC volume fraction can be obtained at a low input electrical power for the composite sprayed from the Al-55SiC powder and a high input electrical power for Al-75SiC powder. The variation of the SiC level in the composites with spray conditions and SiC size is discussed based on the characteristic of feedstock, the characteristic of deposited surface, and the heat and momentum transfer between particle and plasma flame. Pores in the sprayed composites were found inside one sprayed layer (inner-layer pore) and at the boundary between two sprayed layers (interlayer pore). The formation mechanisms of two types of pores are also explained. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses indicate that Si phase is formed in the sprayed composites for most spray conditions. The Si resulted from the decomposition of SiC particles in high-temperature plasma flame.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. C. Zweben: JOM, 1992, vol. 44 (7), pp. 15–23.10.1007/BF03222270 ↗
2. R.F. Jeffries and D.J. Burrows: GEC J. Res., 1994, vol. 11 (3), pp. 150–66.
3. M.K. Premkumar, W.H. Hunt, and R.R. Sawtell, Jr.: JOM, 1992, vol. 44 (7), pp. 24–28.10.1007/BF03222271 ↗
4. R.M. German, K.F. Hens, and J.L. Johnson: Int. J. Powder Metall., 1994, vol. 30, pp. 205–15.
5. C. Zweben: Electron. Cooling, 1999, vol. 5 (3), pp. 36–42.
6. S. Sampath and H. Herman: JOM, 1993, vol. 45 (7), pp. 42–49.10.1007/BF03222381 ↗
7. M.C. Gui and S.B. Kang: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2383–92.10.1007/s11661-001-0212-9 ↗
8. A. Iiyuschenko, P. Vityaz, V. Okovity, A. Verstak, E. Lugscheider, and P. Remer: in Advances in Thermal Spray Science and Technology, C.C. Berndt and S. Sampath, eds., ASM INTERNATIONAL, Materials Park, OH, 1995, pp. 317–20.
9. R.L. Deuis and C. Subramanian: Mater. Sci. Technol., 2000, vol. 16, pp. 209–19.10.1179/026708300101507569 ↗
10. B. Wielage, S. Steinhauser, T. Schnick, and D. Nickelmann: J. Thermal Spray Technol., 1999, vol. 8, pp. 553–58.10.1361/105996399770350241 ↗
11. K.A. Khor, F.Y.C. Boey, Y. Murakoshi, and T.J. Sano: J. Thermal Spray Technol., 1994, vol. 3, pp. 162–68.10.1007/BF02648273 ↗
12. K. Ghosh, T. Troczynski, and A.C.D. Chaklader: J. Thermal Spray Technol., 1998, vol. 7, pp. 78–86.10.1361/105996398770351070 ↗
13. B. Wielage, K. Fleisher, and G. Zimmerman: in Thermal Spray: Practical Solutions for Engineering Problems, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 1996, p. 349.
14. M.C. Gui and S.B. Kang: Mater. Lett., 2000, vol. 46, pp. 296–302.10.1016/S0167-577X(00)00191-9 ↗
15. M.E. Smagorinski, P.G. Tsantrizos, S. Grenier, A. Cavasin, and G. Kim: Mater. Sci. Eng. A, 1998, vol. 244, pp. 86–90.10.1016/S0921-5093(97)00830-7 ↗
16. T. Itsukaichi, T.W. Eagar, M. Umemoto, and I. Okane: Welding Res. Suppl., 1996, vol. 9, pp. 285s-296s.
17. R. Angers, M.R. Krishnadev, R. Tremblay, J.F. Corriveau, and D. Dube: Mater. Sci. Eng. A, 1999, vol. 262, pp. 9–15.10.1016/S0921-5093(98)01030-2 ↗
18. L. Lu, M.O. Lai, and S. Zhang: Key Eng. Mater., 1995, vols. 104–107 (1), pp. 111–24.10.4028/www.scientific.net/KEM.104-107.111 ↗
19. M.C. Gui, S.B. Kang, and K. Euh: J. Thermal Spray Technol., 2004, vol. 13, pp. 537–43.10.1361/10599630421451 ↗
20. S.V. Joshi and R. Sivakumar: Mater. Sci. Technol., vol. 8, 1992, pp. 481–88.10.1179/mst.1992.8.6.481 ↗
21. M. Vardelle, A. Vardelle, P. Fauchais, and M.I. Boulos: AIChE J., 1983, vol. 29, pp. 236–43.10.1002/aic.690290210 ↗
22. J.M. Lee, S.B. Kang, T. Sato, H. Tezuka, and A. Kamio: Mater. Lett., 2002, vol. 57, pp. 812–17.10.1016/S0167-577X(02)00878-9 ↗
23. R.W. Olesnski and G.J. Abbaschian: in Binary Alloy Phase Diagrams, T.B. Massaliski, ed., 2nd ed., ASM INTERNATIONAL, Materials Park, OH, 1990, vol. I, pp. 882–83.