Homogenization of EN AW 6005A Alloy for Improved Extrudability
Source abstract
Abstract
The homogenization practice for EN AW 6005A was investigated. It requires an 8-hour soaking at 853 K (580 °C) to even out the Mg and Si distribution in the aluminum matrix and to fully transform the monoclinic β-Al5FeSi plates into relatively small round αc-Al12(Fe,Mn)3Si particles with a “necklace” type configuration. It is predominantly the equilibrium β-Mg2Si phase that precipitates during subsequent cooling at 1000 K h−1 while orthogonal β′-Mg2Si platelets are also noted starting at 500 K h−1. The hardness decreases with decreasing cooling rate from 41.1 ± 1 HV to 35.8 ± 0.8 HV, by 15 pct, over the range investigated. The precipitation capacity retained in homogenized samples cooled to room temperature at less than 250 K h−1 is reduced substantially. The solvus temperatures of these samples are below 773 K (500 °C) ensuring full solutionizing of the Mg2Si precipitates below the press exit temperatures typically employed by extruders. An 8-hour soaking at 853 K (580 °C) followed by cooling at 250 K h−1 is identified to be the optimum homogenization treatment as it gives a homogeneous structure with predominantly spherical-shaped αc-Al12(Fe,Mn)3Si particles and sufficiently low hardness for improved extrudability and a solvus temperature below 773 K (500 °C) to ensure adequate age-hardening capacity.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. E.C. Beatty: Proc. 1st Int. Aluminum Extrusion Technology Seminar, Paper No. 10, 1969.
2. B. Rinderer, Mater. Sci. Forum, 2011, vol.693, pp. 264-75.10.4028/www.scientific.net/MSF.693.264 ↗
3. Y. Birol, J. Mater. Process Tech., 2004, vol. 148, pp. 250-8.10.1016/j.jmatprotec.2004.01.056 ↗
4. S.R. Claves, D.L. Elias, W.Z. Misiolek, Mater. Sci. Forum, 2002, vol. 396-402, pp. 667-74.10.4028/www.scientific.net/MSF.396-402.667 ↗
5. S. Zajac, B. Hutchinson, A. Johansson, L.O. Gullman: Mater. Sci. Technol., 1994, vol. 10, pp. 323-33.10.1179/mst.1994.10.4.323 ↗
6. E.C. Beatty: Proc. 2nd Int. Aluminum Extrusion Technology Seminar 1, 1977, pp. 225–28.
7. J. Langerweger: Proc. Conf. on Aluminium Technology, 1986, pp. 216–22.
8. K. Karhausen, A.L. Dons, and T. Aukrust: Mater. Sci. Forum, 1996, vol. 217–222, pp. 403–08.10.4028/www.scientific.net/MSF.217-222.403 ↗
9. T. Oka, M. Yanagawa, and M. Hirano: Proc. 6th Int. Aluminum Extrusion Technology Seminar 1, 1996, pp. 157–63.
10. N.C.W. Kuijpers, W.H. Kool, S. van der Zwaag (2002) Mater. Sci. Forum 396-402:675–680.10.4028/www.scientific.net/MSF.396-402.675 ↗
11. H. Tanihata, T. Sugawara, K. Matsuda, and S. Ikeno: J. Mater. Sci., 1999, vol. 34, pp. 1205–10.10.1023/A:1004504805781 ↗
12. J. Langerweger: Aluminum, 1982, vol. 58, pp. 107–09.10.1111/j.1475-4932.1982.tb00354.x ↗
13. O. Reiso: Mater. Sci. Forum, 2004, vol. 28, pp. 32–46.10.2304/forum.2004.46.1.6 ↗
14. E.B. Bjornbakk: Mater. Sci. Forum, 2002, vol. 396–402, pp. 405–10.10.4028/www.scientific.net/MSF.396-402.405 ↗
15. M. Lefstad and O. Reiso: Proc. 6th Int. Aluminum Extrusion Technology Seminar, 1996, vol. 1, pp. 11–21.
16. N. Dahl, T. Johnsen, B.R. Henriksen, and E.K. Jensen: Proc. 6th Int. Aluminum Extrusion Technology Seminar, 1996, vol. 1, pp. 529–35.
17. S. Zajac, B. Bengtsson, and C. Jonsson: Mater. Sci. Forum, 2002, vol. 396–402, pp. 399–04.10.4028/www.scientific.net/MSF.396-402.399 ↗
18. http://www.eaa.net, 2004-01-28, The European Aluminium Association.
19. Y. Birol: Mater. Charact., 2012, http://dx.doi.org/10.1016/j.matchar.2012.07.015.10.1016/j.matchar.2012.07.015 ↗
20. N.C.W. Kuijpers, J. Tirel, D.N. Hanlon, and S. Zwaag: Mater. Charact., 2002, vol. 48, pp. 379–92.10.1016/S1044-5803(02)00289-9 ↗
21. G.M. Novotnik and J. Sieniawski: J. Mater. Process Technol., 2005, vol. 162–163, pp. 367–72.10.1016/j.jmatprotec.2005.02.115 ↗
22. J.R. Davis, Aluminum and Aluminum Alloys, ASM Specialty Handbook, ASM International, Materials Park, OH, 1996.
23. H. Tanihata, T. Sugawara, K. Matsuda, and S.J. Ikeno: J. Mater. Sci., 1999, vol. 34, pp. 1205–10.10.1023/A:1004504805781 ↗
24. N.C.W. Kuijpers, W.H. Kool, P.T.G. Koenis, K.E. Nilsen, I. Todd, and S. van der Zwaag: Mater. Charact., 2003, vol. 49, pp. 409–20.10.1016/S1044-5803(03)00036-6 ↗
25. P. Donnadieu, G. Lapasset, and T.H. Sanders: Philos. Mag. Lett., 1994, vol. 70, pp. 319–26.10.1080/09500839408240993 ↗
26. S. Zajac, L.O. Gullman, A. Johansson, and B. Bengtsson: Mater. Sci. Forum, 1996, vol. 217–222, pp. 1193–98.10.4028/www.scientific.net/MSF.217-222.1193 ↗
27. G.A. Edwards, K. Stiller, G.L. Dunlop, and M.J. Couper: Acta Mater., 1998, vol. 46, pp. 3893–04.10.1016/S1359-6454(98)00059-7 ↗
28. W.F. Miao and D.E. Laughlin: Scr. Mater., 1999, vol. 40, pp. 873–78.10.1016/S1359-6462(99)00046-9 ↗
29. A.K. Gupta, D.J. Lloyd, and S.A. Court: Mater. Sci. Eng., 2001, vol. 301A, pp. 140–46.
30. L. Zhuang, R.D. Haan, J. Bottema, C.T.W. Lahaye, and P.D. Smet: Mater. Sci. Forum, 2000, vol. 331–337, pp. 1309–14.10.4028/www.scientific.net/MSF.331-337.1309 ↗
31. A. Borrego and G. Gonzales Doncel: Mater. Sci. Eng., 1998, vol. 248A, pp. 10–18.10.1016/S0921-5093(97)00706-5 ↗
32. J.Y. Yao, D.A. Graham, B. Rinderer, and M.J. Couper: Micron, 2001, vol. 32, pp. 865–70.10.1016/S0968-4328(00)00095-0 ↗
33. C.D. Marioara, S.J. Andersen, J. Jansen and H.W. Zandbergen: Acta Mater., 2003, vol. 51, pp. 789–96.10.1016/S1359-6454(02)00470-6 ↗
34. K. Fukui, M. Takeda, and T. Endo: Mater. Lett., 2005, vol. 59, pp. 1444–48.10.1016/j.matlet.2004.12.049 ↗
35. K. Matsuda, Y. Sakaguchi, Y. Miyata, Y. Uteni, T. Sato, A. Kamio, and S. Ikeno: J. Mater. Sci., 2000, vol. 35, pp. 179–89.10.1023/A:1004769305736 ↗
36. Y. Birol: J. Therm. Anal. Calorim., 2008, vol. 93, pp. 977–81.10.1007/s10973-007-8686-3 ↗
37. Y. Birol: J. Therm. Anal. Calorim., 2006, vol. 83, pp. 219–22.10.1007/s10973-005-6950-y ↗