journal article·2007-01

Equilibrium Distribution of Liquid during Sintering of Assemblies of WC/Co Cermets

Christophe Colin, Vincent Guipont, Francis Delannay

Publisher page

Abstract

Assemblies were made by stacking on top of one another two cylinders of WC-Co cermets differing in mean WC particle size (relative size ratio of 3.5) and cobalt concentration (6 or 15 wt pct). These assemblies were bonded by heat treatment at 1400 °C under protective atmosphere for a dwell time of 7 hours. After completion of the heat treatment, the distributions of the cobalt concentration and WC grain size as a function of distance from the original interface between the two cermets were analyzed by combining Vickers microhardness measurements and image analysis. At equilibrium, the Co content was always larger on the side containing the smaller WC particle size. The final partition of Co was compared with the predictions of a model developed for expressing the dependence of the solid/solid and solid/liquid interface areas on the system parameters: phase volume fractions, dihedral angle, particle size, and particle coordination. An excellent agreement is found when assuming an average WC coordination of 7.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Mortensen A., Suresh S. (1995) Int. Mater. Rev., vol. 40, pp. 239–6510.1179/imr.1995.40.6.239 ↗
2. Lisovsky A.F., Babich M.M., (1972) Sov. Powder Metall. Met. Ceram., vol. 11, pp. 124–2810.1007/BF00814043 ↗
3. C. Colin, N. Favrot, G. Barbier, and F. Delannay: Proc. Coll. Les Traitements des Poudres et leurs Conséquences, SF2M, Paris, 1996, pp. 30–1–30–7
4. Fang Z., Lockwood G., Griffo A. (1999) Metall. Mater. Trans. A, vol. 30A, pp. 3231–3810.1007/s11661-999-0233-3 ↗
5. Fang Z., Griffo A., White B., Lockwood G., Belnap D., Hilmas G., Bitler J. (2001) Int. J. Refract. Met. Hard Mater., vol. 19, pp. 453–5910.1016/S0263-4368(01)00031-2 ↗
6. Cheng J., Wu Y., Xia Y. (2003) Mater. Sci. Forum, vols. 423–425, pp. 45–4810.4028/www.scientific.net/MSF.423-425.45 ↗
7. Eso O., Fang Z., Griffo A. (2005) Int. J. Refractory Met. Hard Mater., vol. 23, pp. 233–4110.1016/j.ijrmhm.2005.04.017 ↗
8. San Marchi C., Felberbaum L., Mortensen A. (2000) Metall. Mater. Trans. A, vol. 31A, pp. 397–40010.1007/s11661-000-0276-y ↗
9. Kipphut C.M., Bose A., Farooq S., German R.M. (1988) Metall. Trans. A, vol. 19A, pp. 1905–1310.1007/BF02645192 ↗
10. Fang Z., Eso O. (2005) Scripta Mater., vol. 52, pp. 785–9110.1016/j.scriptamat.2004.12.008 ↗
11. W.A. Kaysser, O.J. Kwon, and G. Petzow: P/M-82 Proc. Eur. Powder Metallurgy Conf., EPMA, 1982 pp. 23–30
12. Park H.-H., Yoon D.N. (1985) Metall. Trans. A, vol. 16A, pp. 923–2810.1007/BF02814844 ↗
13. Lisovsky A.F. (1990) Int. J. Heat Mass Transfer, vol. 33, pp. 1599–160310.1016/0017-9310(90)90016-N ↗
14. Colin C., Durant L., Favrot N., Besson J., Barbier G., Delannay F. (1993–1994) Int. J. Refractory Met. Hard Mater., vol. 12, pp. 145–5210.1016/0263-4368(93)90064-M ↗
15. Delannay F., Pardoen D., Colin C. (2005) Acta Mater., vol. 53, pp. 1655–6410.1016/j.actamat.2004.12.015 ↗
16. N. Favrot: Ph.D. Dissertation, Ecole nationale Supérieure des Mines de Paris, Paris, 1995
17. Gauthier G., Coster M., Chermant L., Chermant J.-L. (1996) Microsc. Microanalysis Microstruct., vol. 7, pp. 339–4410.1051/mmm:1996131 ↗
18. Put S., Vleugels J., Van der Biest O. (2001) Scripta Mater., vol. 45, pp. 1139–4510.1016/S1359-6462(01)01126-5 ↗
19. A.F. Lisovsky: Kiev Naukova Dumka, 1984
20. C.-E. Delaunay: J. Math. Pures Appl., 1841, Sér. 1, vol. 6, pp. 309–20
21. Delannay F. (2005) Phil. Mag., vol. 85, pp. 3719–3310.1080/14786430500318860 ↗
22. German R.M. (1985) Liquid Phase Sintering, Plenum Press, New York NY10.1007/978-1-4899-3599-1 ↗
23. Niemi A.N., Baxa L.E., Lee J.K., Courtney T.M. (1981) Modern Developments in Powder Metallurgy, Metal Powder Industries Federation, Princeton, NJ, vol. 12, pp. 483–95
24. Gurland J. (1959) Trans. TMS-AIME, vol. 215, pp. 601–08
25. Grathwohl G., Warren R. (1974) Mater. Sci. Eng., vol. 14, pp. 55–6510.1016/0025-5416(74)90123-2 ↗
26. Exner H.E. (1982) In: Viswanadham R.K., Rowcliffe D.J., Gurland J. (eds) Science of Hard Materials, Plenum Press, New York, NY, pp. 233–62
27. Sharma N.K., Ward I.D., Fraser H.L., Williams W.S. (1980) J. Am. Ceram. Soc., vol. 63, pp. 194–9610.1111/j.1151-2916.1980.tb10690.x ↗
28. Pastor H. (1984) Matér. Techn., vol. 12, pp. 433–5010.1051/mattech/198472120433 ↗
29. Froschauer L., Fulrath R.M. (1976) J. Mater. Sci., vol. 11, pp. 142–4910.1007/BF00541086 ↗
30. Exner H.E. (1979) Int. Met. Rev, vol. 24, pp. 149–7310.1179/095066079790136363 ↗
31. Lisovsky A.F. (1990) Int. J. Powder Metall., vol. 26, pp. 45–49
32. Lea C., Roebuck B. (1981) Met. Sci., vol. 15, pp. 262–6610.1179/msc.1981.15.6.262 ↗
33. Laugier M.T. (1985) J. Mat. Sci. Lett., vol. 4, pp. 263–6410.1007/BF00719785 ↗
34. Rautola P., Norton J.T. (1952) Trans. AIME, vol. 194, pp. 1047–52
35. Arzt E. (1982) Acta Metall., vol. 30, pp. 1883–9010.1016/0001-6160(82)90028-1 ↗
36. Scott G.D. (1962) Nature, vol. 194, pp. 956–5810.1038/194956a0 ↗
37. Mason G. (1968) Nature, vol. 217, pp. 733–3510.1038/217733a0 ↗
38. Choi K., Choi J.-W., Kim D.Y., Hwang N.M. (2000) Acta Mater., vol. 48, pp. 3125–2910.1016/S1359-6454(00)00117-8 ↗