Hot Ductility Characterization of Sanicro-28 Super-Austenitic Stainless Steel
Source abstract
Abstract
The hot ductility behavior of a super-austenitic stainless steel has been studied using tensile testing method in the temperature range from 1073 K to 1373 K (800 °C to 1100 °C) under the strain rates of 0.1, 0.01, and 0.001 s−1. The hot compression tests were also performed at the same deformation condition to identify the activated restoration mechanisms. At lower temperatures [i.e., 1073 K and 1173 K (800 °C and 900 °C)], the serration of initial grain boundaries confirms the occurrence of dynamic recovery as the predominant restoration process. However, in the course of applied deformation, the initial microstructure is recrystallized at higher temperatures [i.e., 1273 K and 1373 K (1000 °C and 1100 °C)]. In this respect, annealing the twin boundaries could well stimulate the recrystallization kinetic through initiation new annealing twins on prior annealing twin boundaries. The hot tensile results show that there is a general trend of increasing ductility by temperature. However, two regions of ductility drop are recognized at 1273 K and 1373 K (1000°C)/0.1s−1 and (1100°C)/0.01s−1. The ductility variations at different conditions of temperature and strain rate are discussed in terms of simultaneous activation of grain boundary sliding and restoration processes. The observed ductility troughs are attributed to the occurrence of grain boundary sliding and the resulting R-type and W-type cracks. The occurrence of dynamic recrystallization is also considered as the main factor increasing the ductility at higher temperatures. The enhanced ductility is primarily originated from the post-uniform elongation behavior, which is directly associated with the strain rate sensitivity of the experimental material.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. S.H. Wang, C.C. Wu, C.Y. Chen, J.R. Yang, P.K. Chiu, J. Fang: Metals Mater. Int., 2007, Vol. 13, pp. 275-283.10.1007/BF03027883 ↗
2. M. Moallemi, A. Zarei-Hanzaki, A. Mirzaei: J. Mater. Eng. Perform. 2015, Vol. 24, pp.2335-2340.10.1007/s11665-015-1501-6 ↗
3. M. Nezakat, H. Akhiani, M. Hoseini, J. Szpunar: Mater. Charact., 2014, Vol. 98, pp. 10–17.10.1016/j.matchar.2014.10.006 ↗
4. T. Koutsoukis, A. Redjaïmia, G. Fourlaris: Mater. Sci. Eng. A, 2013, Vol. 561, pp. 477-485.10.1016/j.msea.2012.10.066 ↗
5. A. Zambon, P. Ferro, F. Bonollo: Mater. Sci. Eng. A, 2006, Vol. 424, pp. 117-127.10.1016/j.msea.2006.03.003 ↗
6. X. Gomez, J. Echeberria: Mater. Sci. Eng. A, 2003, Vol. 348, pp. 180-191.10.1016/S0921-5093(02)00686-X ↗
7. S. Mandal, P.V.Sivaprasad, S.Venugopal, K.P.N. Murthy: Model. Simul. Mater. Sci., 2006, Vol. 14, pp. 1053-1070.
8. A. Mirzaei, A. Zarei-Hanzaki, M.H. Pishbin, Sh. Khoddam: J. Mater. Eng. Perform., 2015, Vol. 24, pp. 2412-2421.10.1007/s11665-015-1518-x ↗
9. Z.C. Sun, L.S. Zheng, H. Yang: Mater. Charact., 2014, Vol. 90, pp. 71–80.10.1016/j.matchar.2014.01.019 ↗
10. B. Mintz, S. Yue, J.J. Jonas: Int. Mater. Rev., 1991, Vol. 36, pp. 187-220.10.1179/imr.1991.36.1.187 ↗
11. H. Lue, L.P. Karjalainen, D.A. Porter, H.M. Liimatainen, Y. Zhang: ISIJ Int., 2002, Vol. 42, pp. 273-282.10.2355/isijinternational.42.273 ↗
12. F. Zarandi, S. Yue: ISIJ Int., 2006, Vol. 46, pp. 591-598.10.2355/isijinternational.46.591 ↗
13. A. Baradaran, A. Zarei-Hanzaki, H.R. Abedi, S.M. Fatemi-Varzaneh, A. Imandoust: Mater. Sci. Eng. A, 2013, Vol. 561, pp. 411-418.10.1016/j.msea.2012.10.051 ↗
14. L.H. Chown, L.A. Cornish: Mater. Sci. Eng. A, 2008, Vol. 494, pp. 263-275.10.1016/j.msea.2008.04.026 ↗
15. I. Mejía, A. Bedolla-Jacuinde, C. Maldonado, J.M. Cabrerab: Mater. Sci. Eng. A, 2011, Vol. 528, pp. 4133-4140.10.1016/j.msea.2011.01.102 ↗
16. E. López-Chipres, I. Mejía, C. Maldonado, A. Bedolla-Jacuinde, J.M Cabrera: Mater. Sci. Eng. A, Vol. 460–461, pp. 464–70.10.1016/j.msea.2007.01.098 ↗
17. G.W. Fan, J. Liu, P.D. Han, G.J. Qiao: Mater. Sci. Eng. A, 2009, Vol. 515, pp. 108-112.10.1016/j.msea.2009.02.022 ↗
18. F. Zarandi, S. Yue: Metal. Mater. Trans. A, 2004, Vol. 35, pp. 3823-3832.10.1007/s11661-004-0288-0 ↗
19. S. Akhlaghi, S. Yue: ISIJ Int., 2001, Vol. 41, pp. 1350-1356.10.2355/isijinternational.41.1350 ↗
20. L.B Mostefa, G. Saindrenan, M.P. Solignac, J.P. Colin: Acta Metall. Mater., 1991, Vol. 39, pp. 3111-3118.10.1016/0956-7151(91)90044-2 ↗
21. S.H. Song, Z.X. Yuan, J. Jia, D.D. Shen, A.M. Guo: Metal. Mater. Trans. A, 2003, Vol. 34, pp. 1611-1616.10.1007/s11661-003-0306-7 ↗
22. J. Calvo, A. Rezaeian, J.M. Cabrera, S. Yue: Eng. Fail. Anal., 2007, Vol. 14, pp. 374-383.10.1016/j.engfailanal.2006.02.013 ↗
23. B. Mintz, D.N. Crowther: Int. Mater. Rev., 2010, Vol. 55, pp. 168-196.10.1179/095066009X12572530170624 ↗
24. B. Mintz, R. Abushosha: Ironmak Steelmak., 1993, Vol. 20, pp. 445-452.
25. F. Zarandi, S. Yue: ISIJ Int., 2004, Vol. 44, pp. 1705-1713.10.2355/isijinternational.44.1705 ↗
26. Z. Mohamed: Mater. Sci. Eng. A, 2002, Vol. 326, pp. 255-260.10.1016/S0921-5093(01)01490-3 ↗
27. P.J. Szabo: Mater. Charact., 2012, Vol. 66, pp. 99–103.10.1016/j.matchar.2011.09.003 ↗
28. S.H. Song, A.M. Guo, D.D. Shen, Z.X. Yuan, J. Liu, T.D. Xu: Mater. Sci. Eng. A, 2003, Vol. 360, pp. 96-100.10.1016/S0921-5093(03)00438-6 ↗
29. W. Ozgowicz: J. Mater. Process. Technol., 2005, Vol. 162-163, pp. 392-401.10.1016/j.jmatprotec.2005.02.008 ↗
30. S.C. Seo, K.S. Son, S.K. Lee, I. Kim, T.J. Lee, C. Yim, D. Kim: Metal. Mater. Int., 2008, Vol. 14, pp. 559-563.10.3365/met.mat.2008.10.559 ↗
31. ASTM E21: Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials, Annual Book of ASTM Standards, USA, 1988.
32. ASTM E209: Standard Practice for Compression Tests of Metallic Materials at Elevated Temperatures With Conventional or Rapid Heating Rates and Strain Rates, Annual Book of ASTM Standards, ASTM International, PA, 2010.
33. R. Ebrahimi, A. Najafizadeh: J. Mater. Process. Technol., 2004, Vol. 152, pp. 136–143.10.1016/j.jmatprotec.2004.03.029 ↗
34. H. Miura, T. Sakai, H. Hamaji, J.J. Jonas: Scr. Mater., 2004, Vol. 50, pp. 65–69.10.1016/j.scriptamat.2003.09.035 ↗
35. A.S. Taylor, P.D. Hodgson: Mater. Sci. Eng. A, 2011, Vol. 528, pp. 3310-3320.10.1016/j.msea.2010.12.093 ↗
36. A. Mirzaei, A. Zarei-Hanzaki, N. Haghdadi, A. Marandi: Mater. Sci. Eng. A, 2014, Vol. 589, pp. 76-82.10.1016/j.msea.2013.09.036 ↗
37. L. Sun, K. Muszka, B.P. Wynne, E.J. Palmiere: Mater. Sci. Eng. A, 2013, Vol. 568, pp. 160–170.10.1016/j.msea.2013.01.045 ↗
38. E.I. Poliak, J.J. Jonas: Acta Metall., 1996, Vol. 44, pp. 127-136.
39. L. Sun, K. Muszka, B.P. Wynne, E.J. Palmiere: Acta Metall., 2014, Vol. 66, pp. 132–149.
40. D.P. Field, L.T. Bradford, M.M. Nowell, T.M. Lillo: Acta Mater., 2007, Vol. 55, pp. 4233-4241.10.1016/j.actamat.2007.03.021 ↗
41. J.W. Hutchinson, K.W. Neale: Acta Metall., 1977, Vol. 25, pp. 839-846.10.1016/0001-6160(77)90168-7 ↗
42. H.R. Abedi, A. Zarei-Hanzaki, S.M. Fatemi-Varzaneh, A.A. Roostaei: Mater. Des., 2010, Vol. 31, pp. 4386-4391.10.1016/j.matdes.2010.05.004 ↗
43. M. Taheri-Mandarjani, A. Zarei-Hanzaki, H.R. Abedi: Mater. Sci. Eng. A, 2015, Vol. 637, pp. 107-122.10.1016/j.msea.2015.03.038 ↗
44. M. Urdanpilleta, J.M. Martínez-Esnaola, J. Gil Sevillano: Mater. Trans., 2005, vol. 46, pp. 1711–19.10.2320/matertrans.46.1711 ↗
45. K. Wu, G. Liu, B. Hu, F. Li, Y. Zhang, Y. Tao, J. Liu: Mater. Charact., 2010, Vol. 16, pp. 330–340.10.1016/j.matchar.2009.12.013 ↗
46. Y.H. Wei, Q.D. Wang, Y.P. Zhu, H.T. Zhou, W.J. Ding, Y. Chino, M. Mabuchi: Mater. Sci. Eng. A, 2003, Vol. 360, pp. 107-115.10.1016/S0921-5093(03)00407-6 ↗
47. A.H. Chokshit, A.K. Mukherjee: Acta Metall., 1989, Vol. 37, pp. 3007-3017.10.1016/0001-6160(89)90337-4 ↗
48. T. Kizu, T. Urabe: ISIJ Int., 2009, Vol. 49, pp. 1424-1431.10.2355/isijinternational.49.1424 ↗
49. J. Calvo, J.M. Cabrea, A. Rezaeian, S. YUE: ISIJ Int., 2007, Vol. 47, pp. 1518-1526.10.2355/isijinternational.47.1518 ↗
50. A. Heinz, P. Neumann: Acta metallurgica et materialia, 1990, Vol. 38, pp. 1933-1940.10.1016/0956-7151(90)90305-Z ↗
51. M.J. Stowell: Met. Sci,. 1980, Vol. 14, pp. 267-272.10.1179/030634580790426373 ↗
52. A. Hoseini Asli, A. Zarei-Hanzaki: J. Mater. Sci. Technol., 2009, vol. 25, pp. 603–06.