journal article·2010-12

The Effects of Al2O3 Amount on the Microstructure and Properties of Fe-Cr Matrix Composites

Saidatulakmar Shamsuddin, Shamsul Baharin Jamaludin, Zuhailawati Hussain, Zainal Arifin Ahmad

Publisher page

Abstract

Iron based matrix composites reinforced with 5 to 25 wt pct of Al2O3 particles were fabricated using the powder metallurgy method. The samples were prepared by mixing at 250 rpm for 30 minutes, uniaxially pressing at 750 MPa and sintering in a vacuum furnace at a temperature of 1373 K (1100 °C) for 2 hours with 10 °C/min heating rate. The optimum amount of reinforcement was determined by evaluating the microstructure, relative density, total porosity, micro Vickers hardness, and wear resistance of the composites. The results and analysis revealed that the micro Vickers hardness and wear resistance of the composites were better after increasing the reinforcement up to 20 wt pct. Increasing the Al2O3 particles to 25 wt pct resulted in a decrease in mechanical properties due to agglomeration of the particles in the matrix, which lowers the interaction between the matrix and reinforcement.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Powder Metallurgy Techniques and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. K.S. Al-Rubaie: Wear, 2000, vol. 243, pp. 92–100.10.1016/S0043-1648(00)00425-7 ↗
2. R.M. German: Powder Metallurgy Science, 2nd ed., Metal Powder Industries Federation, Princeton, NJ, 1994.
3. I.A. Ibrahim, F.A. Mohamed, and E.J. Lavernia: Mater. Sci., 1991, vol. 26, pp. 1137–56.10.1007/BF00544448 ↗
4. G.S. Upadhyaya: Sintered Metallic and Ceramic Materials Preparation, Properties and Application, John Wiley & Sons Ltd., West Sussex, England 2000.
5. T. Miyajima and Y. Iwai: Wear, 2003, vol. 255, pp. 606–16.10.1016/S0043-1648(03)00066-8 ↗
6. S.K. Mukherjee and S. Bandyopadhyay: Mater. Sci. Eng., 1995, vol. A202, pp. 123–27.10.1016/0921-5093(95)09810-0 ↗
7. R. Subramaniam, C.G. McKamey, L.R. Buck, and J.H. Schneibel: Mater. Sci. Eng., 1997, vols. A239–A240, pp. 640–46.10.1016/S0921-5093(97)00642-4 ↗
8. N. Travitzky, P. Kumar, K.H. Sandhage, R. Janssen, and N. Claussen: Mater. Sci. Eng. A, 2003, vol. 344 (1–2), pp. 245–52.10.1016/S0921-5093(02)00419-7 ↗
9. V.G. Karayannis and A.K. Moutsatsou: J. Mater. Process. Technol., 2006, vol. 171 (2), pp. 295–300.10.1016/j.jmatprotec.2005.07.006 ↗
10. J.Q. Li, W.A. Sun, W.Q. Ao, K.M. Gu, and P. Xiao: Appl. Sci. Manufact., 2007, vol. 38 (2), pp. 615–20.10.1016/j.compositesa.2006.02.012 ↗
11. S.K. Mukherjee and G.S. Upadhyaya: Mater. Sci. Eng., 1985, vol. 75, pp. 67–78.10.1016/0025-5416(85)90178-8 ↗
12. A. Upadhyaya and G.S. Upadhyaya: Mater. Design, 1995, vol. 16 (1), pp. 41–45.10.1016/0261-3069(95)00006-K ↗
13. M. Boz and A. Kurt: Tribology Int., 2007, vol. 40, pp. 1161–69.10.1016/j.triboint.2006.12.004 ↗
14. M. Rahimian, N. Ehsani, N. Parvin, and H.R. Baharvandi: Mater. Design, 2009, vol. 30, pp. 3333–37.10.1016/j.matdes.2008.11.027 ↗
15. Y. Lu: Compos. Sci. Technol., 2006, vol. 66 (3–4), pp. 591–98.10.1016/j.compscitech.2005.05.032 ↗
16. S.L. Draper and B.J.M. Aikin: Mater. Sci. Eng. A, 1999, vol. 266, pp. 18–29.10.1016/S0921-5093(99)00033-7 ↗
17. E. Pagounis and V.K. Lindroos: Mater. Sci. Eng. A, 1998, vol. 246 (1–2), pp. 221–34.10.1016/S0921-5093(97)00710-7 ↗
18. M. Vardavoulias, M. Jeandin, F. Velasco, and J.M. Torralba: Tribology Int., 1996, vol. 29 (6), pp. 499–506.10.1016/0301-679X(95)00110-P ↗
19. E.M. Uygur: Int. J. Mach. Tools Manufact., 1997, vol. 37 (10), pp. 1539–53.10.1016/0890-6955(95)00093-3 ↗
20. S.D. Peteves, M. Paulasto, G. Ceccone, and V. Stamos: Acta Mater., 1998, vol. 46 (7), pp. 2407–14.10.1016/S1359-6454(97)00398-4 ↗
21. J.X. Zhang, R.S. Chandel, and H.P. Seow: Mater. Chem. Phys., 2002, vol. 75, pp. 256–59.10.1016/S0254-0584(02)00072-X ↗
22. M.G. Fontana: Corrosion Engineering, McGraw–Hill, New York, NY, 1987, pp. 282–87.
23. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: Proc. Nat. Metallurgical Conf. 2007, Johor Bahru, Johor, Malaysia, Nov. 26–27, 2007.
24. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: Proc. 23rd Regional Conf. on Solid State Science and Technology 2007, Johor Bahru, Johor, Malaysia, Nov. 27–29, 2007.
25. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: Malaysian J. Microsc., 2007, vol. 4, pp. 118–23.
26. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: Proc. Int. Conf. on X-rays & Related Techniques in Research & Industry, Langkawi, Malaysia, June 9–10, 2010.
27. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: American Institute of Physics Conf. Proc. 1217, American Institute of Physics, Melville, NY, 2010, pp. 419–23.
28. A. Slipenyuk, V. Kuprin, Y. Milman, V. Goncharuk, and J. Eckert: Acta Mater., 2006, vol. 54 (1), pp. 157–66.10.1016/j.actamat.2005.08.036 ↗
29. S. Shamsuddin, J. Shamsul Baharin, Z. Hussain, and Z.A. Ahmad: J. Phys. Sci., 2008, vol. 19 (1), 89–95.
30. E.P. Rajiv, A. Iyer, and S.K. Seshadri: Wear, 1995, vol. 189 (1–2), pp. 100–06.10.1016/0043-1648(95)06670-5 ↗
31. S.K. Mukherjee and S. Bandyopadhyay: Compos. Part B: Eng., 1997, vol. 28 (1–2), pp. 45–48.10.1016/S1359-8368(96)00036-4 ↗
32. R.K. Gurudu, R.O. Scattergood, C.C. Koch, K.L. Murty, S. Guruswamy, and M.K. McCarter: Scripta Mater., 2006, vol. 54 (11), pp. 1879–83.10.1016/j.scriptamat.2006.02.014 ↗
33. D. Hull and T.W. Clyne: An Introduction to Composite Materials, 2nd ed., Cambridge University Press, Cambridge, United Kingdom, 1996, pp. 133–52.10.1017/CBO9781139170130.009 ↗
34. I.M. Hutchings: Mater. Sci. Technol., 1994, pp. 513–17.10.1179/mst.1994.10.6.513 ↗
35. F. Velasco and E. Gordo: Int. J. Refractory Met. Hard Mater., 2001, vol. 19 (4–6), pp. 319–23.10.1016/S0263-4368(01)00053-1 ↗
36. F. Velasco and R. Isabel: Compos. Part A: Appl. Sci. Manufact., 2002, vol. 33 (6), pp. 819–27.10.1016/S1359-835X(02)00024-6 ↗
37. J.F. Abenojar, F. Velasco, and M.A. Martinez: J. Mater. Process. Technol., 2007, vol. 184 (1–3), pp. 441–46.10.1016/j.jmatprotec.2006.11.122 ↗
38. S.K. Thakur and B.K. Dhindaw: Wear, 2001, vol. 247 (2), pp. 191–201.10.1016/S0043-1648(00)00536-6 ↗