journal article·2015-11

Calorimetric Study of Phase Stability and Phase Transformation in U-xZr (x = 2, 5, 10 wt pct) Alloys

Arun Kumar Rai, Raju Subramanian, Raj Narayan Hajra, Haraprasanna Tripathy, Mythili Rengachari, Saroja Saibaba

Publisher page

Abstract

A comprehensive calorimetric study of high-temperature phase equilibria and phase transformation characteristics in U-xZr (x = 2, 5, 10 wt pct) alloys has been undertaken, as a function of heating and cooling rates. It is found that the following sequence of phase transformation takes place upon slow heating in annealed U-2 wt pct Zr alloy: α + α′ + δ-UZr2 → α + γ 2 → β + γ 2 → β + γ 1 → γ. For alloys of 5 and 10 wt pct Zr, the additional presence of a miscibility gap (γ 1 U-rich bcc + γ 2 Zr-rich bcc) in the high-temperature γ(bcc) phase region resulted in the following transformation sequence: α + α′ + δ-UZr2 → α + γ 2 → β + γ 2 → γ 1 + γ 2 → γ. Further, it has been demonstrated that depending on the nature of starting microstructure, namely whether it is α eq + δ-UZr2, or a mix of α′ + α eq + δ-UZr2 phases, the relative extents of two possible co-occurring modes of the first on-heating phase transformation step differ. In case of starting microstructure having mixture of three phases α′ + α eq + δ-UZr2, it is found that α′-martensite relaxation via α′ + α eq + δ-UZr2 → α eq + δ-UZr2 constitutes the first on-heating thermal response. The α′-martensitic relaxation is very closely followed by the dissolution of δ-UZr2. The co-occurrence of these two events gives rise to a composite thermal arrest in a normal dynamic calorimetry profile. However, if the starting microstructure is the one having the equilibrium mix of α eq and δ-UZr2, then only the peritectoidal dissolution of δ-UZr2 is found in the calorimetry profile. Unless, a very slow cooling rate of the order of 0.1 K min−1 is adopted from high-temperature γ(bcc) phase, it is not possible to obtain 100 pct of α eq phase along with equilibrium amount of δ-UZr2. At normal and high cooling rates, it is possible to suppress the diffusional decomposition of γ to varying extents. The direct γ → α′-martensite transformation has been observed at sufficiently higher cooling rates. It has been also noticed that even after γ → α′-martensite transformation the precipitation of δ-UZr2 phase is possible at lower temperature during non-isothermal cooling. Further, the critical cooling rate required for γ → α′ displacive transformation is found to decrease with increasing Zr content. For U-2, 5, and 10 wt pct Zr alloys, it is found to be of the order of, 60, 20, 10 K min−1, respectively. The cooling rate from high-temperature γ(bcc) is found have a strong influence on microstructure evolution as well. The kinetic aspects of α → β diffusional transformation that occurs on heating have been modeled in terms of Kolmogorov–Johnson–Mehl–Avrami formalism, and it is found that the transformation is effectively controlled by the diffusion of Zr in α′-orthorhombic phase. Continuous heating and cooling transformation diagrams have also been obtained for U-2 wt pct Zr alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Nuclear Materials and Properties · Fusion materials and technologies · Nuclear reactor physics and engineering

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. P. E. Potter, J. Nucl. Mater., 2009, vol. 389, pp. 29-44.10.1016/j.jnucmat.2009.01.004 ↗
2. D. E. Burkes, R. S. Fielding, D. L. Porter, D. C. Crawford and M. K. Meyer, J. Nucl. Mater., 2009, vol. 389, pp. 458-469.10.1016/j.jnucmat.2009.02.035 ↗
3. W. J. Carmack, D. L. Porter, Y. I. Chang, S. L. Hayes, M. K. Meyer, D. E. Burkes, C. B. Lee, T. Mizuno, F. Delage and J. Somers, J. Nucl. Mater., 2009, vol. 392, pp. 139-150.10.1016/j.jnucmat.2009.03.007 ↗
4. D. E. Burkes, R. S. Fielding and D. L. Porter, J. Nucl. Mater., 2009, vol. 392, pp. 158-163.10.1016/j.jnucmat.2009.03.009 ↗
5. C. R. F. Azevedo, Eng. Failure Analysis, 2011, vol. 18, pp. 1943-1962.10.1016/j.engfailanal.2011.06.010 ↗
6. A. Riyas, P. Mohanakrishnan, Ann. Nucl. Energ., 2008, vol. 35, pp. 87-92.10.1016/j.anucene.2007.05.015 ↗
7. G. L. Hofman, L. C. Walters and T. H. Bauer, Progr. Nucl. Energy, 1997, vol. 31 pp. 83-110.10.1016/0149-1970(96)00005-4 ↗
8. R.A. Vandermeer: Proceedings of the Third Army Materials Technology Conference, Vail, CO, February 1974, p. 259.
9. H.H. Chiswik, A.E. Dwight, L.T. Lloyd, M.V. Nevitt, and S.T. Zegler: Proceedings of the Second United Nations International Conference on Peaceful Uses of Atomic Energy, June 1985, p. 1.
10. D. Blake and R.F. Hehemann: Proceedings of the Third Army Materials Technology Conference, Vail, CO, February 1974, p. 189.
11. J. Burke and P.H. Dixon: Symposium on Uranium & Graphite, London Institute of Metals, London, 1962.
12. A.N. Holden: Physical Metallurgy of Uranium, Addison-Wesley Publishing Co Inc, Reading, 1958.
13. J. J. Burke, Physical Metallurgy of Uranium Alloys, Hill Publishing Co. Inc, USA, 1974.
14. O. S. Ivanov, Phase Diagram of Uranium Alloys, Nauka Publishers, Moscow, 1972.
15. H. Okamoto, J. Phase Equilibria, 2007, vol. 28, pp. 499-500.10.1007/s11669-007-9155-1 ↗
16. D. Summers-Smith: J. Inst. Met. 1954–1955, vol. 83, pp. 277–82.
17. J. F. Duffey, and C. A. Bruch, Trans. AIME, 1958, vol. 212, pp 17-19.
18. F.A. Rough and A.A. Bauer: Battelle (USA) Report BMI-1300, 1958.
19. A.A. Bauer: Battelle (USA) Report BMI-1350, 1959.
20. S.T. Zegler: USAEC Rep. ANL-6055, 1962.
21. R. R. Sheldon and D. E. Peterson, Bulletin of Alloy Phase Diagram, 1989, vol. 10, pp. 165-171.10.1007/BF02881432 ↗
22. H. Baker, ASM Handbook: Alloy Phase Diagrams, ASM International, Materials Park, 1992.
23. M. Kurata, T. Ogata, K. Nakamura and T. Ogawa, J. Alloys Compd., 1998, vol. 271–273, pp. 636-640.10.1016/S0925-8388(98)00176-5 ↗
24. P. Y. Chevalier, E. Fischer, J. Nucl. Mater. 1998, vol. 257 pp. 213–255.10.1016/S0022-3115(98)00450-4 ↗
25. P. Y. Chevalier, E. Fischer and B. Cheynet, CALPHAD: Coupl. Phase Diag. Thermochem. 2004, vol. 28, pp. 15–40.10.1016/j.calphad.2004.03.005 ↗
26. C. B. Basak, G. J. Prasad, H. S. Kamath and N. Prabhu, J. Alloys Comp., 2009, vol. 480, pp. 857-862.10.1016/j.jallcom.2009.02.077 ↗
27. W. Xiong, W. Xie, C. Shen and D. Morgan, J. Nucl. Mater., 2013, vol. 443, pp. 331-341.10.1016/j.jnucmat.2013.07.034 ↗
28. A. KumarRai, S. Raju, H. Tripathy, R.N. Hajra, and M. Vijayalakshmi: Trans. Ind. Inst. Met., 2013, vol. 66, pp. 387–90.10.1007/s12666-013-0247-9 ↗
29. B.W. Howlett and A.G. Knapton: Paper P/1469, Proc. 2 nd U. N. International Conference on Peaceful use at Geneva, 1958, vol. 6, pp. 104–10.
30. G. Lagerberg, J. Nucl. Mater., 1962, vol. 9, pp. 261-276.10.1016/0022-3115(63)90144-2 ↗
31. M. Akabori, A. Itoh, T. Ogawa, F. Kobayashi and Y. Suzuki, J. Nucl. Mater 1992, vol. 188, pp. 249-254.10.1016/0022-3115(92)90480-9 ↗
32. M. Akabori, T. Ogawa, A. Itoh, and Y. Morii: J. Phys. Condens. Matter., 1995, vol. 7, pp. 8249–57.10.1088/0953-8984/7/43/005 ↗
33. C. B. Basak, R. Keswani, G. J. Prasad, H. S. Kamath and N. Prabhu, J. Alloys Compd., 2009 vol. 471, pp. 544-552.10.1016/j.jallcom.2008.04.021 ↗
34. S. Kaity, J. Banerjee, M. R. Nair, K. Ravi, S. Das, T. R. G. Kutty, Arun Kumar and R. P. Singh, J. Nucl. Mater., 2012, vol. 427, pp. 1-11.10.1016/j.jnucmat.2012.03.045 ↗
35. T. Mckeown, S. Irukuvarghula, S. Ahn, M. A. Wall, L. L. Hsiung, S. McDeavitt and P. E. A. Turuchi, J. Nucl. Mater., 2013, vol. 436, pp. 100-104.10.1016/j.jnucmat.2013.01.313 ↗
36. S. Ahn, S. Irukuvarghula and S. M MeDeavitt, J. Alloys Compd., 2014 vol. 611, pp. 355-362.10.1016/j.jallcom.2014.05.126 ↗
37. R. F. Hills, B. R. Butcher, B. W. Howlett and D. Stewart, J. Nucl. Mater., 1965, vol. 16, pp. 25–38.10.1016/0022-3115(65)90088-7 ↗
38. C. Basak, J. Nucl. Mater., 2011, vol. 416, pp. 280-287.10.1016/j.jnucmat.2011.06.011 ↗
39. C. Basak, R. Keswani, G. J. Prasad, H. S. Kamath N. Prabhu and S. Banerjee, J. Nucl. Mater., 2009, vol. 393, pp. 146-152.10.1016/j.jnucmat.2009.05.018 ↗
40. C. B. Basak, N. Prabhu and M. Krishnan, Intermetallics, 2010, vol. 18, pp. 1707-1712.10.1016/j.intermet.2010.05.006 ↗
41. C. B. Basak, S. Neogy, D. Srivastava, G. K. Dey and S. Banerjee, Philos. Mag., 2011, vol. 91, pp. 3290-3306.10.1080/14786435.2011.577756 ↗
42. J. Lehmann, and R. Hills, J. Nucl. Mater., 1960, vol. 2, pp. 261-268.10.1016/0022-3115(60)90060-X ↗
43. H.L. Yakel: The Physical Metallurgy of Uranium alloys Conference sponsored by the AEC Army Material and Mechanical Research Centre, Vail Colorado, February 1974.
44. H. L. Yakel, J. Nucl. Mater., 1969, vol. 33, pp. 286-295.10.1016/0022-3115(69)90022-1 ↗
45. R. A. Vandermeer, Acta Metall., 1979, vol. 28, pp. 383-393.10.1016/0001-6160(80)90173-X ↗
46. J. G. Speer and D. V. Edmonds, Acta Metall., 1988, vol. 36, pp. 1015-1033.10.1016/0001-6160(88)90156-3 ↗
47. A. KumarRai, S. Raju, B. Jeyaganesh, E. Mohandas, R. Sudha, and V. Ganesan, J. Nucl. Mater., 2009, vol. 383, pp. 215–225.10.1016/j.jnucmat.2008.09.012 ↗
48. P. Kruger, J Phys. Chem. Solids, 1993, vol. 54, pp. 1549-1555.10.1016/0022-3697(93)90349-V ↗
49. E. J. Mittemeijer, J. Mat. Sci., 1992, vol. 27, pp. 3977-3987.10.1007/BF01105093 ↗
50. G. Ruitenberg, E. Woldt and A. K. Petford-Long, Thermochim. Acta, 2001, vol. 378, pp. 97-105.10.1016/S0040-6031(01)00584-6 ↗
51. Y. C. Liu, F. Sommer and E. J. Mittemeijer, Acta Mater, 2006, vol. 54, pp. 3383-3393.10.1016/j.actamat.2006.03.029 ↗
52. R. Massih and L. O. Jernkvist, Modell. Simul. Mater. Sci. Eng., 2009, vol. 17, pp. 055002-15.10.1088/0965-0393/17/5/055002 ↗
53. S. Malinov, Z. Guo, W. Sha, and A. Wilson, Metall. Trans A. 2001, vol. 32, pp. 8798-87.
54. Y. Adda and A. Kirianenko, J. Nucl. Mater., 1962, vol. 6 pp. 135-136.10.1016/0022-3115(62)90225-8 ↗
55. A. Landa, P. Söderlind and P. E. A. Turchi, J. Nucl. Mater., 2011, vol. 414, pp. 132–137.10.1016/j.jnucmat.2011.02.019 ↗
56. T. Ogata, M. Aakabori, A. Itoh and T. Ogawa, J. Nucl. Mater., 1996, vol. 232, pp. 125-130.10.1016/S0022-3115(96)00409-6 ↗
57. M. Akabori, A. Itoh, T. Ogawa and T. Ogata, J. Alloys Comp., 1998, vol. 271-273, pp. 597-601.10.1016/S0925-8388(98)00167-4 ↗
58. W. Li, R. Hu, Y. W. Cui, H. Zhong, H. Chang, J. Li and L. Zhou, J. Nucl. Mater., 2010, vol. 407, pp. 220-227.10.1016/j.jnucmat.2010.10.035 ↗
59. W. J. Kitchingman, K. M. Pickwick, I. G. Brown and R. J. Edwards, J. Nucl. Mater., 1966, vol.18, pp. 219-225.10.1016/0022-3115(66)90085-7 ↗
60. R. D. Townsend and J. Burke, J. Nucl. Mater., 1965, vol. 17, pp. 215-226.10.1016/0022-3115(65)90165-0 ↗