Semi-solid rapid compression testing of spray-formed hypereutectic Al-Si alloys
Source abstract
Abstract
The rheology of Al-30Si-5Cu and Al-30Si-5Cu-2Mg spray-formed alloys has been characterized after holding at various times and temperatures, using semisolid rapid compression to obtain load-displacement curves. Microstructures were examined after partial remelting and compression in an attempt to understand the flow behavior. The initial resistance to flow generally increased with holding time at temperature. This increase was attributed to the increased strength of a three-dimensional (3-D) solid silicon network present in these alloys in the semisolid state, with the initial resistance to flow smaller in the magnesium-containing alloys. With increased temperature, the initial resistance decreased due to increased liquid content and grain spheroidization. The viscosity vs shear rate response was studied using the approach of Laxmanan and Flemings. The materials shear thinned rapidly during the test conditions, in which the shear rate rapidly increased from approximately 2.5 to 92 s−1. The results were fitted to a power-law model, and the viscosities showed a drop of approximately two to four orders of magnitude when extrapolated to a shear rate of 1000 s−1 (a typical value in actual component manufacture). The rapid compression test, which is close to conditions present in component manufacture, was shown to have more in common with a shear rate jump experiment, rather than steady-state viscometry.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. N. Tenekedjiev and J.E. Gruzleski: Cast Met., 1990, vol. 3, pp. 96–105.10.1080/09534962.1990.11819026 ↗
2. P.S. Grant: Progr. Mater. Sci., 1995, vol. 39, pp. 497–545.10.1016/0079-6425(95)00004-6 ↗
3. M.C. Flemings: Metall. Trans. A., 1991, vol. 22A, pp. 269–92.10.1007/BF02651227 ↗
4. P.J. Ward, H.V. Atkinson, D.H. Kirkwood, and C.M. Sellars: Proc. 2nd Int. Conf. on Semi-Solid Processing of Alloys and Composites, Cambridge, MA, 1992, S.B. Brown and M.C. Flemings, eds., Massachusetts Institute of Technology Press, Cambridge, MA, 1992, pp. 440–46.
5. P. Kapranos, D.H. Kirkwood, and M.R. Barkhudarov: Proc. 5th Int. Conf. on Semisolid Processing of Alloys and Composites, Golden, CO, 1998, A.K. Bhasin, J.J. Moore, K.P. Young, and S. Midson, eds., Colorado School of Mines, Golden, CO, 1998, pp. 11–19.
6. T.Y. Liu, H.V. Atkinson, P. Kapranos, D.H. Kirkwood, and S.C. Hogg: Metall. Mater. Trans. A, in press.
7. W.R. Loué, M. Suery, and J.L. Querbes: Proc. 2nd Int. Conf. on Semi-Solid Processing of Alloys and Composites, Cambridge, MA, 1992, S.B. Brown and M.C. Flemings, eds., Massachusetts Institute of Technology Press, Cambridge, MA, 1992, pp. 266–75.
8. L. Salvo, M. Suéry, Y. De Charentenay, and W. Loué: Proc. 4th Int. Conf. on Semisolid Processing of Alloys and Composites, Sheffield, United Kingdom, 1996, D.H. Kirkwood and P. Kapranos, eds., University of Sheffield, Sheffield, United Kingdom, 1996, pp. 10–15.
9. D.S. Han, I. Stone, and B. Cantor: Proc. AFDM’99, Haeundae, Korea, 1999, C.G. Kang and Y.H. Moon, eds., Pusan National University, Pusan, Korea, 1999, pp. 65–70.
10. E. Tzimas, A. Zavaliangos, A. Lawley, and C. Pumberger: Proc. 4th Int. Conf. on Semisolid Processing of Alloys and Composites, Sheffield, United Kingdom, 1996, D.H. Kirkwood and P. Kapranos, eds., University of Sheffield, Sheffield, United Kingdom, 1996, pp. 40–46.
11. A. Meetsma, J.L. de-Boer, and S. van-Smaalen: J. Solid State Chem., 1989, vol. 83, pp. 370–72.10.1016/0022-4596(89)90188-6 ↗
12. Smithell’s Metals Reference Book, 7th ed., E.A. Brandes and G.B. Brook, eds., Butterworth-Heinemann, Oxford, England, 1992.
13. E. Tzimas and A. Zavaliangos: J. Mater. Sci., 2000, vol. 35, pp. 5319–329.10.1023/A:1004890711322 ↗
14. F. Mondolfo: Aluminium Alloys, Structures and Properties, Butterworth and Co., London, 1976.
15. E. Tzimas and A. Zavaliangos: Acta Mater., 1999, vol. 47, pp. 517–28.10.1016/S1359-6454(98)00356-5 ↗
16. D.H. Warrington and M. Boon: Acta Metall., 1975, vol 23, pp. 599–607.10.1016/0001-6160(75)90100-5 ↗
17. C.S. Smith: Trans. Am. Inst. Min. Met. Eng., 1948, vol. 175, pp. 15–51.
18. V. de L. Davies and J.M. West: J. Inst. Met., 1963–64, vol. 92, pp. 175–80.
19. M. Gündüz and J.D. Hunt: Acta Metall., 1985, vol. 33, pp. 1651–672.10.1016/0001-6160(85)90161-0 ↗
20. A. Otsuki: Acta Mater., 2001, vol. 49, pp. 1737–45.10.1016/S1359-6454(01)00090-8 ↗
21. D.P. Woodruff: The Solid-Liquid Interface, Cambridge University Press, Cambridge, United Kingdom, 1973.
22. K.A. Jackson: Liquid Metals and Solidification, ASM, Cleveland, OH, 1958.
23. H.A. Steen and A. Hellawell: Acta Metall., 1975, vol. 23, pp. 529–35.10.1016/0001-6160(75)90093-0 ↗
24. S. Annavarapu and R.D. Doherty: Acta Metall. Mater., 1995, vol. 43, pp. 3207–230.10.1016/0956-7151(94)00448-Q ↗
25. P. Kapranos, T.Y. Liu, H.V. Atkinson, and D.H. Kirkwood: J. Mater. Process. Technol., 2001, vol. 111, pp. 31–36.10.1016/S0924-0136(01)00534-9 ↗
26. E.D. Hondros and D. McLean: in Grain Boundary Structure and Properties, G.A. Chadwick and D.A. Smith, eds., Academic Press Inc., London, 1976.
27. A. Gupta, A. Jena, and M. Chaturvedi: Mater. Sci. Technol., 1987, vol. 3, pp. 1012–18.10.1179/mst.1987.3.12.1012 ↗
28. S.C. Hogg: Ph.D. Thesis, University of Sheffield, Sheffield, United Kingdom, England, 2001.
29. V. Laxmanan and M.C. Flemings: Metall. Trans. A, 1980, vol. 11A, pp. 1927–36.10.1007/BF02655112 ↗
30. G.J. Diemes and H.F. Klemm: J. Appl. Phys., 1946, vol. 17, pp. 458–71.10.1063/1.1707739 ↗
31. C.J. Quaak: Ph.D. Thesis, Technische Universiteit Delft, Delft, The Netherlands, 1996.
32. T.Y. Liu, P.J. Ward, D.H. Kirkwood, and H.V. Atkinson: XIIIth Int. Congr. on Rheology, Cambridge, D.M. Binding, N.E. Hudson, J. Mewis, J.-M. Piau, C.J.S. Petrie, P. Townsend, M.H. Wagner, and K. Watters, eds., British Society of Rheology, Glasgow, United Kingdom, 2000, vol. 4, pp. 61–63.
33. T.Y. Liu, H.V. Atkinson, P.J. Ward, and D.H. Kirkwood: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 409–17.10.1007/s11661-003-0342-3 ↗
34. D.H. Kirkwood: Int. Mater. Rev., 1994, vol. 39, pp. 173–89.10.1179/imr.1994.39.5.173 ↗
35. W.R. Loue, M. Suery, and J.L. Querbes: Proc. 2nd Int. Conf. on Semisolid Processing of Alloys and Composites, Cambridge, MA, 1992, S.B. Brown and M.C. Flemings, eds., Massachusetts Institute of Technology Press, Cambridge, MA, 1992, pp. 266–75.
36. I. Diewwanit and M.C. Flemings: Proc. 4th Int. Conf. on Semisolid Processing of Alloys and Composites, Sheffield, United Kingdom, 1996, D.H. Kirkwood and P. Kapranos, eds., University of Sheffield, Sheffield, United Kingdom, 1996, pp. 30–34.