journal article·2006-01

Effect of annealing time on solute carbon in ultralow-carbon Ti-V and Ti-Nb steels

Waleed Al-Shalfan, John G. Speer, David K. Matlock, Kip Findley

Publisher page

Abstract

The influence of annealing temperature and time on solute carbon levels was investigated in four ultralow-carbon (ULC) bake-hardenable steels; two Ti-V ULC steels with different V/C levels and two Ti-Nb ULC steels with different Nb/C levels. Internal-friction and scanning transmission electron microscopy (STEM) techniques were used to understand the precipitation/dissolution behavior in the various steels. An effect of annealing time on the carbon Snoek-peak height was observed in both Ti-V steels and in the Ti-Nb steel having a lower Nb/C ratio. Despite differences between these steels resulting from their composition (and, thus, carbide solubility) differences, after cold rolling and annealing at different temperatures, the maximum Snoek-peak height was achieved after annealing for shorter times in each instance, on the order of 1 minute. The highly stabilized Ti-Nb ULC steel with a higher Nb/C ratio did not show the effect because of the absence of solute carbon. For the Ti-V steels, most of the precipitates examined using STEM contained both Ti and V. The energy-dispersive X-ray (EDX) analysis indicated that both the Ti-V steels annealed at 845 °C for 1 minute have greater Ti/V ratios compared to their corresponding Ti-V steels in the as-received (hot-rolled) condition. This behavior is consistent with dissolution of carbides causing the carbon in solution to increase, as indicated by a greater carbon Snoek-peak height for both Ti-V steels in the annealed condition. The reduction in Snoek-peak height at longer annealing times is believed to be associated with segregation to lower-energy defect sites.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal and Thin Film Mechanics · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. T. Irie, S. Satoh, A. Yasuda, and O. Hashimoto: in Metallurgy of Annealed Sheet Steel, B. Bramfitt and P. Mangonon, eds., TMS-AIME, Warrendale, PA, 1982, pp. 155–71.
2. K.A. Taylor and J.G. Speer: Development of Vanadium-Alloyed Bake Hardenable Sheet Steels for Hot Dip Coated Applications, Proc. 39th Mechanical Working and Steel Processing Conf., Indianapolis, IN, USA, Oct. 1997, ISS-AIME, Warrendale, PA, 1998, pp. 49–61.
3. T.E. Gladman and P.S. Mitchell: Vanadium in IF Ssteels, Proc. 39th Mechanical Working and Steel Processing Conf., Indianapolis, IN, USA, Oct. 1997, ISS-AIME, Warrendale, PA, 1998, pp. 37–48.
4. W. Al-Shalfan, J. Speer, and D. Matlock: Solubility Products for VC and NbC in Bake Hardenable ULC Steels, ISS 44th Mechanical Working and Steel Processing Conf., Orlando, FL, USA, 2002, ISS-AIME, Warrendale, PA, pp. 615–30.
5. G. Dupuis, R. Hubert, and R. Taillard: A Detailed Study of Sulphide Precipitation in Ti-IF Steels, ISS 40th Mechanical Working and Steel Processing Conf., Pittsburgh, PA, USA, 1998, ISS-AIME, Warrendale, PA, pp. 117–24.
6. D.K. Matlock, B.J. Allen, and J.G. Speer: Modern LC and ULC Sheet Steels for Cold Forming: Processing and Properties, International Symp., Institute of Ferrous Metallurgy, Aachen, 1998, pp. 265–76.
7. W. Al-Shalfan, J. Speer, D. Matlock, H. Ledbetter, and S. Kim: Internal Friction Measurements of Ultra-Low Carbon Sheet Steels, ISS 42nd Mechanical Working and Steel Processing Conf., 2000, pp. 741–53.
8. W. Al-Shalfan: Ph.D. Thesis, Colorado School of Mines, Golden, CO, 2001.
9. Philip Stark, B.L. Averbach, and Morris Cohen: Acta Metall., 1958, vol. 6, pp. 149–55.10.1016/0001-6160(58)90001-4 ↗
10. Y. Wen, Q. Su, and M. Wutting: Interstitial Analysis of Ultra Low Carbon and Interstitial Free Steels, ISS 39th Mechanical Working and Steel Processing Conf., 1997, pp. 271–80.
11. A.J. Jones: Master’s Thesis, Illinois Institute of Technology, Chicago, IL, 1998.
12. M. Shimada and K. Sakamoto: Scripta Metall., 1979, vol. 13, pp. 1177–82.10.1016/0036-9748(79)90278-3 ↗
13. T. Gladman: The Physical Metallurgy of Microalloyed Steels, The Institute of Materials, London, 1997.
14. J.G. Speer, J.R. Michael, and S.S. Hansen: Metall. Trans. A, 1987, vol. 18A, pp. 211–22.10.1007/BF02825702 ↗
15. D. Montgomery and G. Runger: Applied Statistics and Probability for Engineers, 2nd, John Wiley & Sons Inc., New York, NY, 1999.
16. D. McLean: Grain Boundaries in Metals, Oxford at the Clarendon Press, Oxford, United Kingdom, 1957.
17. K. Seto, D.J. Larson, P.J. Warren, and G. Smith: Scripta Mater., 1998, pp. 1029–34.10.1016/S1359-6462(98)00485-0 ↗
18. A. Okamoto, K. Takeuuchi, and M. Takagi: Sumitomo Search, 1989, No. 39, pp. 183–94.
19. K.A. Taylor: Scripta Metall. Mater., 1995, vol. 32, pp. 7–12.10.1016/S0956-716X(99)80002-8 ↗