journal article·2001-06

Cavitation erosion of copper and copper-based alloys

J. Hucińska, M. Głowack

Publisher page

Abstract

Cavitation erosion studies of five multiphase copper-based alloys for a screw propeller application and of three α-solution alloys of comparative purpose have been carried out to determine the resistance of the alloys to cavitation erosion and to understand the influence of the microstructure and/or composition of the alloys on the morphology of erosion damage. The experiments were conducted using a vibratory system. Erosion rates were measured, and the mechanism of damage under cavitation action was studied. No correlation between the cavitation erosion resistance (CER) and the mechanical properties of the alloys has been found. However, a good correlation between the resistance and work-hardenability, defined by means of stacking-fault energy (SFE), being a chemistry-dependent property, has been established for the α-solution alloys. A better CER can be expected for a lower SFE and higher work-hardenability. The resistance of the multiphase alloys in terms of chemical composition and mode of damage was discussed. An advantageous influence of nickel and aluminum and a low effectiveness of zinc on cavitation resistance have been outlined.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Nuclear Materials and Properties · Energetic Materials and Combustion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. B. Vyas and C.M. Preece: J. Appl. Phys., 1976, vol. 47, pp. 5133–38.10.1063/1.322584 ↗
2. B.C.S. Rao and D.H. Buckley: Mater. Sci. Eng., 1984, vol. 67, pp. 55–67.10.1016/0025-5416(84)90031-4 ↗
3. F.J. Heymann: in Characterization and Determination of Erosion Resistance, ASTM STP 474, A. Thiruvengadam and F.J. Heymann, eds., ASTM, Philadelphia, PA, 1970, pp. 212–43.10.1520/STP26871S ↗
4. F.G. Hammitt, C. Chao, C.L. Kling, D.O. Rogers: in Characterization and Determination of Erosion Resistance, ASTM STP 474, A. Thiruvengadam and F.J. Heymann, eds., ASTM, Philadelphia, PA, 1970, pp. 288–317.10.1520/STP26875S ↗
5. G.C. Gould: in Characterization and Determination of Erosion Resistance, ASTM STP 474, A. Thiruvengadam and F.J. Heymann, eds., ASTM, Philadelphia, PA, 1970, pp. 182–211.10.1520/STP26869S ↗
6. E.H.R. Wade and C.M. Preece: Metall. Trans. A, 1978, vol. 9A, pp. 1299–1310.10.1007/BF02652254 ↗
7. D.A. Woodford: Metall. Trans., 1972, vol. 3, pp. 1137–45.10.1007/BF02642445 ↗
8. S. Vaidya and C.M. Preece: Metall. Trans. A, 1978, vol. 9A, pp. 299–307.10.1007/BF02646379 ↗
9. A. Akhtar, R. Salvi, and V.K. Sikka: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 335–43.10.1007/s11661-999-0322-3 ↗
10. J. Hucińska and M. Głowacka: Proc. 3rd Int. Tribology Congr., M. Hebda and C. Kajdas, eds., Technical University of Radom, Radom, Poland 1981, vol. II/A, pp. 75–90.
11. Annual Book of ASTM Standards, ASTM G-32-92 Standard Method of Vibratory Cavitation Erosion Test, ASTM, Philadelphia, PA, 1996, vol. 03.02, pp. 97-110.
12. Publication 7/P, Polish Register of Shipping Regulations, Gdańsk, Poland, 2000.
13. P.C.J. Gallagher: Metall. Trans., 1970, vol. 1, pp. 2429–61.10.1007/BF03038370 ↗
14. J. Hucińska: Ph.D. Thesis, Technical University of Gdańsk, Gdańsk, Poland, 1977.