Near-Neutral pH Stress Corrosion Cracking Susceptibility of Plastically Prestrained X70 Steel Weldment
Source abstract
Abstract
The application of strain-based design for pipelines requires comprehensive understanding of the postyield mechanical behavior of materials. In this article, the impact of plastic prestrain on near-neutral pH stress corrosion cracking (SCC) susceptibility of welded X70 steel was investigated with a slow strain rate tensile (SSRT) test. Generally, plastic prestrain reduces the SCC resistance in various welded zones. The SCC susceptibility of the test materials can be put in the following order: heat-affected zone (HAZ) > weld metal (WM) > base metal (BM). Fractographic analysis indicates that there are two cracking modes, mode I and mode II, during SSRT tests. Mode I cracks propagate along the direction perpendicular to the maximum tensile stress, and mode II cracks lie in planes roughly parallel to the plane where the maximum shear exists. The SCC of the BM is governed by mode I cracking and fracture of the HAZ, and the WM is dominated by mode II cracking. Damage analysis shows that the detrimental impact of plastic prestrain on the residual SCC resistance cannot be evaluated with the linear superposition model. A plastic prestrain sensitivity, a material constant independent of plastic prestrain, is proposed to characterize the susceptibility of SCC resistance to plastic prestrain, and it increases with the SCC susceptibility of the steels. The enhanced SCC susceptibility caused by plastic prestrain may be related to an increase in yield strength. The correlation of the ratio of the reduction in area in NS4 solution to that in air (RA SCC/RA air) with the yield strength is microstructure dependent.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. J.X. Liu: Oil Gas J., 2004, vol. 102, pp. 58–65.
2. Y. Ogawa and T. Koike: Soil Dynamics and Earthquake Engineering, Elsevier, New York, NY, 2001, vol. 21, pp. 199–209.10.1016/S0267-7261(01)00005-7 ↗
3. W. Mohr: “Strain-Based Design of Pipelines,” Report of Project No. 45892GTH to U.S. Department of Interior Management Service and U.S. Department of Transportation, Research and Special Programs Administration, Columbus, OH, 2003.10.55274/R0012120 ↗
4. A.C. Walker: Underwater Technol., 1994, vol. 20, pp. 32–36.
5. M. Kashani and R. Young: J. Transpor. Eng., 2005, vol. 131, pp. 632–39.10.1061/(ASCE)0733-947X(2005)131:8(632) ↗
6. K.R. Jayadevan, E. Ostby, and C. Thaulow: Int. J. Press. Vess. Pip., 2004, vol. 81, pp. 771–83; 2005, vol. 82, pp. 201–15.10.1016/j.ijpvp.2004.04.005 ↗
7. M. Liu, Y.Y. Wang, and D. Horsley: Proc. 24th Int. Conf. on Offshore Mechanics and Arctic Engineering–OMAE, 2005, vol. 3, pp. 385–93.10.1115/OMAE2005-67039 ↗
8. B.T. Lu and J.L. Luo: Corrosion, 2006, vol. 62, pp. 129–40.10.5006/1.3278258 ↗
9. J.F. McCabe and J.W. Oh: Pressure Vessels and Piping Division (Publication) PVP, ASME, New York, NY, 1999, vol. 388, pp. 285–97.
10. B.T. Lu and X.L. Zheng: Iron Steel, 1999, vol. 34, pp. 55–56.
11. R.N. Parkins: Corrosion/2000, NACE INTERNATIONAL, Houston, TX, 2000, Paper 363.
12. R.N. Parkins, W.K. Blanchard, Jr., and B.S. Delandy: Corrosion, 1994, vol. 50, pp. 394–408.10.5006/1.3294348 ↗
13. National Energy Board, Public Inquiry Concerning Stress Corrosion Cracking on Canadian Oil and Gas Pipelines: Report of the Inquiry MH-2-95, National Energy Board, Calgary, Alberta, Canada, 1996.
14. S.D. Liberto and G. Gabetta: Mater. Sci., 1997, vol. 33, pp. 411–20.10.1007/BF02537540 ↗
15. S.X. Mao, B. Gu, N.Q. Wu, and L.J. Qiao: Philos. Mag. A, 2001, vol. 81, pp. 1813–31.10.1080/01418610108216638 ↗
16. B.T. Lu, J.L. Luo, P.R. Norton, and H.Y. Ma: Acta Mater., 2009, vol. 57, pp. 41–49.10.1016/j.actamat.2008.08.035 ↗
17. M. Elboujdaini, Y.-Z. Wang, and R.R. Revie: Proc. Int. Pipeline Conf. (IPC2000), ASME, New York, NY, 2000, vol. 2, pp. 967–85.
18. R.B. Rebak, Z. Xia, R. Safruddin, and Z. Szklarska-Smialowska: Corrosion, 1996, vol. 52, pp. 396–405.10.5006/1.3292126 ↗
19. J.A. Beavers, J.T. Jonson, and R.L. Sutherby: Proc. Int. Pipeline Conf., ASME, New York, NY, 2000, vol. 2, pp. 979–88.
20. B.T. Lu and J.L. Luo: Corrosion, 2006, vol. 62, pp. 129–40.10.5006/1.3278258 ↗
21. K. Poorhaydari and D.G. Ivey: Mater. Sci. Eng. A, 2006, vols. 435–436, pp. 371–82.10.1016/j.msea.2006.07.055 ↗
22. K. Poorhaydari and D.G. Ivey: Mater. Characterization, 2007, vol. 58, pp. 544–54.10.1016/j.matchar.2006.10.017 ↗
23. A.H. Adelek, J.L. Luo, and A.G. Ivey: Northern Area NACE Conf., Saskatoon, Saskatchewan, Canada, Feb. 15–17, 2005.
24. D.A. Jones: Corrosion, 1996, vol. 52, pp. 356–62.10.5006/1.3292123 ↗
25. W. Chen, F. King, T.R. Jack, and M.J. Wilmott: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1429–36.10.1007/s11661-002-0066-9 ↗
26. H. Gao, G.F. Li, X. Cai, R.P. Yang, and W. Yang: J. Mater. Sci. Technol., 2005, vol. 21, pp. 459–64.10.1179/174328405X27034 ↗
27. X.C. Li: Master’s Thesis, University of Alberta, Edmonton, AB, Canada, 2005.
28. E. Maire, C. Bordreuil, L. Babout, and J.-C. Boyer: J. Mech. Phys. Solids, 2005, vol. 53, pp. 2411–34.10.1016/j.jmps.2005.06.005 ↗
29. J.T. Bulger: Master’s Thesis, University of Alberta, Edmonton, AB, Canada, 2000.
30. B.T. Lu and X.L. Zheng: Trans. Chin. Weld. Inst., 1993, vol. 14 (2), pp. 117–24.
31. S.F. Yu, B.N. Qian, and X.M. Guo: Acta Metall. Sinica, 2005, vol. 41, pp. 402–06.
32. X.H. Xue, Y. Zhou, B.N. Qian, J.L. Li, and S.N. Lou: J. Shanghai Jiaotong Univ., 2003, vol. 37, pp. 1854–57.