journal article·2014-01

Plasma Nitriding Behavior of Fe-C-M (M = Al, Cr, Mn, Si) Ternary Martensitic Steels

Yusaku Tomio, Shigeki Kitsuya, Keilchiro Oh-ishi, Kazuhiro Hono, Goro Miyamoto, Tadashi Furuhara

Publisher page

Abstract

Change in surface hardness and nitrides precipitated in Fe-0.6C binary and Fe-0.6 mass pct C-1 mass pct M (M = Al, Cr, Mn, Si) ternary martensitic alloys during plasma nitriding were investigated. Surface hardness was hardly increased in the Fe-0.6C binary alloy and slightly increased in Fe-0.6C-1Mn and Fe-0.6C-1Si alloys. On the other hand, it was largely increased in Fe-0.6C-1Al and Fe-0.6C-1Cr alloys. In all the Fe-0.6C-1M alloys except for the Si-added alloy, fine platelet alloy nitrides precipitated inside martensite laths. In the Fe-0.6C-1Si alloy, Si-enriched film was observed mainly at a grain boundary and an interface between cementite and matrix. Crystal structure of nitrides observed in the martensitic alloys was similar to those in Fe-M binary ferritic alloys reported previously. However, there was a difference in hardening behavior between ferrite and martensite due to a high density of dislocations acting as a nucleation site of the nitrides and partitioning of an alloying element between martensite and cementite changing the driving force of precipitation of the nitrides.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. J. H. Driver and J. M. Papazian: Acta Metall., 1973, vol. 21, pp. 1139-1149.10.1016/0001-6160(73)90030-8 ↗
2. B. Mortimer, P. Grieveson and K. H. Jack: Scand. J. Metall., 1972, vol. 1, pp. 203-209.
3. M. Sennour, P. H. Jouneau and C. Esnouf: J. Mater. Sci., 2004, vol. 39, pp. 4521-4531.10.1023/B:JMSC.0000034146.64444.80 ↗
4. D. H. Jack: Acta Metall., 1976, vol. 24, pp. 137-146.10.1016/0001-6160(76)90016-X ↗
5. D. S. Rickerby and A. Hendry: Acta Metall., 1986, vol. 34, pp. 1911-1923.10.1016/0001-6160(86)90250-6 ↗
6. G. Miyamoto, Y. Tomio, H. Aota, K. Oh-ishi, K. Hono, T. Furuhara: Mater. Sci. Technol., 2011, vol. 27, pp. 742-746.10.1179/1743284710Y.0000000014 ↗
7. M. Pope, P. Grieveson and K. H. Jack: Scand. J. Metall., 1973, vol. 2, pp. 29-34.
8. J. D. Baird: J. Iron Steel Inst., 1966, vol. 204, pp. 1122-1130.
9. B. Jonsson-Holmqvist, P. Grieveson and K. H. Jack: Scand. J. Metall., 1973, vol. 2, pp. 35-38.
10. H. H. Podgurski and H. E. Knechtel: Trans. Metall. Soc. AIME, 1969, vol. 245, pp. 1595-1602.
11. M. H. Biglari, C. M. Brakman and E. J. Mittemeijer: Phil. Mag. A, 1995, vol. 72, pp. 1280-1299.
12. Y. Tomio, G. Miyamoto, T. Furuhara, and T. Maki: Proc. 3rd Int. Conf. Adv. Struct. Steels, 2006, pp. 460–64.
13. S. Mridha and D. H. Jack: Metal Sci., 1982, vol. 16, pp. 398-404.10.1179/msc.1982.16.8.398 ↗
14. N. Ishikawa, T. Shiraga, K. Sato, M. Ishiguro, H. Kabasawa and Y. Kuwahara: Tetsu-to-Hagané, 1996, vol. 82, pp. 164-169.10.2355/tetsutohagane1955.82.2_164 ↗
15. P. Jessner, R. Danoix, B. Hannoyer and F. Danoix: Ultramicroscopy, 2009, vol. 109, pp. 530-534.10.1016/j.ultramic.2008.11.028 ↗
16. B. A. Fuller, R. D. Garwood: J. Iron Steel Inst., 1972, vol. 210, pp. 206-208.
17. G. Kreiner and H. Jacobs: J. Alloys Compounds, 1992, vol. 183, pp. 345-362.10.1016/0925-8388(92)90757-Z ↗
18. E. J. Mittemeijer, M. H. Biglari, A. J. Bottger, N. M. van der Pers, W. G. Sloof and F. D. Tichelaar: Scripta Mater., 1999, vol. 41, pp. 625-630.10.1016/S1359-6462(99)00143-8 ↗
19. Y. Tomio: Ph.D. Thesis, Tohoku University, 2009.10.1587/bplus.2009.8_34 ↗