Grain refinement of superalloy IN718C by the addition of inoculants
Source abstract
Abstract
Suitable inoculants for superalloy IN718C have been selected and prepared. They are composed of two ternary intermetallic compounds: Co3FeNb2 and CrFeNb. Their effects on the structures of superalloy IN718C were investigated. It is found that adding mixed inoculants consisting of Co3FeNb2 and CrFeNb to the melt could significantly refine grains of the γ matrix of superalloy IN718C and increase the proportion of equiaxed grains in cross section, which was theoretically analyzed. In addition, experimental results indicate that trace addition of inoculants to the melt neither introduces inclusions nor changes the phase constituent of the alloy. At the same pouring temperature, the amount of shrinkage porosity in specimens can be greatly decreased if inoculants are added into the melt.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Advanced Materials Characterization Techniques · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. B.A. Ewing and K.A. Green: in Superalloys 1984, M. Gell, C.S. Kortovich, R.H. Bricknell, W.B. Kent, J.F. Radavich, eds., TMS-AIME, Warrendale, PA, 1984, pp. 33–42.
2. M. McLean: Mater. Sci. Technol., 1987, vol. 4, p. 205.10.1179/mst.1988.4.3.205 ↗
3. J.M. Lane: ASM Int. AeroMat93 Conf., Anaheim, CA, June 1993.
4. M. Woulds and H. Benson: in Superalloys 1984, M. Gell, C.S. Kortovich, R.H. Bricknell, W.B. Kent, J.F. Radavich, eds., TMS-AIME, Warrendale, PA, 1984, p. 3.
5. L.F. Mondolfo: in Grain Refinement in Castings and Welds, G.J. Addacshian ed., TMS-AIME, Warrendale, PA, 1983, pp. 3–50.
6. J. Fang and B. Yu: in High Temperature Alloy for Gas Turbines 1982, R. Brunetaud, D. Coutsouradis, T.B. Gibbons, Y. Lindblom, D.B. Meadowcroft, and R. Stickler, eds., D. Reidel Publishing, 1982, p. 987.
7. E. Chang, B. Tseng, J.C. Chou, and V. Yin: AFS Trans., 1988, vols. 88–124, pp. 47–54.
8. K.H. Kloos, K. Stein, and S. Keiser: Metallurgia, 1984, vol. 38 (8), pp. 740–47.
9. J.P. Dennison: in Grain Refinement in Casting and Welds, G.J. Abbaschian and S.A. Davied, eds., TMS-AIME, 1983, pp. 139–49.
10. A.F. Denzine, T.A. Kolakowski, and J.F. Wallace: in AGARD Conference Proceedings, 1982, 325 (12), pp. 5–6.
11. R.M. Cook and A.M. Guthrie: Foundry Trade J., 1966, May, pp. 686–89.
12. Y.H. Xiong, A.M. Yang, Y.P. Guo, W. Liu, and L. Liu: Sci. Technol. Adv. Mater., 2001, No. 2, pp. 13–17.10.1016/S1468-6996(01)00019-5 ↗
13. Y.H. Xiong, W. Liu, A.M. Yang, R. Zhang, and L. Liu: Acta Metall. Sinica, 1999, vol. 35 (7), pp. 689–92.
14. B.L. Bramfitt: Metall. Trans., 1970, vol. 1, p. 1987.10.1007/BF02642799 ↗
15. E.E. Underwood: Metals Handbook, 8th ed., ASM, Metals Park, OH, 1973, vol. 8, p. 37.
16. American National Standards Institute, Standard Methods for Estimating the Average Grain Size of Metals, ASTM Designation e112–74: Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 1977, pp. 207–38.
17. J.D. Hunt: Mater. Sci. Eng., 1984, vol. 65, p. 75.10.1016/0025-5416(84)90201-5 ↗
18. D.Z. Li, S.F. Su, X.H. Xu, J.Q. Wang, J.Z. Chen, and Y.M. Liu: Foundry (China), 1997, Aug., pp. 1–7.