Response of semi-solid Sn-15 pct Pb to rapid shear-rate changes
Source abstract
Abstract
Semisolid metal alloys, used in thixoforming, are thixotropic. The slurry viscosity is shear-rate- and time dependent provided the microstructure in the semisolid state is nondendritic and consists of solid spheroids surrounded by liquid. Thixoforming takes less than 1 second, during which time the structure of the material breaks down. This breakdown can be studied by viscometry, using rapid data-collection rates, by imposing rapid increases in shear rate on the slurry. An initial rapid (<1 second) structural breakdown during a shear-rate jump is followed by a more gradual decrease in viscosity, lasting several minutes. The slurry breaks down more rapidly with a higher final shear rate, but the first breakdown time is independent of the initial shear rate. The reverse is found with the shear-rate drops: recovery times increase with increasing final shear rate. Again, this time is independent of the starting shear rate. The shear stress and viscosity during initial breakdown and initial recovery can be described by single exponential equations. Build-up processes were examined by performing jumps after allowing the slurry to rest at a zero shear rate for different times. The increase in peak stress with rest time reflects the evolving degree of particle agglomeration. Microstructural examination confirms this phenomenon.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. D.B. Spencer, R. Mehrabian, and M.C. Flemings: Metall. Trans., 1972, vol. 3, pp. 1925–32.10.1007/BF02642580 ↗
2. P.A. Joly and R. Mehrabian: J. Mater. Sci., 1976, vol. 11, pp. 1393–1418.10.1007/BF00540873 ↗
3. V. Laxmanan and M.C. Flemings: Metall. Trans. A, 1980, vol. 11, pp. 1927–36.10.1007/BF02655112 ↗
4. H.K. Moon, J.A. Cornie, and M.C. Flemings: Mater. Sci. Eng. A, 1991, vol. 144, pp. 253–65.10.1016/0921-5093(91)90232-C ↗
5. T.Z. Kattamis and A.I. Nakhla: 2nd Int. Conf. on Semi-Solid Processing of Alloys and Composites, Cambridge, MA, S.B. Brown and M.C. Flemings, eds., Massachusetts Institute of Technology Press, Cambridge, MA, 1992, pp. 237–47.
6. L.S. Turng and K.K. Wang: J. Mater. Sci., 1991, vol. 26, pp. 2173–83.10.1007/BF00549185 ↗
7. A.R.A. McLelland: Ph.D. Thesis, Sheffield University, Sheffield, United Kingdom, 1993.
8. P. Kumar, C.L. Martin, and S.B. Brown: Acta Metall. Mater., 1994, vol. 42, pp. 3595–3602.10.1016/0956-7151(94)90426-X ↗
9. C.J. Quaak, M.G. Horsten, and W.H. Kool: Mater. Sci. Eng. A, 1994, pp. 247–56.10.1016/0921-5093(94)90909-1 ↗
10. M.C. Flemings: Metall. Trans. A, 1991, vol. 22A, pp. 957–79.10.1007/BF02661090 ↗
11. D.H. Kirkwood: Int. Mater. Rev., 1994, vol. 39, pp. 173–89.10.1179/imr.1994.39.5.173 ↗
12. P. Kapranos and K.P. Young: Mater. World, 1998, May, pp. 278–80.
13. K.P. Young and P. Eisen: 6th Int. Conf. on Semi-Solid Processing of Alloys and Composites, Turin, Italy, G.L. Chiarmetta and M. Rosso, eds., Edimet Spa, Brescia, Italy, 2000, pp. 97–102.
14. Z. Fan: Int. Mater. Rev., 2002, vol. 47(2), pp. 49–83.10.1179/095066001225001076 ↗
15. P.J. Ward, H.V. Atkinson, and D.H. Kirkwood: 5th Int. Conf. on Semi-Solid Processing of Alloys and Composites. CO, A.K. Bhasin, J.J. Moore, K.P. Young, and S. Midson, eds., Golden, Colorado, Colorado School of Mines, Golden, Colorado, USA, 1998, pp. 115–22.
16. P.J. Ward, H.V. Atkinson, D.H. Kirkwood, S.B. Chin, T.Y. Liu, and M.R. Barkhudarov: Modeling of Casting, Welding and Advanced Solidification Processes—IX, Shaker-Verlag, Aachen, Germany, 2000, P.R. Sahm, P.N. Hansen, and J.G. Conley, eds., 2000, pp. 397–403.
17. T.Y. Liu, P.J. Ward, D.H. Kirkwood, and H.V. Atkinson: XIIIth Int. Congr. on Rheology, Cambridge, United Kingdom, D.M. Binding, N.E. Hudson, J. Mewis, J.-M. Piau, C.J.S. Petrie, P. Townsend, M.H. Wagner, and K. Walters, British Society of Rheology, Glasgow, UK, 2000, vol. 4, pp. 61–63.
18. M.M. Cross: J. Coll. Sci., 1965, vol. 20, pp. 417–37.10.1016/0095-8522(65)90022-X ↗
19. Chambers Science and Technology Dictionary, Chambers, Edinburgh, 1994, p. 755.
20. P. Kumar: Ph.D. Thesis, Massachusetts Institute of Technology, Cambridge, MA, 1994.
21. C.J. Quaak: Ph.D. Thesis, Technische Univesiteit Delft, Delft, The Netherlands, 1996.
22. H. Peng and K.K. Wang: 4th Int. Conf. on Semi-Solid Processing of Alloys and Composites, Sheffield, United Kingdom, D.H. Kirkwood and P. Kapranos, eds., Dept. of Eng. Materials, University of Sheffield, Sheffield, UK, 1996, pp. 2–9.
23. J. Koke and M. Modigell: Proc. Int. Symp. on Advanced Forming and Die Manufacturing Technology, Haeundae-Pusan, Korea, C.G. Kang and Y.H. Moon, eds., Pusan National University, Pusan, Korea, 1999, pp. 101–106.
24. A.R.A. McLelland, N.G. Henderson, H.V. Atkinson, and D.H. Kirkwood: Mater. Sci. Eng. A, 1997, vol. 232, pp. 110–18.10.1016/S0921-5093(97)00105-6 ↗
25. J. Crank: Mathematics of Diffusion, Oxford University Press, London, 1964, p. 9.
26. F. Moore: Trans. Br. Ceram. Soc., 1959, vol. 58, pp. 470–94.
27. M. Mada and F. Ajersch: Mater. Sci. Eng. A, 1996, vol. 212, pp. 157–70.10.1016/0921-5093(96)10212-4 ↗
28. M. Mada and F. Ajersch: Mater. Sci. Eng. A, 1996, vol. 212, pp. 171–77.10.1016/0921-5093(96)10213-6 ↗
29. L. Azzi, F. Ajersch, and T.F. Stephenson: 6th Int. Conf. on Semi-Solid Processing of Alloys and Composites, Turin, Italy, G.L. Chiarmetta and M. Rosso, eds., Edimet Spa, Brescia, Italy, 2000, pp. 527–32.
30. D. Brabazon: Ph.D. Thesis, University College Dublin, Dublin, 2001.