journal article·2010-08

Effect of Aluminum Content on the Microstructure and Mechanical Properties of Hypereutectoid Steels

Yoon Soo Jang, M.P. Phaniraj, Dong-Ik Kim, Jae-Hyeok Shim, Moo-Young Huh

Publisher page

Abstract

Hypereutectoid steels with 0, 0.69, 1.29, and 1.95 wt pct aluminum were prepared. The samples were hot rolled at 1100 °C followed by cooling in air. The microstructure of the as-rolled samples was characterized using field emission–scanning electron microscopy (FE-SEM). The electron backscattered diffraction (EBSD) technique was used to identify the grain boundary phases. The steels have a pearlitic microstructure with different amounts of grain boundary cementite. A continuous grain boundary cementite network is present in the 0 wt pct Al steel. Grain boundary cementite formation is completely suppressed in the 1.29 wt pct Al steel. Phase diagram calculations show that aluminum increases the eutectoid temperature. However, the interlamellar spacing and pearlite colony size decrease with increase in aluminum content. Dilatometry measurements show that aluminum addition increases the undercooling below the eutectoid temperature. The yield strength increases with the decrease in interlamellar spacing and colony size. Very high ultimate tensile strengths (1200 to 1400 MPa) and improved elongations to failure (7 to 9 pct) are achieved in the as-rolled condition.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. E.M. Taleff, J.J. Lewandowski, and B. Pourladian: JOM, 2002, vol. 54, pp. 25–30.10.1007/BF02700982 ↗
2. T. Ochi, S. Nishida, M. Sugiyama, J. Takahashi, and T. Tarui: Nippon Steel Techn. Rep., 2007, No. 96, pp. 5–11.
3. R.W. Heckel and H.W. Paxton: Trans. TMS-AIME, 1960, vol. 218, pp. 799–806.
4. J.A. Wasynczuk, R.M. Fisher, and G. Thomas: Metall. Trans. A, 1986, vol. 17A, pp. 2163–73.10.1007/BF02645914 ↗
5. Y. Kanetsuki, N. Ibaraki, and S. Ashida: ISIJ Int., 1991, vol. 31, pp. 304–11.10.2355/isijinternational.31.304 ↗
6. D.R. Leseur, C.K. Syn, J.D. Whittenberger, and O.D. Sherby: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1559–68.10.1007/s11661-999-0093-x ↗
7. T. Gladman, I.D. McIvor, and F.B. Pickering: J. Iron Steel Inst., 1972, vol. 210, pp. 916–30.
8. J.M. Hyzak and I.M. Bernstein: Metall. Trans. A, 1976, vol. 7A, pp. 1217–24.10.1007/BF02656606 ↗
9. K. Nakase and I.M. Bernstein: Metall. Trans. A, 1988, vol. 19A, pp. 2819–29.10.1007/BF02645816 ↗
10. E.M. Taleff, C.K. Syn, D.R. Lesuer, and O.D. Sherby: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 111–18.10.1007/BF02647751 ↗
11. W.J. Nam, H.R. Song, and C.M. Bae: ISIJ Int., 2005, vol. 45, pp. 1205–10.10.2355/isijinternational.45.1205 ↗
12. N. Ridley: Metall. Trans. A, 1984, vol. 15A, 1019–36.10.1007/BF02644694 ↗
13. K. Han, G.D.W. Smith, and D.V. Edmonds: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1617–31.10.1007/BF02670750 ↗
14. A.M. Elwazri, P. Wanjara, and S. Yue: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 2297–2305.10.1007/s11661-005-0102-7 ↗
15. A.M. Elwazri, P. Wanjara, and S. Yue: ISIJ Int., 2006, vol. 46, pp. 1354–60.10.2355/isijinternational.46.1354 ↗
16. C. Garcia-Mateo, F.G. Caballero, and H.K.D.H. Bhadeshia: ISIJ Int., 2003, vol. 43, pp. 1821–25.10.2355/isijinternational.43.1821 ↗
17. ASTM E112-96, Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2004, vol. 3.01, pp. 1–26.
18. ASTM E8M, Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2008, vol. 3.01, pp. 1–25.
19. W.S. Owen: J. Iron Steel Inst., 1951, vol. 167, pp. 117–20.
20. A.A. Zhukov: Met. Sci., 1978, Nov., pp. 521–24.10.1179/msc.1978.12.11.521 ↗
21. A. Hultgren and K. Kuo: Mem. Etud. Rev. Metall., 1953, vol. 50, p. 847,10.1051/metal/195350120847 ↗
22. W.C. Leslie and G.C. Rauch: Metall. Trans. A, 1978, vol. 9A, pp. 343–49.10.1007/BF02646383 ↗
23. M. Gomez, C.I. Garcia, D.M. Haezebrouck, and A.J. DeArdo: ISIJ Int., 2009, vol. 49, pp. 302–11.10.2355/isijinternational.49.302 ↗
24. A. Pichler, P. Stiaszny, R. Potzinger, R. Tikal, and E. Werner: Proc. 40th MWSP Conf., ISS, Warrendale, 1998, vol. XXXVI, pp. 259–74.
25. H.K.D.H. Bhadeshia: Bainite in Steels, IOM Communications Ltd., London, 2001, pp. 73–74.
26. C. Fossaert, G. Rees, T. Maurickx, and H.K.D.H. Bhadeshia: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 21–30.10.1007/BF02669791 ↗
27. B. Garbarz and F.B. Pickering: Mater. Sci. Technol., 1988, vol. 4, pp. 117–26.10.1179/mst.1988.4.2.117 ↗
28. Y. Palizdar, R.C. Cochrane, R. Brydson, F. Bygrave, and A.J. Scott: J. Phys.: Conf. Ser., 2008, vol. 126, p. 012019.10.1088/1742-6596/126/1/012019 ↗
29. C. Zener: Trans. TMS- AIME, 1946, vol. 167, pp. 550–95.
30. M. Hillert: The Mechanism of Phase Transformation in Crystalline Solids, Institute of Metals, London, 1969, p. 231.
31. M.P. Puls and J.S. Kirkaldy: Metall. Trans., 1970, vol. 3, pp. 2777–96.10.1007/BF02652844 ↗
32. A.R. Marder and B.L. Bramfitt: Metall. Trans. A, 1975, vol. 6A, pp. 2009–14.10.1007/BF03161825 ↗
33. F.B. Pickering: Physical Metallurgy and Design of Steels, Applied Science Publishers Ltd., Essex, England, 1978, p. 90.
34. A.M. Elwazri, P.Wanjara, and S. Yue: Mater. Sci. Eng., 2005, vol. 404A, pp. 91–98.10.1016/j.msea.2005.05.051 ↗