Wear of hard-turned AISI 52100 steel
Source abstract
Abstract
High-precision machining such as hard turning changes the surface and the material properties of steel alloys. The near-surface material properties have been predicted from the known hard-turning cutting conditions. The effect of the predicted hard-turned surface and material properties on wear performance was analyzed in detail to develop a process-performance model. A sliding block-on-cylinder wear tester was used for the purpose of testing the wear performance of AISI 52100 bearing steel. The microstructure, surface roughness, residual-stress field, and loading conditions from each wear test were used to develop the process-performance model. The effect of microstructure on the wear performance of hard-turned steel showed that the white layer and overtempered martensite (OTM) had a higher wear resistance than martensite. The wear-mechanism dependence on the surface hardness was attributed to this increase in wear performance. The near-surface residual stress of the material was shown to become more compressive as the material wore down. The applied normal loads affected the surface roughness, residual stresses, and, in turn, the wear performance of the material. A process-performance model was developed to predict the wear performance of hard-turned steels, which considers the machining process and the operating conditions in sliding wear.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Metal and Thin Film Mechanics · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. E. Rabinowicz: Microstructure and Wear of Materials, John Wiley & Sons, Inc., New York, NY, 1995, pp. 80–124.
2. B.J. Griffiths: J. Tribol., 1987, vol. 109, pp. 525–30.10.1115/1.3261495 ↗
3. B.J. Griffiths: J. Tribol., 1985, vol. 107, pp. 165–71.10.1115/1.3261015 ↗
4. N.S. Akcan: Master’s Thesis, Purdue University, West Lafayette, IN, 1998, pp. 41–51.
5. Y.K. Chou and C.J. Evans. Trans. NAMRI/SME, 1998, vol. 29, pp. 117–22.
6. B.J. Griffiths and D.C. Furze: Trans. ASME, 1987, vol. 109, pp. 388–42.10.1115/1.3248092 ↗
7. Y.Y. Yang, H.S. Fang, and W.G. Huang: Tribol. Int., 1996, vol. 29, pp. 425–28.10.1016/0301-679X(95)00099-P ↗
8. T. Akagaki and K. Kato: Wear, 1990, vol. 141, pp. 1–15.10.1016/0043-1648(90)90187-F ↗
9. J.F. Archard: J. Appl. Phys., 1953, vol. 24, pp. 67–74.10.1063/1.1721448 ↗
10. J.T. Burwell and C.D. Strang: J. Appl. Phys., 1952, vol. 23, pp. 18–28.10.1063/1.1701970 ↗
11. M.B. Peterson and W.O. Winer: Wear Control Handbook, ASME, New York, NY, 1980, pp. 324–408.
12. P.S. Sista: Master’s Thesis, Purdue University, West Lafayette, IN, 1997, pp. 45–66.
13. A.M. Abrao and D. Aspinwall: Wear, 1996, vol. 196, pp. 279–84.10.1016/0043-1648(96)06927-X ↗
14. S. Swain: Ph.D. Thesis, Purdue University, West Lafayette, IN, May 1996, pp. 84–105.
15. I.M. Hutchings: Tribology: Friction and Wear of Engineering Materials, CRC Press, Cambridge, 1992.
16. Z. Gahr and K. Heinz: Microstructure and Wear of Materials, Elsevier, New York, NY, 1987.
17. J.A. Bannantine, J.J. Comer, and J.L. Handrock: Fundamentals of Metal Fatigue Analysis, Prentice-Hall, Elmsford, NJ, 1990, pp. 16–26.
18. H.M. Westergaard: J. Appl. Mech., 1939, June, pp. A49–A53.10.1115/1.4008919 ↗
19. M.P. Szolwinski and T.N. Farris: Wear, 1996, vol. 198, pp. 193–207.10.1016/0043-1648(96)06937-2 ↗