A novel experiment for the study of substrate-induced nucleation in metallic alloys: Application to Zn-Al
Source abstract
Abstract
In order to investigate the nucleation and growth mechanisms of Zn-0.2 wt pct Al grains in thin coatings deposited on steel sheets by hot dipping, a new directional solidification experiment has been specifically designed with a steel substrate immersed into the melt. The competition (CTG) between regular columnar (C) grains growing parallel to the thermal gradient and transverse grains (TGs) nucleated on the sheet surface and growing transversely has been observed in longitudinal sections of Zn-0.2 wt pct Al (-Sb) alloys. Without Sb, the CTG began at midheight of the casting, whereas with Sb, no CTG was found. A simple CTG criterion similar to that of Hunt for the columnar-to-equiaxed Transition (CET) was derived. The calculated extension of the TGs was successfully compared with that measured on micrographs reconstructed from electron backscattered diffraction (EBSD) measurements. This indicated that the critical nucleation undercooling for the formation of Zn-0.2 wt pct Al grains on the steel sheet is about 0.7 K and that Sb poisons these available nucleation sites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. J. Strutzenberger and J. Faderl: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 631–46.10.1007/s11661-998-0144-8 ↗
2. D.I. Cameron and G.J. Harvey: Proc. 8th Int. Conf. on Hot Dip Galvanizing, Zinc Development Association, London, 1967, pp. 86–97.
3. N.J. Wall, J.A. Spittle, and R.D. Jones: Proc. 1st Int. Conf. on Zinc Coated Steel Sheet, Zinc Development Association, London, 1985, pp. C1-C6.
4. F.A. Fasoyinu and F. Weinberg: Metall. Mater. Trans. B, 1990, vol. 21B, pp. 549–58.10.1007/BF02667868 ↗
5. A. Sémoroz, S. Henry, and M. Rappaz: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 487–95.10.1007/s11661-000-0284-y ↗
6. A. Sémoroz, L. Strezov, and M. Rappaz: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2685–94.10.1007/s11661-002-0390-0 ↗
7. A. Sémoroz: Doctoral Thesis, Ecole Polytechnique Fédérale de Lausanne, Lausanne, Switzerland, 2001.
8. A.M. Bunn, P. Schumacher, M.A. Kearns, C.B. Boothroyd, and A.L. Greer: Mater. Sci. Technol., 1999, vol. 15 (10), pp. 1115–23.10.1179/026708399101505158 ↗
9. A. Sémoroz, L. Strezov, and M. Rappaz: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2695–2701.10.1007/s11661-002-0391-z ↗
10. J.D. Hunt: Mater. Sci. Eng., 1984, vol. 65, pp. 75–83.10.1016/0025-5416(84)90201-5 ↗
11. C.-A. Gandin, J.-L. Desbiolles, M. Rappaz, and P. Thévoz: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3153–65.10.1007/s11661-999-0226-2 ↗
12. S. Henry, T. Minghetti, and M. Rappaz: Acta Mater., 1998, vol. 46 (18), pp. 6431–43.10.1016/S1359-6454(98)00308-5 ↗
13. T. Campanella, C. Charbon, and M. Rappaz: 7th Eur. Conf. on Advanced Materials and Proc. Euromat 2001, Rimini, Italy, 2001 (CD-ROM).
14. CALCOSOFT®2D: User Manual, Calcom SA, Lausanne, Switzerland, 2002.
15. J.-M. Drezet, M. Rappaz, G.-U. Grün, and M. Gremaud: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1627–34.10.1007/s11661-000-0172-5 ↗
16. T.W. Clyne and W. Kurz: Metall. Trans. A, 1981, vol. 12 (6), pp. 965–71.10.1007/BF02643477 ↗
17. A.R. Marder: Progr. Mater. Sci., 2000, vol. 45, pp. 191–271.10.1016/S0079-6425(98)00006-1 ↗
18. W. Kurz, B. Giovanola, and R. Trivedi: Acta Metall., 1986, vol. 34 (5), pp. 823–30.10.1016/0001-6160(86)90056-8 ↗