Three Important Points that Relate to Improving the Hot Workability of Ledeburitic Tool Steels
Source abstract
Abstract
In this article, the importance of selecting the right process parameters for ledeburitic tool steels, i.e., casting temperature, cooling rate, and soaking temperature, which is needed to improve their intrinsic hot workability, is presented. The results were obtained from investigations in industrial practice and in the laboratory. It was found that inappropriate selection of these process parameters results in the occurrence of carbides that are not usually present in these types of steels, in terms of type, shape, fractions, and their distribution that decreases the steels’ hot workability. In particular, a casting temperature that is too high and cooling rates that are too low result in the additional precipitation of carbides, which are not common in these steels, leading to cracking, predominately along these carbide stringers and consequently to a deterioration of the hot workability and the properties of the final products. It was also found that by selecting the proper soaking conditions, it is possible to decrease the negative influence of previous processing parameters on the hot workability.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. G. Roberts, G. Krauss, and R. Kennedy: Tool Steels, 5th ed., ASM International, Materials Park, OH, 1998.10.31399/asm.tb.ts5.9781627083584 ↗
2. C. Imbert, N.D. Ryan, and H.J. McQueen: Metall. Trans. A, 1984, vol. 15A, pp. 1855–64.10.1007/BF02664899 ↗
3. R. Milovic, D. Manojlovic, M. Andjelic, and D. Drobnjak: Steel Res., 1992, vol. 63, no. 2, pp. 78–84.10.1002/srin.199200474 ↗
4. K. Osaki, M. Yano, and T. Yoshida: 7 th ISPS Symp., Tsukuba, Japan, 1997, pp. 111–18.
5. C.A.C. Imbert and H.J. McQueen: Mater. Sci. Technol., 2000, vol. 16, pp. 532–38.10.1179/026708300101508036 ↗
6. C.A.C. Imbert and H.J. McQueen: Mater. Sci. Technol., 2000, vol. 16, no. 5, pp. 524–31.10.1179/026708300101508199 ↗
7. H.J. McQueen and C.A.C. Imbert: Processing and Properties of Structural Materials, E.M. Tallef, C.K. Syn, and D.R. Lesuer, eds., TMS, Warrendale, PA, 2000, pp. 79–92.
8. J. Liu, H. Chang, R. Wu, T.Y. Hsu, and X. Ruan: Mater. Charact., 2000, vol. 45, pp. 175–86.10.1016/S1044-5803(00)00071-1 ↗
9. C.A.C. Imbert and H.J. McQueen: Mater. Sci. Eng. A, 2001, vol. 313, pp. 104–16.10.1016/S0921-5093(01)00974-1 ↗
10. C.A.C. Imbert and H.J. McQueen: Can. Metall. Q., 2001, vol. 40, pp. 235–44.10.1179/000844301794388461 ↗
11. M.R. Ghomashchi and C.M. Sellars: Metall. Trans. A, 1993, vol. 24A, pp. 2171–80.10.1007/BF02648591 ↗
12. C. Rodenburg, M. Kryzanowski, J.H. Beynon, and W.M. Rainforth: Mater. Sci. Eng. A, 2004, vol. 386, pp. 420–27.10.1016/S0921-5093(04)01002-0 ↗
13. R. Thome and W. Dahl: Steel Res., 1995, vol. 66, no. 2, pp. 63–71.10.1002/srin.199501089 ↗
14. M. Spittel, C. Weiß, and T. Spittel: Neue Hütte, 1991, vol. 36, no. 8, pp. 284–89.
15. N. Imai, N. Komatsubara, and K. Kunishihe: ISIJ Int., 1997, vol. 37, no. 3, pp. 217–23.10.2355/isijinternational.37.217 ↗
16. C.C. Szilvassy and W.C.K. Wong: J. Mater. Process. Tech., 1992, vol. 29, pp. 191–202.10.1016/0924-0136(92)90434-T ↗
17. H. Brandis, E. Haberling, and H.H. Weigard: Processing and Properties of High Speed Tool Steels, M.G.H. Wells and L.W. Lherbier, eds., TMS-AIME, Warrendale, PA, 1980, pp. 1–18.
18. D.W. Hetzner and W. Van Geertruyden: Mater. Charact., 2008, vol. 59, pp. 825–41.10.1016/j.matchar.2007.07.005 ↗
19. T. Večko-Pirtovšek, M. Fazarinc, G. Kugler, P. Mrvar, and M. Terčelj: RMZ- Mater. Geoenviron., 2011, vol. 58, no. 2, pp. 113–20.
20. B. Bradaškja, J. Koruza, M. Fazarinc, M. Knap, and R. Turk: RMZ-Mater. Geoenviron., 2008, vol. 55, no. 1, pp. 31–40.
21. T. Večko-Pirtovšek, G. Kugler, M. Godec, and M. Terčelj: Mater. Charact., 2011, vol. 62, no. 2, pp. 189–97.10.1016/j.matchar.2010.11.016 ↗
22. R. Riedl, S. Karagöz, H. Fischmeister, and F. Jeglitsch: Steel Res., 1987, vol. 58, no. 8, pp. 339–51.10.1002/srin.198700230 ↗
23. A. Tauqir, H. Nowotny, and P.R. Strutt: Metall. Trans. A, 1990, vol. 21A, pp. 3021–28.10.1007/BF02647222 ↗
24. D. Peidao, S. Gongqi, and Z. Shouze: Mater. Charact., 1992, vol. 29, pp. 15–24.10.1016/1044-5803(92)90091-U ↗
25. E. Kalinushkin, I. Mamusich, and J. Taran: Metalurgija, 1999, vol. 38, no. 3, pp. 137–41.
26. A.K. Bhargava and A.N. Tiwari: Int. J. Rapid Solid., 1992, vol. 7, pp. 51–66.
27. A.V. Supov, N.M. Aleksandrova, S.A. Paren’kov, R.V. Kakabadze, and V.P. Pavlov: Met. Sci. Heat Treat., 1998, vol. 40, nos. 9-10, pp. 354–59.10.1007/BF02466239 ↗
28. D.H. Hetzner: Mater. Charact., 2001, vol. 46, pp. 175–82.10.1016/S1044-5803(01)00121-8 ↗
29. H.F. Fischmeister, R. Riedl, and S. Karagöz: Metall. Trans. A, 1989, vol. 20A, pp. 2133–48.10.1007/BF02650299 ↗
30. K.C. Hwang, S. Lee, and H.C. Lee: Mater. Sci. Eng. A, 1998, vol. 254, pp. 282–95.10.1016/S0921-5093(98)00626-1 ↗
31. M. Boccalini and H. Goldenstein: Int. Mater. Rev., 2001, vol. 46, no. 2, pp. 92–115.10.1179/095066001101528411 ↗
32. Y. Luan, N. Song, Y. Bai, X. Kang, and D. Li: J. Mater. Process. Tech., 2010, vol. 210, pp. 536–41.10.1016/j.jmatprotec.2009.10.017 ↗
33. S. Karagöz and H. Fischmeister: Steel Res., 1987, vol. 58, no. 8, pp. 353–61.10.1002/srin.198700231 ↗
34. P. Ding, G. Shi, and S. Zhou: Metall. Trans. A, 1993, vol. 24A, pp. 1265–72.10.1007/BF02668195 ↗
35. M.R. Ghomashchi: Acta Mater., 1998, vol. 46, no. 14, pp. 5207–20.10.1016/S1359-6454(98)00110-4 ↗
36. H. Di, X. Zhang, G. Wang, and X. Liu: J. Mater. Process. Tech., 2005, vol. 166, pp. 359–63.10.1016/j.jmatprotec.2004.07.085 ↗
37. X. Zhang, W. Liu, D. Sun, and Y. Li: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 499–505.10.1007/s11661-006-9071-8 ↗