Deformation and fracture of a particle-reinforced aluminum alloy composite: Part II. Modeling
Source abstract
Abstract
In this article, the tensile and fracture properties of a discontinuously reinforced aluminum (DRA) alloy composite are modeled to determine the influence of constituent parameters on material behavior. Comparison of the elastic-modulus calculations to the experimental data suggest that the angular particles are more effective in load transfer than spherical particles, and that a unit cylinder geometry is a good representation of the particles under elastic conditions. This same geometry is used in the finite element-based elastic-plastic model of Bao et al., and reasonably good agreement is obtained between the experimental and predicted yield strengths. A fracture-mechanics model is proposed for predicting the elongation to failure. The model assumes the existence of particle cracks, and criticality is based on the strain required for matrix rupture between cracked particles. The damage criterion of Cockcroft and Latham is utilized, and model predictions are compared to data from different investigations. It is shown that the volume fraction of particles and the work-hardening coefficient of the matrix have a strong influence on the strain to failure. Fracture toughness modeling one again exposes the limitations of existing zero-degree crack-propagation models, such as that of Hahn and Rosenfield, which predict increased toughness with yield strength rather than a decrease, which is observed experimentally. A shear-failure model along a 45-deg direction is proposed for the higher-strength conditions, where concentrated slip bands were observed. The model exhibits the inverse toughness dependence on strength and better correlation to peak-aged (PA) data, but shows poorer agreement with underaged (UA) data. Thus, a transition from zero-degree propagation to 45-deg propagation with increasing strength is suggested. A simplified method for extracting particle stresses is illustrated and is used to estimate a Weibull modulus of 4.9 and a Weibull strength of 2450 MPa for the SiC particles of an average diameter of 10 μm.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Composite Material Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. B. Budiansky: J. Mech. Phys. of Solids, 1965, vol. 13, 223.10.1016/0022-5096(65)90011-6 ↗
2. Y.L. Shen, M. Finot, A. Needleman, and S. Suresh: Acta Metall., 1994, vol. 42, pp. 77–97.10.1016/0956-7151(94)90050-7 ↗
3. G. Bao, J.W. Hutchinson, and R.M. McMeeking: Acta Metall., 1991, vol. 39, pp. 1871–82.10.1016/0956-7151(91)90156-U ↗
4. J. Llorca, A. Martin, J. Ruiz, and M. Elices: Metall. Trans. A, 1993, vol. 24A, pp. 1575–88.10.1007/BF02646597 ↗
5. D.B. Zahl and R.M. McMeeking: Acta Metall., 1991, vol. 39, pp. 1117–22.10.1016/0956-7151(91)90199-B ↗
6. J.D. Evensen and A.S. Verk: Scripta Metall., 1981, pp. 1131–33.10.1016/0036-9748(81)90173-3 ↗
7. L.M. Brown and J.D. Embury: Proc. ICSMA III, Cambridge, Institute of Metals, United Kingdom, 1973, pp. 164–68.
8. K. Tanaka, T. Mori, and T. Nakamura: Phil. Mag., 1970, vol. 21, pp. 267–79.10.1080/14786437008238415 ↗
9. M.G. Cockcroft and D.J. Latham: J. Inst. Met., 1968, vol. 96, pp. 33–39.
10. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill, New York, NY, 1986.
11. R.M. McMeeking: J. Mech. Phys. Solids, 1977, vol. 25, pp. 357–81.10.1016/0022-5096(77)90003-5 ↗
12. V. Kumar, M.D. German, and C.F. Shih: Technical Report No. EPRI NP 1931. Electric Power Research Institute, Palo Alto, CA, 1981.
13. T.W. Clyne and P.J. Withers: An Introduction to Metal Matrix Composites, Cambridge University Press, Cambridge, United Kingdom, 1993.10.1017/CBO9780511623080 ↗
14. T. Christman, A. Needleman, and S. Suresh: Acta Metall., 1989, vol. 37, pp. 3029–50.10.1016/0001-6160(89)90339-8 ↗
15. J. Llorca and M. Elices: in Intrinsic and Extrinsic Fracture Mechanisms in Inorganic Composite Systems, J.J. Lewandowski and W.H. Hunt, Jr., eds., TMS, Warrendale, PA, 1995, pp. 15–24.
16. J. Orr and D.K. Brown: Eng. Fract. Mech., 1974, vol. 6, pp. 261–74.10.1016/0013-7944(74)90024-1 ↗
17. D.J. Lloyd: Acta Metall., 1991, vol. 39, pp. 59–71.10.1016/0956-7151(91)90328-X ↗
18. B.S. Majumdar, T.E. Matikas, and D.B. Miracle: Composites: Part B, 1998, vol. 29B, pp. 131–45.10.1016/S1359-8368(97)00004-8 ↗
19. B.S. Majumdar, S.G. Warrier, and D.B. Miracle: MRS Symp. on Interfacial Engineering for Optimized Properties, C.L. Briant, E.L. Hall, and C.B. Carter, eds., Materials Research Society, Pittsburgh, PA, 1997, pp. 185–90.
20. C.A. Lewis and P.J. Withers: Acta Metall., 1995, vol. 43, pp. 3685–99.10.1016/0956-7151(95)90152-3 ↗
21. G.T. Hahn and A.R. Rosenfield: Metall. Trans. A, 1975, vol. 6A, pp. 653–70.10.1007/BF02672285 ↗
22. S.V. Kamat, J.P. Hirth, and R. Mehrabian: Acta Metall., 1989, vol. 37, p. 2395.10.1016/0001-6160(89)90037-0 ↗
23. M. Manoharan and J.J. Lewandowski: Acta Metall., 1990, vol. 38, pp. 489–96.10.1016/0956-7151(90)90155-A ↗
24. A.B. Pandey, B.S. Majumdar, and D.B. Miracle: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1237–43.10.1007/s11661-998-0250-7 ↗
25. J.R. Rice and M.A. Johnson: In Inelastic Behavior of Solids, M.F. Kanninen, W.F. Adler, A.R. Rosenfield, and R.I. Jaffee, eds., McGraw-Hill, New York, NY, Battelle Memorial Institute, Columbus, OH, 1969, pp. 641–72.
26. R.O. Ritchie and A.W. Thompson: Metall. Trans. A, 1985, vol. 16A, pp. 233–48.10.1007/BF02815305 ↗
27. J.R. Rice and D.M. Tracey: J. Mech. Phys. Solids, 1969, vol. 17, pp. 201–17.10.1016/0022-5096(69)90033-7 ↗
28. C.F. Shih: J. Mech. Phys. Solids, 1981, vol. 29, pp. 305–26.10.1016/0022-5096(81)90003-X ↗
29. R. Everett: 1997, private communications.
30. G.G. Garrett and J.F. Knott: Metall. Trans. A, 1978, vol. 9A, pp. 1187–201.10.1007/BF02652242 ↗
31. G.T. Hahn and A.R. Rosenfield: Applications Related Phenomena in Titanium Alloys, ASTM STP 432, ASTM, Philadelphia, PA, 1968, pp. 5–32.10.1520/STP33617S ↗
32. C.D. Beachem and G.R. Yoder: Metall. Trans., 1973, vol. 4, pp. 1145–53.10.1007/BF02645619 ↗
33. J.Q. Clayton and J.F. Knott: Met. Sci., 1976, pp. 63–71.10.1179/030634576790432083 ↗
34. K.V. Jata and E.A. Starke: Metall. Trans. A, 1986, vol. 17A, pp. 1011–26.10.1007/BF02661267 ↗
35. S. Ghosh and S. Moorthy: Acta Metall., 1998, vol. 46, pp. 965–82.
36. A.B. Pandey, B.S. Majumdar, and D.B. Miracle: Mater. Sci. Eng., 1999, vol. A259, pp. 296–307.10.1016/S0921-5093(98)00901-0 ↗
37. A.L. Geiger and J.A. Walker: J. Met., 1991, vol. 43, pp. 8–15.
38. A. Mortensen: Proc. Int. Conf., Montreal, Canada, 1990, ASM INTERNATIONAL, Materials Park, OH, pp. 217–33.
39. W.H. Hunt: in Intrinsic and Extrinsic Mechanisms in Inorganic Composite Systems, J.J. Lewandowski and W.H. Hunt, eds., TMS, Warrendale, PA, 1995, pp. 31–38.
40. W.H. Hunt, T.M. Osman, and J.J. Lewandowski: J. Met., 1993, vol. 45, pp. 30–35.
41. J.R. Rice: Proc. 3rd Int. Conf. on Fracture, ICF-3, T. Yokobori, T. Kawasaki, and J.L. Swedlow, eds., Sendai, Japan, Japanese Society for Strength and Fracture, 1965, pp. 309–400.