Evaluation of the fatigue behavior of ductile irons with various matrix microstructures
Source abstract
Abstract
The stress-failure (S-N) curves for ferritic irons, pearlitic irons, and austempered ductile irons (ADIs) have been determined under tension-tension loading with a stress ratio of 0.1. The effects of Ti contents of up to 0.10 wt pct (resulting from the deliberate use of Ti-containing steel scrap) on fatigue behavior were investigated. It was found that ferritic and pearlitic ductile irons can contain up to 0.10 wt pct Ti without any adverse effect on fatigue behavior. In ADIs, fatigue properties deteriorate at such high Ti contents. Tests were also conducted to investigate the effects of microstructural features on fatigue properties. It was found that the effect of the graphite nodule count (the number of graphite particles on a unit area of a polished surface) on the fatigue limit is significant only in ADIs. Scanning electron microscope (SEM) analysis has shown that cracks usually initiate from surface dross-type defects. However, in ADIs, fatigue cracks can also initiate at shrinkage cavities and at surface or subsurface locations. An offset bilinear S-N curve behavior (the linear S-N curve at higher stress levels is separated from the linear S-N curve at lower stress levels) has been observed in ADIs. This is attributed to surface residual compressive stresses, which prohibit fatigue crack initiation from surface positions at lower applied stress levels. In ferritic and pearlitic ductile irons, the offset bilinear S-N curve behavior is not observed because of the rapid relaxation of the residual compressive stresses.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. K. Ikawa and J. Ohide: AFS Trans., 1984, vol. 92, pp. 45–53.
2. H. Morrogh: J. Iron Steel Inst., 1941, vol. 1, pp. 207–86.
3. J.R. Hitchings and J. Klein: AFS Trans., 1989, vol. 97, pp. 579–86.
4. C.R. Loper, R.C. Voigt, J.R. Yang, and G.X. Sun: AFS Trans., 1981, vol. 89, pp. 529–42.
5. G.X. Sun and C.R. Loper: AFS Trans., 1983, vol. 91, pp. 639–46.
6. H. Morrogh: AFS Trans., 1952, vol. 60, pp. 439–52.
7. J.V. Dawson: BCIRA J., 1956, vol. 6, pp. 180–83.
8. T. Watmough, W.F. Shaw, and F.C. Bock: AFS Trans., 1971, vol. 79, pp. 225–46.
9. I. Riposan, M. Chisamera, and L. Sofroni: Cast Met., 1990, vol. 2, pp. 207–13.10.1080/09534962.1989.11819005 ↗
10. C.E. Bates and J.F. Wallace: AFS Trans., 1967, vol. 75, pp. 815–38.
11. J.H. Davidson and C. Aubin: High Temperature Alloys for Gas Turbines—Conf. on High Temperature Alloys for Gas Turbines, R. Brunetaud, D. Coutsouradis, T.B. Gibbons, Y. Lindblom, D.B. Meadowcroft, and R. Stickler, eds., Kluwer Academic Publishers, Hardbound, 1982, pp. 791–804.
12. D. Venugopalan and K.L. Pilon: AFS Trans., 1988, vol. 96, pp. 697–704.
13. M. Sofue, S. Okada, and T. Sasaki: AFS Trans., 1978, vol. 86, pp. 173–82.
14. M. Sofue: Imono (J. JFS), 1976, vol. 48, pp. 29–45.
15. P.R. Khan, W.M. Su, H.S. Kim, J.W. Kang, and J.F. Wallace: AFS Trans., 1987, vol. 95, pp. 105–16.
16. P.R. Khan, W.M. Su, H.S. Kim, J.W. Kang, T.V. Johnson, and J.F. Wallace: Foundryman, 1987, pp. 237–44.
17. Y. Ochi, A. Ishii, S.K. Sasaki, and Y. Konishi: Mechanical Behavior of Materials—VI, Proc. 6th Int. Conf., Pergamon Press Ltd., Oxford, 1991, vol. 4, pp. 313–18.
18. P. Clement, J.P. Angeli, and A. Pineau: Fatigue Eng. Mater. Struct., 1984, vol. 7, pp. 251–65.10.1111/j.1460-2695.1984.tb00194.x ↗
19. Y. Tanaka, Z.L. Yang, and K. Miyamoto: Mater. Trans., JIM, 1995, vol. 36, pp. 749–56.10.2320/matertrans1989.36.749 ↗
20. Y. Nadot, N. Ranganathan, J. Mendez, and A.S. Beranger: Fatigue ’96, Pergamon Press Ltd., Oxford, 1996, vol. 1, pp. 239–44.
21. G.P. Faubert, D.J. Moore, and K.B. Rundman: AFS Trans., 1991, vol. 99, pp. 563–70.
22. G.P. Faubert, D.J. Moore, and K.B. Rundman: AFS Trans., 1990, vol. 98, pp. 759–64.
23. J.F. Janowak and A. Algarsamy: AFS Trans., 1990, vol. 98, pp. 511–18.
24. T.R. Farrel: AFS Trans., 1983, vol. 91, pp. 61–64.
25. A.G. Fuller: AFS Trans., 1977, vol. 85, pp. 527–36.
26. D. Krishnaraji, K.V. Rao, and S. Seshan: AFS Trans., 1989, vol. 97, pp. 345–50.
27. M. Castagna, P. Ferrero, R. Medana, and E. Natale: AFS Trans., 1978, vol. 86, pp. 573–82.
28. W. Renzhi: Fatigue Eng. Mater. Struct., 1979, vol. 2, pp. 413–18.10.1111/j.1460-2695.1979.tb01098.x ↗
29. G.H. Farrahi, J.L. Lebrun, and D. Couratin: Fatigue Fract. Eng. Mater. Struct., 1995, vol. 18, pp. 211–20.10.1111/j.1460-2695.1995.tb00156.x ↗
30. Y. Mutoh, G.H. Fair, B. Noble, and R.B. Waterhouse: Fatigue Fract. Eng. Mater. Struct., 1987, vol. 10, pp. 261–72.10.1111/j.1460-2695.1987.tb00205.x ↗
31. F.S. Ahmed: Modelling, measurement and Control C: Energetics, Chemistry, Earth, Environmental and Biomedical Problems, AMSE Press, Tassin-la-Demi-Lune, France, 1995, vol. 47 (1–3), pp. 29–42.
32. J.L. Doong, J.R. Hwang, and H.S. Chen: J. Mater. Sci., 1986, vol. 21, pp. 871–78.10.1007/BF01117367 ↗
33. D.W. Becker and J.A. Psihoyious: Internal Combustion Engine Division (publication) ICE, ASME, New York, NY, 1986, vol. 1, pp. 59–64.
34. K. Saruki, A. Yamada, and K. Ogawa: J. Soc. Mater. Sci. Jpn., 1988, vol. 37, pp. 631–36.10.2472/jsms.37.631 ↗
35. H. Suzuki, A. Magata, W.M. Gong, and Y. Ito: Trans. Jpn. Soc. Mech. Eng., 1995, vol. A61, pp. 2349–54.10.1299/kikaia.61.2349 ↗
36. H. Suzuki, K. Ito, S. Nishino, S. Yamada, and M. Moriya: Trans. Jpn. Soc. Mech. Eng., 1996, vol. A62, pp. 627–31.10.1299/kikaia.62.627 ↗
37. A. Kiciak, G. Glink, and D.J. Burns: Fatigue ’96, Pergamon Press Ltd., Oxford, 1996, vol. 1, pp. 1207–13.
38. P. Starker, H. Wohlfahrt, and E. Macherauch: Fatigue Eng. Mater. Struct., 1979, vol. 1, pp. 319–27.10.1111/j.1460-2695.1979.tb00388.x ↗
39. P. Forget, M. Jeandin, and A. Lyoret: J. De Phys. IV, 1993, vol. 2, pp. 921–26.
40. H. Sunada: Iron Steel Inst. Jpn. Int., 1993, vol. 33, pp. 321–27.10.2355/isijinternational.33.321 ↗
41. NF EN ISO 945 (A32-100), Fonte-Designation de la Microstructure du Graphite (Cast Iron-Designation of Microstructure of Graphite), 1994.
42. R.L. Miller: ASM Trans., 1964, vol. 57, pp. 892–99.
43. Y. Tanaka and H. Kage: Mater. Trans., JIM, 1992, vol. 33(6), pp. 543–57.10.2320/matertrans1989.33.543 ↗
44. T. Kobayashi and H. Yamamoto: AFS Trans., 1991, vol. 99, pp. 263–71.
45. J.F. Janowak and R.B. Gundalach: AFS Trans., 1983, vol. 91, pp. 377–88.
46. M. Nili Ahamadabadi, E. Niyama, and T. Ohide: AFS Trans., 1994, vol. 102, pp. 269–78.
47. Y. Nadot, N. Ranganathan, J. Mendez, and A.S. Beranger: Fatigue ’96, Pergamon Press Ltd., Oxford, 1996, vol. 1, pp. 331–36.
48. Shigeru Doi, Kazumichi, Masao Takahara, and Katsuyuki Sato: Fatigue ’96, Pergamon Press Ltd., Oxford, 1996, vol. 1, pp. 245–50.
49. M. Johanson: AFS Trans., 1977, vol. 85, pp. 117–22.
50. Leslie Bartosiewicz, A.R. Krause, F.A. Alberts, Iqbac Singh, and Susil K. Putatunda: Mater. Characterisation, 1993, vol. 30, pp. 221–34.10.1016/1044-5803(93)90069-8 ↗