The role of melt pool behavior in free-jet melt spinning
Source abstract
Abstract
The influence of melt pool behavior on the competition between the nucleation of crystalline solidification products and glass formation is examined for an Fe-Si-B alloy. High-speed imaging of the melt pool, analysis of ribbon microstructure, and measurement of ribbon geometry and surface character all indicate upper and lower limits for melt spinning (MS) rates for which fully amorphous ribbons can be achieved. Comparison of the relevant time scales reveals that surface-controlled melt pool oscillation may be the dominant factor governing the onset of unsteady thermal conditions accompanied by varying amounts of crystalline nucleation observed near the lower limit. At high rates, the influence of these oscillations is minimal due to very short melt pool residence times. However, microstructural evidence suggests that the entrapment of gas pockets at the wheel-metal interface may play a critical role in establishing the upper rate limit. An observed transition in wheel-side surface character with an increasing MS rate supports this contention.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallic Glasses and Amorphous Alloys · Solidification and crystal growth phenomena · Material Dynamics and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. R. Mehrabian: in Rapid Solidification Processing: Principles and Technologies, R. Mehrabian, B.H. Kear, and M. Cohen, eds., Claitor’s Publishing, Baton Rouge, LA, 1977, pp. 9–27.
2. R. Trivedi and W. Kurz: Int. Mater. Rev., 1994, vol. 39 (2), pp. 49–74.10.1179/imr.1994.39.2.49 ↗
3. P. Duwez, R.H. Willens, and W. Klement: J. Appl. Phys., 1960, vol. 31, pp. 1136–37.10.1063/1.1735777 ↗
4. W. Klement, R.H. Willens, and P. Duwez: Nature, 1960, vol. 187, pp. 869–70.10.1038/187869b0 ↗
5. F.E. Luborsky: IEEE Trans. Magn., 1978, vol. 14 (5), pp. 1008–12.10.1109/TMAG.1978.1060018 ↗
6. R.C. O’Handley and H.H. Liebermann: in Elements of Rapid Solidification: Fundamentals and Applications, M.A. Otooni, ed., Springer Series in Materials Science, Springer, Berlin, 1998, vol. 29, pp. 153–86.10.1007/978-3-642-45755-5_6 ↗
7. H. Jones: in Rapid Solidification Processing: Principles and Technologies, R. Mehrabian, B.H. Kear, and M. Cohen, eds., Claitor’s Publishing, Baton Rouge, LA, 1977, pp. 28–45.
8. S. Kavesh: in Metallic Glasses, J. Gilman and H. Leamy, eds., ASM, Metals Park, OH, 1978, pp. 36–73.
9. K. Takeshita and P.H. Shingu: Trans. JIM, 1983, vol. 24 (7), pp. 293–300.10.2320/matertrans1960.24.293 ↗
10. K. Takeshita and P.H. Shingu: Trans. JIM, 1983, vol. 24 (7), pp. 529–36.10.2320/matertrans1960.24.529 ↗
11. G.X. Wang and E.F. Matthys: Int. J. Rapid Solidification, 1991, vol. 6, pp. 141–74.
12. G.X. Wang and E.F. Matthys: Modelling Simul. Mater. Sci. Eng., 2002, vol. 10, pp. 35–55.10.1088/0965-0393/10/1/304 ↗
13. Z. Sun and H.A. Davies: Mater. Sci. Eng., 1988, vol. 98, pp. 71–74.10.1016/0025-5416(88)90129-2 ↗
14. T.W. Clyne: Metall. Trans. B, 1984, vol. 15B, pp. 369–81.10.1007/BF02667341 ↗
15. E.M. Gutierrez and J. Szekely: Metall. Trans. B, 1986, vol. 17B, pp. 695–703.10.1007/BF02657132 ↗
16. X. Zhang and A. Atrens: Mater. Sci. Eng. A, 1992, vol. A159, pp. 243–51.10.1016/0921-5093(92)90295-C ↗
17. L. Granasy: Mater. Sci. Eng. A, 1989, vol. A111, pp. 129–44.10.1016/0921-5093(89)90205-0 ↗
18. T.R. Anthony and H.E. Cline: J. Appl. Phys., 1979, vol. 50 (1), pp. 245–54.10.1063/1.325708 ↗
19. M.E. Frazer, W.K. Lu, A.E. Hamielec, and R. Murarka: Metall. Trans., 1971, vol. 2, pp. 817–23.10.1007/BF02662741 ↗
20. R. Murarka, W.K. Lu, and A.E. Hamielec: Can. Metall. Q., 1975, vol. 14 (2), pp. 111–15.10.1179/000844375795050337 ↗
21. H. Soda, A. McLean, and W.A. Miller: Trans. JIM, 1977, vol. 18, pp. 445–54.10.2320/matertrans1960.18.445 ↗
22. H. Soda, A. McLean, and W.A. Miller: Metall. Trans. B, 1978, vol. 9B, pp. 145–47.10.1007/BF02822684 ↗
23. B.J. Keene, K.C. Mills, A. Kasama, A. McLean, and W.A. Miller: Metall. Trans. B, 1986, vol. 17B, pp. 159–62.10.1007/BF02670828 ↗
24. B. Rayleigh: Proc. R. Soc., 1879, vol. 29, pp. 71–97.
25. H. Chiriac, M. Tomut, C. Naum, F. Necula, and V. Nagacevschi: Mater. Sci. Eng. A, 1997, vols. A226–A228, pp. 341–43.10.1016/S0921-5093(97)80048-2 ↗
26. F.E. Luborsky, P.G. Frischmann, and L.A. Johnson: J. Magn. Magn. Mater., 1980, vol. 19, pp. 130–37.10.1016/0304-8853(80)90573-9 ↗
27. I. Egry, G. Lohofer, P. Neuhaus and S. Sauerland: Mater. Sci. Forum, 1991, vol. 77, pp. 257–68.10.4028/www.scientific.net/MSF.77.257 ↗
28. I. Egry: J. Mater. Sci., 1991, vol. 26, pp. 2997–3003.10.1007/BF01124834 ↗
29. S. Schneider, I. Egry and I. Seyhan: Int. J. Thermophys., 2002, vol. 23 (5), pp. 1241–48.10.1023/A:1019896321431 ↗
30. H-K. Lee, M.G. Frohberg and J. Hajra: Steel Res., 1993, vol. 64 (4), pp. 191–96.10.1002/srin.199301007 ↗
31. D.L. Cummings and D.A. Blackburn: J. Fluid Mech., 1991, vol. 224, pp. 395–416.10.1017/S0022112091001817 ↗
32. A. Kalkanli, J.V. Wood, and N. Braithwaite: Iron Steel Inst. Jpn. Int., 1998, vol. 38 (2) pp. 142–48.10.2355/isijinternational.38.142 ↗
33. T.R. Anthony and H.E. Cline: J. Appl. Phys., 1978, vol. 49 (2), pp. 829–37.10.1063/1.324611 ↗
34. J.J. Hoyt, M. Asta, and A. Karma: Phys. Rev. Lett., 2001, vol. 86, pp. 5530–33.10.1103/PhysRevLett.86.5530 ↗
35. M. Asta, J.J. Hoyt, and A. Karma: Phys. Rev. B, 2002, vol. 66, p. 100101(R).10.1103/PhysRevB.66.100101 ↗
36. J.R. Morris: Phys. Rev. B, 2002, vol. 66, p. 144104.10.1103/PhysRevB.66.144104 ↗
37. J.J. Hoyt and M. Asta: Phys. Rev. B, 2002, vol. 65, p. 214106.10.1103/PhysRevB.65.214106 ↗