Hot plane strain compression testing of aluminum alloys by channel-die compression
Source abstract
Abstract
A thoroughly tested, high-temperature channel-die compression (CDC) rig is described for simulating hot plane strain compression of metallic alloys up to 500 °C. The equipment is currently used to characterize the flow stress and microstructure evolution in hot-rolled Al alloys. It has been validated by several tests involving (1) metallographic analysis of deformed samples; (2) flow stress comparisons with the same, or similar alloys deformed in conventional uniaxial or plane strain compression; and (3) microstructure and texture measurements. The use of modern lubricants enables one to obtain accurate flow stresses and true plane strain deformations that are homogeneous over 80 pct of the sample. The equipment also features rapid heating and cooling systems to minimize thermally-induced microstructure changes. Some results on high-temperature slip systems, hot deformation textures, and microstructures, and the behavior of constituent particles are outlined to illustrate the advantages of the technique.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. J.K. Solberg, H.J. McQueen, N. Ryum, and E. Nes: Phil. Mag. A, 1989, vol. 60, pp. 447–471.10.1080/01418618908213872 ↗
2. M.L. Lovato and M.G. Stout: Metall. Trans. A, 1992, vol. 23A, pp. 935–51.10.1007/BF02675569 ↗
3. B. Kowalski, A.J. Lacey, and C.M. Sellars: Mater. Sci. Technol., 2003, vol. 19, pp. 1564–70.10.1179/026708303225008130 ↗
4. C. Maurice and J.H. Driver: Acta Metall. Mater., 1993, vol. 41, pp. 1653–6410.1016/0956-7151(93)90185-U ↗
5. K.F. Karhausen, J. Savoie, C.M. Allen, D. Piot, and R. Luce: Proc. ICAA8, Mater. Sci. Forum, 2002, vols. 396–402, pp. 371–78.10.4028/www.scientific.net/MSF.396-402.371 ↗
6. G. Guiglionda: Ph.D. Thesis, Ecole des Mines de St-Etienne-INP Grenoble, 2003.
7. F. Perocheau and J.H. Driver: Int. J. Plasticity, 2000, vol. 16, pp. 73–89.10.1016/S0749-6419(99)00048-0 ↗
8. C. Maurice and J.H. Driver: Acta Mater., 1997, vol. 45, pp. 4639–49.10.1016/S1359-6454(97)00117-1 ↗
9. C. Maurice and J.H. Driver: Acta Mater., 1997, vol. 45, pp. 4627–38.10.1016/S1359-6454(97)00115-8 ↗
10. I. Samadjar, P. Ratchev, B. Verlinden, and E. Aernoudt: Acta Mater., 2001, vol. 49, pp. 1759–69.10.1016/S1359-6454(01)00083-0 ↗
11. M. Crumbach and G. Gottstein: Mater. Sci. Eng., 2004, vols. A387–389, pp. 282–87.10.1016/j.msea.2004.01.130 ↗
12. A. Baldacci, A. Bigot, H. Klocker, and J.H. Driver: in Hot Deformation of Aluminum Alloys, Z. Jin, A. Beaudoin, T.A. Bieler, and B. Radhakrishnan, eds., TMS, Warrendale, PA, pp. 509–19.
13. J. Baruchel, J.Y. Buffière, E. Mair, P. Merle and G. Peix: X-Ray Tomography in Material Science, Paris Editions Hermès, Paris, 2000.
14. G. Guiglionda, A. Borbely, and J.H. Driver: Acta Mater., 2004, vol. 52, pp. 3413–23.10.1016/j.actamat.2004.03.037 ↗
15. B. Morere, C. Maurice, R. Shahani, and J.H. Driver: Metall Mater. Trans. A, 2001, vol. 32A, pp. 625–32.10.1007/s11661-001-0079-9 ↗
16. M.-C. Theyssier and J.H. Driver: Mater. Sci. Eng., 1999, vol. A272, pp. 73–82.10.1016/S0921-5093(99)00469-4 ↗
17. J.-C. Glez and J.H. Driver: Acta Mater., 2003, vol. 51, pp. 2989–3003.10.1016/S1359-6454(03)00111-3 ↗
18. H.J. McQueen, W.A. Wong, and J.J. Jonas: Can. J. Phys., 1967, vol. 45, p. 1225.10.1139/p67-091 ↗
19. C. Chovet, C. Desrayaud, and F. Montheillet: Int. J. Mech. Sci., 2002, vol. 44, pp. 343–57.10.1016/S0020-7403(01)00092-3 ↗