journal article·2000-08

An investigation of the effect of fatigue deformation on the residual mechanical properties of Ti-6Al-4V ELI

Toshikazu Akahori, Mitsuo Niinomi, Kei-Ichi Fukunaga

Publisher page

Abstract

Tensile properties, hardness, and Charpy impact toughness of Ti-6Al-4V extralow interstitial (ELI) with equiaxed α and Widmanstatten α structures at various stages of fatigue were investigated. Fatigue crack initiation characteristics of the same alloy were also investigated in this study. In the equiaxed α structure, fatigue cracks initiated mainly at the interface between primary-α grains, while in the Widmanstatten α structure, they initiated across α plates at an angle of around 45 deg to the stress axis. Specimens with the Widmanstatten α structure fractured before adequate fatigue hardening was achieved because a multitude of microcracks readily formed. Specimens with the equiaxed α structure fractured after adequate fatigue hardening developed. Tensile strength, 0.2 pct proof stress, and hardness increased clearly with increasing stress cycles and fatigue steps, particulary in the low-cycle fatigue (LCF) region, while impact toughness and elongation showed a reverse trend. It is suggested, therefore, that the dislocation density multiplies more rapidly near the specimen surface during the early stages of fatigue, while during the later stages of fatigue, dislocation density increases near the center of the specimen. Also, the dislocation multiplication will continue until saturation of the entire specimen has occurred.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Welding Techniques and Residual Stresses · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. R.R. Boyer, G. Welsch, and E.W. Collings: Materials Handbook, Titanium Alloys, ASM, Materials Park, OH, 1994, pp. 483–636.
2. S.R. Seagle: Mater. Sci. Eng. A, 1996, vol. A212, pp. 1–7.10.1016/0921-5093(96)10245-8 ↗
3. R.R. Boyer: Mater. Sci. Eng. A, 1996, vol. A212, pp. 103–14.10.1016/0921-5093(96)10233-1 ↗
4. “Standard Specification for Wrought Titanium 6Al-4V ELI Alloy for Surgical Implant,” [ASTM F136-82,] ASTM, Philadelphia, PA, 1994, pp. 19–20.
5. A. Yamamoto, T. Kobayashi, N. Maruyama, and M. Sumita: J. Biomater., 1996, vol. 14, pp. 158–73.
6. H. Hamanaka and T. Tsutiya: J. Iron Steel Inst. Jpn., 1997, vol. 2, pp. 30–35.
7. Y. Okazaki: J. Jpn. Inst. Met., 1998, vol. 37, pp. 838–42.
8. M. Niimomi: Mater. Sci. Eng. A, 1998, vol. A243, pp. 231–36.10.1016/S0921-5093(97)00806-X ↗
9. D. Kuroda, M. Niinomi, M. Morinaga, Y. Kato, and T. Yashiro: Mater. Sci. Eng. A, 1998, vol. A243, pp. 231–36.
10. M.H. Swain: in Small Crack Test Method, J.M. Larson and J.E. Allison, eds., ASTM, Philadelphia, PA, 1992, pp. 34–56.10.1520/STP15063S ↗
11. T. Kobayashi, I. Yamamoto, and M. Niinomi: J. Testing Eval., 1993, vol. 21, pp. 145–53.10.1520/JTE11763J ↗
12. I.J. Polmear: in Light Alloys, R.W.K. Honeycombe and P. Honcock, eds., Edward Arnold, London, 1998, pp. 248–50.
13. H. Puschrik, J. Fladischer, G. Lütjering, and R.I. Jaffee: Proc. Titanium ’92, F.H. Fores and I.L. Caplan, eds., TMS, Warrendale, PA, 1992, vol. 1, pp. 131–40.
14. K. Minakawa: J. Iron Steel Inst. Jpn., 1989, vol. 75, pp. 36–43.10.2355/tetsutohagane1955.75.7_1104 ↗
15. T. Takemoto, J.K. Jing, T. Tsakarakos, S. Wessman, and I.R. Kramer: Metall. Trans. A, 1983, vol. 14A, pp. 127–32.10.1007/BF02643745 ↗
16. Division of Fatigue and Microstructure Committee of Fatigue: Soc. Mater. Sci. Jpn., 1994, pp. 47–64.
17. T. Akahori, M. Niinomi, and A. Ozeki: J. Jpn. Inst. Met., 1998, vol. 62, pp. 952–60.10.2320/jinstmet1952.62.10_952 ↗
18. E.S. Kayali and A. Plumtree: Metall. Trans. A, 1982, vol. 13A, pp. 1033–41.10.1007/BF02643400 ↗
19. J.C. Grosskerevts and G.G. Shaw: Acta Metall., 1972, vol. 20, pp. 523–28.10.1016/0001-6160(72)90008-9 ↗
20. N.M. Grinberg, A.R. Smirnov, V.A. Moskaienko, L.F. Yakovenko, and V.I. Zmievsky: Mater. Sci. Eng. A, 1993, vol. 165, pp. 125–31.10.1016/0921-5093(93)90746-2 ↗