Large strain work hardening of aluminum alloys and the effect of mg in solid solution
Source abstract
Abstract
The work-hardening behavior of a range of aluminum-magnesium alloys, from 0.5 to 4.55 wt pct Mg, is followed up to large strains using compression testing and cold rolling. At large strains, stage IV, an unexpectedly low work-hardening rate of high-Mg alloys is observed, and the work-hardening rate in stage IV is almost unaffected by the Mg content. A model for work hardening is applied and discussed in relation to the experimental observations. Based on microstructural observations of the cold-rolled materials, the low work-hardening rate of high-Mg alloys is ascribed to a different storage pattern of dislocations caused by an increased amount of shear bands and a higher dislocation density inside subgrains.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. A.D. Rollett and U.F. Kocks: Solid State Phenomena, 1994, vol. 35–36, pp. 1–18.
2. G. Langford and M. Cohen: Trans. Am. Soc. Metall., 1969, vol. 62, pp. 623–38.
3. J.M. Alberdi Garitaonandia: Ph.D. Thesis, University of Navarra, San Sebastian, 1984.
4. M. Zehetbauer and V. Seumer: Acta Metall. Mater., 1993, vol. 41, pp. 577–88.10.1016/0956-7151(93)90088-A ↗
5. J.S. Hayes, R. Keyte, and P.B. Prangnell: Mater. Sci. Technol., 2000, vol. 16, pp. 1259–63.10.1179/026708300101507479 ↗
6. J. Gil Sevillano: in Material Science and Technology. A Comprehensive Treatment, R.W. Cahn (ed.), VCH, Weinheim, 1993, vol. 6, pp. 19–88.
7. O.D. Sherby, R.A. Anderson, and J.E. Dorn: J. Metals, 1951, pp. 643–52.10.1007/BF03397360 ↗
8. U.F. Kocks: J. Eng. Mater. Technol., 1976, vol. 98, pp. 76–85.10.1115/1.3443340 ↗
9. U.F. Kocks and H. Mecking: Prog. Mater. Sci., 2003, vol. 48, pp. 171–73.10.1016/S0079-6425(02)00003-8 ↗
10. P.S. Follansbee and U.F. Kocks: Acta Metall., 1988, vol. 36, pp. 81–93.10.1016/0001-6160(88)90030-2 ↗
11. A.D. Rollett, U.F. Kocks, and R.D. Doherty: in Formability and Metallurgical Structure, A.K. Sachdev and J.D. Embury (eds.), The Metallurgical Society, Orlando, 1987, pp. 211–25.
12. B. Holmedal, K. Martinsen, and E. Nes: in Virtual Fabrication of Aluminum Alloys, J. Hirsch (ed.), John Wiley & Sons, 2006.
13. F.B. Prinz and A.S. Argon: Acta Metall., 1984, vol. 32, pp. 1021–28.10.1016/0001-6160(84)90004-X ↗
14. F. Roters, D. Raabe, and G. Gottstein: Acta Mater., 2000, vol. 48, pp. 4181–89.10.1016/S1359-6454(00)00289-5 ↗
15. M. Zehetbauer: Acta Metall. Mater., 1993, vol. 41, pp. 589–99.10.1016/0956-7151(93)90089-B ↗
16. F.R. Castro-Fernandez, C.M. Sellars, and J.A. Whiteman: Mater. Sci. Technol., 1990, vol. 6, pp. 453–60.10.1179/mst.1990.6.5.453 ↗
17. A.S. Argon and P. Haasen: Acta Metall. Mater., 1993, vol. 41, pp. 3289–306.10.1016/0956-7151(93)90058-Z ↗
18. B. Holmedal, K. Marthinsen, and E. Nes: Z. Metallk., 2005, vol. 96, pp. 532–45.10.3139/146.101067 ↗
19. K. Marthinsen and E. Nes: Mater. Sci. Technol., 2001, vol. 17, pp. 376–88.10.1179/026708301101510096 ↗
20. E. Nes: Prog. Mater. Sci., 1998, vol. 41, pp. 129–94.10.1016/S0079-6425(97)00032-7 ↗
21. E. Nes and K. Marthinsen: Mater. Sci. Eng., 2002, vol. A322, pp. 176–93.10.1016/S0921-5093(01)01130-3 ↗
22. S. Zajac: Swedish Institute for Metals Research, Stockholm, Sweden, unpublished research, 1998.
23. B. Rønning: Hydro Aluminium Sunndal, Sunndalsøra, Norway, unpublished research, 1998.
24. O. Engler: Hydro Aluminium Deutschland, Bonn, Germany, unpublished research, 2002.
25. R.H. Wagoner and J.-L. Chenot: Fundamentals of Metal Forming, John Wiley & Sons, New York, 1996.
26. S. Li and P. Van Houtte: Aluminium, 2002, vol. 78, pp. 918–22.
27. P. Van Houtte: The MTM-FHM Software System Manual, Version 2, Katholieke Universiteit Leuven, Leuven, Belgium, 2000.
28. G.B. Burger, A.K. Gupta, P.W. Jeffrey, and D.J. Lloyd: Mater. Charact., 1995, vol. 35, pp. 23–39.10.1016/1044-5803(95)00065-8 ↗
29. Ø. Ryen, O. Nijs, E. Sjölander, B. Holmedal, H.E. Ebström, and E. Nes: Metall. Trans. A, 2006, vol. 37A, pp. 1999–2006.10.1007/s11661-006-0142-7 ↗
30. V. Randle and O. Engler: Introduction to Texture Analysis: Macrotexture, Microtexture and Orientation Mapping. Gordon and Breach Science, Amsterdam, The Netherlands, 2000.10.1201/9781482287479 ↗
31. M. Koizumi, S. Kohara, and H. Inagaki: Z. Metallk., 2000, vol. 91, pp. 88–96.
32. K. Lücke and O. Engler: Mater. Sci. Technol., 1990, vol. 6, pp. 1113–30.10.1179/mst.1990.6.11.1113 ↗
33. O. Engler, M. Crumbach, and S. Li: Acta Mater., 2005, vol. 53, pp. 2241–57.10.1016/j.actamat.2005.01.032 ↗
34. H. Inagaki and S. Kohara: Z. Metallk., 1997, vol. 88, pp. 570–75.
35. A. Korbel, J.D. Embury, M. Hatherly, P.L. Martin, and H.W. Erbsloh: Acta Metall., 1986, vol. 34, pp. 1999–2009.10.1016/0001-6160(86)90259-2 ↗
36. H.J. Roven and E. Nes: Metall. Sci., 1984, vol. 18, pp. 515–20.10.1016/0036-9748(84)90432-0 ↗
37. S.V. Harren, H.E. Dève, and R.J. Asaro: Acta Metall., 1988, vol. 36, pp. 2435–80.10.1016/0001-6160(88)90193-9 ↗
38. H. Inagaki, M. Koizumi, C.S.T. Chang, and B.J. Duggan: in Aluminium Alloys: Their Physical and Mechanical Properties, P.J. Gregson and S.J. Harris (eds.), Trans Tech Publications, Switzerland, 2002, pp. 587–92.