The effect of small deformation on abnormal grain growth in bulk Cu
Source abstract
Abstract
The effect of small deformation below the level (about 8 pct) required for primary recrystallization on abnormal grain growth (secondary recrystallization) has been investigated in bulk polycrystalline Cu. The starting microstructure, without any texture and with a nearly uniform grain size of 168 µm, has been obtained by compressing a cylindrical Cu specimen and recrystallizing at 800 °C. The fully recrystallized specimen shows distinct abnormal grain growth (AGG) after heat treatment at 800 °C for 12 hours. Most of the grain boundaries are faceted when observed under transmission electron microscopy (TEM), and most of the faceted segments are expected to be singular. A singular grain boundary free of defects will migrate by two-dimensional nucleation of new layers, with its velocity varying nonlinearly with the driving force arising from the grain-size difference. Such a growth mechanism is analogous to the well known process for the growth of crystals with singular surfaces from liquid or vapor. The grains slightly larger than the average size will hardly grow, because the driving force for their growth is not sufficient for nucleation of new crystal layers at the boundaries. Those grains larger than a certain critical size will, however, grow at ever-increasing rates with their increasing size, because of the sufficient driving force for two-dimensional nucleation. Such a selective accelerated growth of large grains results in overall AGG behavior. The specimen deformed to 2 pct shows AGG after heat treatment for only 5 minutes at 800 °C, and after 1 hour, large impinged grains are obtained. The grain boundaries show many extrinsic dislocations even after the heat treatments. As proposed earlier by Gleiter, Balluffi, Smith, and their colleagues, the extrinsic grain-boundary dislocations increase the grain-boundary mobilities even at low driving forces, and, hence, even those grains slightly larger than the average size can rapidly grow at the early stages of the heat treatment, in agreement with the observation. In the specimens deformed to 4 to 8 pct, below the level for primary recrystallization, all grains grow steadily without producing distinct AGG. With high densities of extrinsic dislocations at the grain boundaries even after long heat treatments, all grains can readily grow, resulting in overall growth patterns resembling the normal growth. When deformed to 20 and 50 pct, primary recrystallization occurs, and the subsequent AGG behavior depends on the grain size obtained at the completion of the primary recrystallization. Similar small-deformation effects are observed with heat treatment at 600 °C.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (76)
Show source-provided references
1. C. Antonione, G.D. Gatta, G. Riontino, and G. Venturello: J. Mater. Sci., 1973, vol. 8, pp. 1–10.10.1007/BF00755577 ↗
2. C. Antonione, F. Marino, G. Riontino, and M.C. Tabasso: J. Mater. Sci., 1977, vol. 12, pp. 747–50.10.1007/BF00548166 ↗
3. G. Riontino, C. Antonione, L. Battezzati, F. Marino, and M.C. Tabasso: J. Mater. Sci., 1979, vol. 14, pp. 86–90.10.1007/BF01028331 ↗
4. V. Randle and A. Brown: Phil. Mag. A, 1988, vol. 58, pp. 717–36.10.1080/01418618808209949 ↗
5. K.T. Aust: The Art and Science of Growing Crystals, J.J. Gilman, ed., Wiley, New York, NY, 1963, pp. 452–78.
6. S.B. Lee, N.M. Hwang, D.Y. Yoon, and M.F. Henry: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 985–94.10.1007/s11661-000-0040-3 ↗
7. J.B. Koo and D.Y. Yoon: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 469–75.10.1007/s11661-001-0063-4 ↗
8. J.B. Koo and D.Y. Yoon: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1911–26.10.1007/s11661-001-0004-2 ↗
9. S.B. Lee, D.Y. Yoon, and M.F. Henry: Acta Mater., 2000, vol. 48, pp. 3071–80.10.1016/S1359-6454(00)00119-1 ↗
10. J.S. Choi and D.Y. Yoon: Iron Steel Inst. Jpn. Int., 2001, vol. 41, pp. 478–83.10.2355/isijinternational.41.478 ↗
11. C.G. Dunn and J.L. Walter: in Recrystallization, Grain Growth and Textures, H. Margolin, ed., ASM, Metals Park, OH, 1966, pp. 461–521.
12. F.J. Humphreys and M. Hartherly: Recrystallization and Related Annealing Phenomena, Pergamon, Oxford, United Kingdom, 1995, pp. 281–325.
13. M. Hillert: Acta Metall., 1965, vol. 13, pp. 227–38.10.1016/0001-6160(65)90200-2 ↗
14. T. Gladman: JOM, 1992, vol. 44, pp. 21–24.10.1007/BF03222321 ↗
15. C.H. Wörner and P.M. Hazzledine: JOM, 1992, vol. 44, pp. 16–20.10.1007/BF03222320 ↗
16. M. Ferry and F.J. Humphreys: Acta Mater., 1996, vol. 44, pp. 1293–1308.10.1016/1359-6454(95)00316-9 ↗
17. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 4231–40.10.1016/S1359-6454(97)00070-0 ↗
18. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 5031–39.10.1016/S1359-6454(97)00173-0 ↗
19. A.D. Rollett, D.J. Srolovitz, and M.P. Anderson: Acta Metall., 1989, vol. 37, pp. 1227–40.10.1016/0001-6160(89)90117-X ↗
20. C.V. Thompson, H.J. Frost, and F. Spaepen: Acta Metall., 1987, vol. 35, pp. 887–90.10.1016/0001-6160(87)90166-0 ↗
21. D.J. Srolovitz, G.S. Grest, and M.P. Anderson: Acta Metall., 1985, vol. 33, pp. 2233–47.10.1016/0001-6160(85)90185-3 ↗
22. S.H. Lee, J.S. Choi, and D.Y. Yoon: Z. Metallkd., 2001, vol. 92, pp. 655–62.
23. C.W. Park and D.Y. Yoon: J. Am. Ceram. Soc., 2000, vol. 83, pp. 2605–609.10.1111/j.1151-2916.2000.tb01161.x ↗
24. B.K. Lee, S.Y. Chung, and S.J.L. Kang: Acta Mater., 2000, vol. 48, pp. 1575–80.10.1016/S1359-6454(99)00434-6 ↗
25. G. Henry, J. Plateau, X. Waché, M. Gerber, I. Behar, and C. Crussard: Mém. Sci. Rev. Métall., 1959, vol. 56, pp. 417–26.
26. J.R. Rellick, C.J. McMahon, H.L. Marcus, and P.W. Palmberg: Metall. Trans., 1971, vol. 2, pp. 1492–94.10.1007/BF02913388 ↗
27. T.G. Ference and R.W. Balluffi: Scripta Metall., 1988, vol. 22, pp. 1929–34.10.1016/S0036-9748(88)80240-0 ↗
28. T.E. Hsieh and R.W. Balluffi: Acta Metall., 1989, vol. 37, pp. 2133–39.10.1016/0001-6160(89)90138-7 ↗
29. K.J. Morrissey and C.B. Carter: J. Am. Ceram. Soc., 1984, vol. 67, pp. 292–301.10.1111/j.1151-2916.1984.tb19521.x ↗
30. M.A. Gülgün, V. Putlayev, and M. Rühle: J. Am. Ceram. Soc., 1999, vol. 82, pp. 1849–56.10.1111/j.1151-2916.1999.tb02008.x ↗
31. T. Yamamoto, Y. Ikuhara, K. Hayashi, and T. Sakuma: J. Mater. Res., 1998, vol. 13, pp. 3449–52.10.1557/JMR.1998.0469 ↗
32. C. Herring: Phys. Rev., 1951, vol. 82, pp. 87–93.10.1103/PhysRev.82.87 ↗
33. F.C. Frank: in Metal Surfaces, W.D. Robertson and N.A. Gjostein, eds., ASM, Metals Park, OH, 1963, pp. 1–15.
34. J.W. Cahn: J. Phys. Colloq. 6, 1982, No. 12, pp. 199–213.10.1007/BF00726849 ↗
35. H. Gleiter: Acta Metall., 1969, vol. 17, pp. 565–73.10.1016/0001-6160(69)90115-1 ↗
36. H. Gleiter: Acta Metall., 1969, vol. 17, pp. 853–62.10.1016/0001-6160(69)90105-9 ↗
37. H. Gleiter: Acta Metall., 1969, vol. 17, pp. 1421–28.10.1016/0001-6160(69)90004-2 ↗
38. S.E. Babcock and R.W. Balluffi: Acta Metall., 1989, vol. 37, pp. 2357–65.10.1016/0001-6160(89)90033-3 ↗
39. S.E. Babcock and R.W. Balluffi: Acta Metall., 1989, vol. 37, pp. 2367–76.10.1016/0001-6160(89)90034-5 ↗
40. C.M.F. Rae and D.A. Smith: Phil. Mag. A, 1980, vol. 41, pp. 477–92.10.1080/01418618008239327 ↗
41. K.L. Merkle and L.J. Thompson: Mater. Lett., 2001, vol. 48, pp. 188–93.10.1016/S0167-577X(00)00301-3 ↗
42. W.K. Burton, N. Cabrera, and F.C. Frank: Phil. Trans. R. Soc., London, Sect. A, 1951, vol. A243, pp. 299–358.
43. P.E. Wolf, F. Gallet, S. Balibar, E. Rolley, and P. Nozières: J. Phys., 1985, vol. 46, pp. 1987–2007.10.1051/jphys:0198500460110198700 ↗
44. S.D. Peteves and R. Abbaschian: Metall. Trans. A, 1991, vol. 22A, pp. 1259–70.10.1007/BF02660658 ↗
45. F.C. Frank: J. Cryst. Growth, 1981, vol. 51, pp. 367–68.10.1016/0022-0248(81)90322-5 ↗
46. J.D. Weeks and G.H. Gilmer: in Advances in Chemical Physics, Vol. XL, I. Prigogine and S.A. Rice, eds., Wiley, New York, NY, 1979, pp. 157–227.10.1002/9780470142592.ch4 ↗
47. G.H. Gilmer: J. Cryst. Growth, 1977, vol. 42, pp. 3–10.10.1016/0022-0248(77)90170-1 ↗
48. Y.J. Park, N.M. Hwang, and D.Y. Yoon: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2809–19.10.1007/BF02652373 ↗
49. R. Warren: J. Less-Common Met., 1969, vol. 17, pp. 65–72.10.1016/0022-5088(69)90037-X ↗
50. R. Warren: J. Mater. Sci., 1968, vol. 3, pp. 471–85.10.1007/BF00549730 ↗
51. C.W. Park and D.Y. Yoon: J. Am. Ceram. Soc., 2002, vol. 85, pp. 1585–93.10.1111/j.1151-2916.2002.tb00492.x ↗
52. C.A. Bateman, S.J. Bannison, and M.P. Harmer: J. Am. Ceram. Soc., 1989, vol. 72, pp. 1241–44.10.1111/j.1151-2916.1989.tb09715.x ↗
53. Y.S. Yoo, H. Kim, and D.Y. Kim: J. Eur. Ceram. Soc., 1997, vol. 17, pp. 805–11.10.1016/S0955-2219(96)00134-3 ↗
54. P. Wynblatt and N.A. Gjostein: Acta Metall., 1976, vol. 24, pp. 1165–74.10.1016/0001-6160(76)90034-1 ↗
55. P. Wynblatt: Acta Metall., 1976, vol. 24, pp. 1175–82.10.1016/0001-6160(76)90035-3 ↗
56. D.Y. Yoon, C.W. Park, and J.B. Koo: Proc. Int. Workshop on Ceramic Interfaces: Properties and Application IV (Ceramic Interfaces 2), H.I. Yoo and S.J.L. Kang, eds., The Institute of Materials, London, 2001, pp. 3–21.
57. H. van Beijeren and I. Nolden: in Structure and Dynamics of Surface II: Phenomena, Models, and Methods, W. Schommers and P. von Blanckenhagen, eds., Springer-Verlag, Berlin, 1987, pp. 259–300.10.1007/978-3-642-46591-8_7 ↗
58. J.D. Weeks: in Ordering in Strongly Fluctuating Condensed Matter Systems, T. Riste, ed., Plenum, New York, NY, 1980, pp. 293–317.10.1007/978-1-4684-3626-6_21 ↗
59. M. Wortis: Chemistry and Physics of Solid Surfaces VII, R. Vanselow and R.F. Howe, eds., Springer-Verlag, Berlin, 1988, pp. 367–405.10.1007/978-3-642-73902-6_13 ↗
60. E.H. Conrad: Progr. Surf. Sci., 1992, vol. 39, vol. 65–166.10.1016/0079-6816(92)90006-4 ↗
61. H.J. Leamy, G.H. Gilmer, and K.A. Jackson: Surface Physics of Materials, Vol. 1, J.M. Blakely, ed., Academic Press, New York, NY, 1975, pp. 121–88.10.1016/B978-0-12-103801-4.50009-4 ↗
62. C. Rottman: Phys. Rev. Lett., 1986, vol. 57, pp. 735–38.10.1103/PhysRevLett.57.735 ↗
63. J.P. Hirth and G.M. Pound: in Condensation and Evaporation, Nucleation and Growth Kinetics, Progress in Materials Science, Vol. II, B. Chalmers, ed., Pergamon Press, Oxford, United Kingdom, 1963, pp. 77–148.
64. I.M. Lifshitz and V.V. Slyozov: J. Phys. Chem. Solids, 1961, vol. 19, pp. 35–50.10.1016/0022-3697(61)90054-3 ↗
65. S.S. Kim and D.N. Yoon: Acta Metall., 1983, vol. 31, pp. 1151–57.10.1016/0001-6160(83)90177-3 ↗
66. J.B. Koo, D.Y. Yoon, and M.F. Henry: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1489–91.10.1007/s11661-000-0267-z ↗
67. C.W. Park: Ph.D. Thesis, Korea Advanced Institute of Science and Technology, Taejon, Korea, 2000.
68. S.B. Lee, S.Y. Choi, S.J.L. Kang, and D.Y. Yoon: Acta Mater., submitted for publication.
69. W.V. Saarloos and G.H. Gilmer: Phys. Rev., 1986, vol. 33B, pp. 4927–35.10.1103/PhysRevB.33.4927 ↗
70. E. van Veenendaal, P.J.C.M. van Hoof, J. van Suchtelen, W.J.P. van Enckevort, and P. Bennema: Surf. Sci., 1998, vol. 417, pp. 121–38.10.1016/S0039-6028(98)00676-1 ↗
71. L.J.P. Vogels, H.A.M. Marsman, M.A. Verheijen, P. Bennema, and M. Elwenspoek: J. Cryst. Growth, 1990, vol. 100, pp. 439–46.10.1016/0022-0248(90)90242-D ↗
72. J.B. Koo: PhD. Thesis, Korea Advanced Institute of Science and Technology, Taejon, Korea, 2000.
73. T.L. Lin and D. McLean: Met. Sci. J., 1968, vol. 2, pp. 108–13.10.1179/030634568790443413 ↗
74. P.H. Pumphrey and H. Gleiter: Phil. Mag., 1974, vol. 30, pp. 593–602.10.1080/14786439808206584 ↗
75. R.Z. Valiev, V. Yu, Gertsman, and O.A. Kaibyshev: Phys. Status Solidi (a), 1986, vol. 97, pp. 11–56.10.1002/pssa.2210970102 ↗
76. R.Z. Valiev, V. Yu, Gertsman, and O.A. Kaibyshev: Scripta Metall., 1983, vol. 17, pp. 853–56.10.1016/0036-9748(83)90248-X ↗