journal article·2006-05

Rheological behavior of Al-Mg-Si-Cu alloys in the mushy state obtained by partial remelting and partial solidification at high cooling rate

D. Fabrègue, A. Deschamps, M. Suéry, W. J. Poole

Publisher page

Abstract

This work investigates the mechanical behavior of two aluminum alloys in the mushy state, the alloy AA6056 and an alloy based on mixing AA6056 and AA4047. These alloys have been studied to give insight into the susceptibility to hot tearing, which occurs during laser welding of AA6056 with 4047 filler wire. Two types of isothermal tensile tests have been conducted: (1) tests during partial remelting and (2) tests after partial solidification at a high cooling rate. Results show that the maximum tensile stress increases with increasing solid volume fraction. Both materials exhibit visco-plastic behavior for solid fractions in the range 0.9 to 0.99, except for a critical solid fraction of 0.97, where the semisolid material also shows minimum ductility. The stress levels observed for the remelting experiments are larger than those found for partial solidification experiments at the same solid fraction due to the influence of the microstructure. The influence of temperature and strain rate on the maximum stress is described by using a constitutive law that takes into account the fraction of grain boundaries wetted by the liquid.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. H. Yamaoka, M. Yuki, T. Murayama, K. Tsuchita, and T. Irisawa: Welding Int., 1992, vol. 6 (10), pp. 766–73.10.1080/09507119209548283 ↗
2. R. Dif, D. Bechet, T. Warner, and H. Ribes: Materials Science Forum, Proc. 6th Int. Conf. on Aluminium Alloys, T. Sato, S. Kumai, and T. Kobayashi, The Japan Institute of Light Metals, Toyohashi, Japan, 1998, pp. 1991–96.
3. H. Sakamoto, K. Shibata, and F. Dausinger: Proc. 4th Eur. Conf. on Laser Treatments of Materials, B.L. Mordike, ed., 1992, pp. 523–28.10.2351/1.5058523 ↗
4. C. Liu, D.O. Northwood, and S.D. Bhole: Mater. Des., 2004, vol. 25, pp. 573–77.10.1016/j.matdes.2004.02.017 ↗
5. D. Fabrègue and A. Deschamps: Materials Science Forum, Proc. 8th Int. Conf. on Aluminium Alloys, P.J. Gregson and S. Harris, eds., Trans Tech Publications, Aedermannsdorf, Switzerland, 2002, vols. 396–402, pp. 1567–72.
6. M. Quian and J.C. Lippold: Welding J., 2003, June, pp. 145–50.
7. J.C. Ion: Sci. Technol. Welding Joining, 2001, vol. 5 (5), pp. 265–76.10.1179/136217100101538308 ↗
8. X. Tiang and Q. Shi: J. Mater. Processing Technol., 2000, vol. 97, pp. 30–34.10.1016/S0924-0136(99)00093-X ↗
9. N. Kerrouault: Ph.D. Thesis, CEA, Saclay, France, 2001.
10. W. Wu and C.H. Tsai: Metall. Mater. Trans. A, 1999, vol. 30, pp. 417–26.10.1007/s11661-999-0154-1 ↗
11. V. Shankar, T.P.S. Gill, A.L.E. Terrance, S.L. Mannan, and S. Sundaresan: Metall. Mater. Trans. A, (2000), vol. 31, pp. 3109–22.10.1007/s11661-000-0090-6 ↗
12. J. Rapp, C. Glumann, F. Dausinger, and H. Hugel: Proc. 5th Int. Conf. on Welding and Melting by Electron and Laser Beams, P. Denney, I. Miyamoto, and B.L. Mordike, eds., Commissariat à l’énergie, atomique, France, 1993, p. 672.
13. O. Ludwig: Ph.D. Thesis, INPG, Grenoble, France, 2004.
14. D. Warrington and D.G. McCartney: Cast Met., 1989, vol. 2 (3), pp. 134–43.10.1080/09534962.1989.11818994 ↗
15. M. Suéry, C.L. Martin, M. Braccini, and Y. Brechet: Adv. Eng. Mater., 2001, vol. 3 (8), pp. 589–93.10.1002/1527-2648(200108)3:8<589::AID-ADEM589>3.0.CO;2-N ↗
16. M. Rappaz, J.M. Drezet, and M. Gremaud: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 449–56.10.1007/s11661-999-0334-z ↗
17. D.G. Eskin, Suyitno, and L. Katgerman: Progr. Mater. Sci., 2004, vol. 49 (5), pp. 629–711.10.1016/S0079-6425(03)00037-9 ↗
18. M.G. Chu and D.A. Granger: Materials Science Forum, Proc. 5th Int. Conf. on Aluminium Alloys, J.H. Driver, B. Dubost, F. Durand, R. Fougeres, P. Guyot, P. Sainfort, and M. Suery, eds., Trans Tech Publications, Aedermannsdorf, Switzerland, 1996, vols. 217–222, pp. 1505–10.10.4028/www.scientific.net/MSF.217-222.1505 ↗
19. J.A. Spittle, S.G.R. Brown, J.D. James, and R.W. Evans: Proc. 9th Symp. on Physical Simulation of Casting, Hot Rolling and Welding, Suzaki, Sakai, and Matsuda, eds., 1996, pp. 81–91.
20. C.L. Martin, D. Favier, and M. Suéry: Int. J. Plast., 1999, vol. 15, pp. 981–1008.10.1016/S0749-6419(99)00017-0 ↗
21. P. Ackermann, W. Kurz, and W. Heinemann: Mater. Sci. Eng., A, 1985, vol. 75, pp. 79–86.10.1016/0025-5416(85)90179-X ↗
22. B. Magnin, L. Maenner, L. Katgerman, and S. Engler: Materials Science Forum, Proc. 5th Int. Conf. on Aluminium Alloys, J.H. Driver, B. Dubost, F. Durand, R. Fougeres, P. Guyot, P. Sainfort, and M. Suéry, eds., Trans Tech Publications, Aedermannsdorf, Switzerland, 1996, vols. 217–222, pp. 1209–14.10.4028/www.scientific.net/MSF.217-222.1209 ↗
23. C. Sigli, L. Maenner, C. Sztur, and R. Shahani: Materials Science Forum, Proc. 6th Int. Conf. on Aluminium Alloys, T. Sato, S. Kumai, T. Kobayashi, and Y. Murakami, The Japan Institute of Light Metals, Toyohashi, Japan, 1998.
24. D. Fabrègue, A. Deschamps, and M. Suéry: Materials Science Forum, Proc. 9th Int. Conf. on Aluminium Alloys, J.F. Nie, A.J. Morton, and B.C. Muddle, eds., Institute of Materials Engineering Australasia Ltd., Brisbane, Australia 2004, vol. 28, pp. 165–71.
25. S. Instone, D. St. John, and J. Grandfield: Int. J. Cast Met. Res., 2000, vol. 12, pp. 441–56.10.1080/13640461.2000.11819381 ↗
26. C. Darcourt: Université Technologique de Compiègne (UTC), Roberval Laboratory, private communication, 2003.
27. W.M. Van Haaften, W.H. Kool, and L. Katgerman: Mater. Sci. Eng., A, 2002, vol. 336, pp. 1–6.10.1016/S0921-5093(01)01987-6 ↗
28. J.-M. Drezet and G. Eggeler: Scripta Mater., 1994, vol. 31 (6), pp. 757–62.10.1016/0956-716X(94)90223-2 ↗
29. P.J. Wray: Acta Metall., 1975, vol. 24, pp. 125–33.10.1016/0001-6160(76)90015-8 ↗
30. J.P. Poirier: Plasticité à Haute Temperature des Solides Cristallins, Eyrolles, Paris, France, 1976.
31. A.K. Dahle, S. Instone, and T. Sumitomo: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 105–13.10.1007/s11661-003-0212-z ↗
32. D. Fabrègue: Ph.D. Thesis, Institut National Polytechnique de Grenoble, Grenoble, France, 2004.
33. M. Rappaz: EPFL, Lausanne, Switzerland, private communication, 2004.