journal article·2000-05

Dynamic bake hardening of interstitial-free steels

K. Dehghani, J. J. Jonas

Publisher page

Abstract

Two types of dynamic strain aging (DSA) strengthening methods were investigated to determine their potentials for industrial use. They are referred to here as dynamic-static bake hardening (DSBH) and dynamic bake hardening (DBH). For this purpose, a 0.06 pct Ti interstitial-free (IF) steel was reheated to 900 °C and cooled at 12 °C/s to room temperature. It was then dynamically bake hardened in the temperature range 100 °C to 250 °C to strains of 2 to 8 pct at a strain rate of 10−3 s−1. The tensile properties were determined before and after these treatments. It was found that the occurrence of DSA during dynamic baking led to significant increases in work-hardening rate as well as in the final strength. The results indicate that, for a given solute carbon level, the dynamically and then statically aged samples have higher strengths than those that are bake hardened in the conventional way.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. W.C. Jeong: Metall. Mater. Trans. A, 1998, vol. 29, pp. 463–67.10.1007/s11661-998-0126-x ↗
2. A. Itami, K. Ushioda, N. Kimura, H. Asano, Y. Kimura, and K. Koyama: Nippon Steel Technical Report No. 64, Nippon Steel, Kimitsu, Japan, 1995, Iron and Steel Society of AIME, Warrendale, PA, pp. 26–32.
3. Y. Tokunaga and H. Kato: Proc. Symp. on Metallurgy of Vacuum-Degassed Steel Products, TMS, Warrendale, PA, 1989, pp. 91–108.
4. J.M. Rubianes and P. Zimmer: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 111–17.
5. C.-S. Lee and B.K. Zuidema: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 103–10.
6. F.D. Bailey, R.P. Foley, and D.K. Matlock: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 119–33.
7. W. Bleck, R. Bode, O. Maid, and L. Meyer: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 141–48.
8. A. Van Snick, D. Vanderschueren, S. Vandeputte, and J. Dilewijns: Proc. of 39th MWSP Conf., Indianapolis, IN, 1997, pp. 225–32.
9. S. Satoh, S. Okada, T. Kato, O. Hashimoto, T. Hanazawa, and H. Tsunekawa: Kawasaki Steel Technical Report No. 27, Kawasaki Steel, Chiba, Japan, 1992, pp. 31–38.
10. K. Sakata, S. Satoh, T. Kato, and O. Hashimoto: Proc. Int. Forum Phys. Metall. of IF Steels, ISIJ, Tokyo, 1994, pp. 279–88.
11. S.R. Lynes and I.P. O’Reilly: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 79–88.
12. F. Rana, R. Skolly, and I. Gupta: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, AIME, New York, NY, 1994, pp. 89–102.
13. T. Irie, S. Satoh, A. Yasuda, and O. Hashimoto: Proc. Symp. on Metallurgy of Continuous-Annealed Sheet Steel, Dallas, TX, 1982, TMS-AIME, Warrendale, PA, 1982, pp. 155–71.
14. T. Hayashida, M. Oda, T. Yamada, Y. Matsukawa, and J. Tanaka: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994 ISS, Warrendale, PA, 1994, pp. 135–39.
15. K. Dehghani and J.J. Jonas: Proc. 39th MWSP Conf., Indianapolis, IN, Iron and Steel Society of AIME, Warrendale, PA, 1997, pp. 205–12.
16. K. Dehghani, T. Maccagno, and J.J. Jonas: Proc. Int. Conf. on Thermomechanical Processing of Steels and Other Materials, THERMEC ’97, Wollongong, Australia, 1997, TMS, Warrendale, PA, 1997, pp. 891–97.
17. K. Dehghani, T. Maccagno, and J.J. Jonas: Proc. 38th MWSP Conf., Cleveland, OH, Iron and Steel Society of AIME, Warrendale, PA, 1996, pp. 399–407.
18. ASTM Standard E 8M, Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 1990, vol. 01.02, pp. 598–612.
19. A. Karimi Taheri, T.M. Maccagno, and J.J. Jonas: Iron Steel Inst. Jpn. Int. 1995, vol. 35, pp. 1532–40.10.2355/isijinternational.35.1532 ↗
20. K. Ushioda, N. Yoshinaga, K. Koyama, and O. Akisue: Proc. Int. Forum on Physical Metallurgy of IF Steels, ISIJ, Tokyo, 1994, pp. 227–44.
21. X. Yang, D. Vanderschueren, J. Dilewijns, C. Standaert, and Y. Houbaert: Iron Steel Inst. Jpn. Int., 1996, vol. 36, pp. 1286–94.10.2355/isijinternational.36.1286 ↗
22. J. Chipman: Metall. Trans., 1972, vol. 3, pp. 55–64; Metals Handbook, 8th ed., ASM, Metals Park, OH, 1973, vol. 8.10.1007/BF02680585 ↗
23. C.A. Wert: Trans. AIME, 1950, vol. 188, pp. 1242–44.
24. J.D. Fast: Interaction of Metals and Gases, Academic Press, New York, NY, 1965.
25. R.P. Foley, M.E. Fine, and S.K. Bhat: Proc. 39th MWSP Conf., Indianapolis, IN, Iron and Steel Society of AIME, Warrendale, PA, 1997, pp. 653–66.
26. A.J. Boucek and J.F. Butler: Proc. Symp. on Hot- and Cold-Rolled Sheet Steel, Cincinnati, OH, 1987, TMS, Warrendale, PA, 1987, pp. 177–95.
27. M.L. Weaver, R.D. Noebe, J.J. Lewandowski, B.F. Oliver, and M.J. Kaufman: Intermetallics, 1996, vol. 4, pp. 533–42.10.1016/0966-9795(96)00040-4 ↗
28. J.-O. Sperle and K. Olsson: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, AIME, Baltimore, MD, 1994, pp. 65–78.
29. J.M. Rubianes and P. Zimmer: Rev. Metall., 1996, vol. 93, pp. 99–101.10.1051/metal/199693010099 ↗
30. P. Elsen and H.P. Hougardy: Steel Res., 1993, vol. 64, pp. 431–36.10.1002/srin.199301049 ↗
31. M. Kurosawa, S. Satoh, T. Obara, and K. Tsunoyama: Kawasaki Steel Technical Report No. 18, Kawasaki Steel, Chiba, Japan, 1988, pp. 61–65.
32. C.C. Li and W.C. Leslie: Metall. Trans. A, 1978, vol. 9A, pp. 1765–75.
33. C.C. Li, A. Yaker, and W.C. Leslie: Proc. 4th Int. Conf. on the Strength of Metals and Alloys, Nancy, France, Pergamon Press, Oxford, UK, 1976, vol. 2, pp. 731–35.
34. E.T. Stephenson and M. Cohen: Trans. ASM, 1961, vol. 54, pp. 72–83.
35. A.H. Cottrell and G.M. Leak: J. Iron Steel Inst., 1952, vol. 172, pp. 301–06.
36. D.V. Wilson: Acta Metall., 1957, vol. 5, pp. 293–302.10.1016/0001-6160(57)90041-X ↗
37. D.V. Wilson and B. Russell: Acta Metall., 1960, vol. 8, pp. 36–45.10.1016/0001-6160(60)90138-3 ↗
38. D.V. Wilson and B. Russell: Acta Metall., 1960, vol. 8, pp. 468–79.10.1016/0001-6160(60)90033-X ↗
39. Z. Simanovic, U.J. Brand, M. Ichikawa, and S.V. Subramanian: Proc. Int. Conf. on Thermomechanical Processing of Steels and Other Materials, THERMEC ’97, Wollongong, Australia, 1997, TMS, Warrendale, PA, 1997, pp. 419–25.
40. E. Kozeschink and B. Buchmayr: Steel Res., 1997, vol. 68, pp. 224–30.10.1002/srin.199701783 ↗
41. K. Dehghani: Ph.D. Thesis, McGill University, Montreal, Mar. 1999.
42. H. Takechi: Proc. Symp. on Hot- and Cold-Rolled Sheet Steel, Cincinnati, OH, 1987, TMS, Warrendale, PA, pp. 117–38.
43. C. Brun, P. Patou, and P. Parniere: Proc. Symp. on Metallurgy of Continuous Annealed Sheet Steel, Dallas, TX, 1982, TMS-AIME, Warrendale, PA, 1982, pp. 173–97.
44. A. Lankila and A. Ranta-Eskola: Proc. Symp. on Developments in the Annealing of Sheet Steels, Cincinnati, OH, 1992, TMS, Warrendale, PA, pp. 151–58.
45. F. Bugnard, D. Rault, and M. Entringer: Proc. Symp. on Hot- and Cold-Rolled Sheet Steel, Cincinnati, OH, 1987, TMS, Warrendale, PA, 1987, pp. 165–76.
46. J. Dilewijns, D. Vanderschueren, M. Baetens, K. Mols, and S. Claessens: Proc. Int. Conf. on Thermomechanical Processing of Steels and Other Materials, THERMEC ’97, Wollongong, Australia, 1997, TMS, Warrendale, PA, 1997, pp. 467–73.
47. S. Lou and D.O. Northwood: Can. Metall. Q., 1994, vol. 33, pp. 243–249.10.1179/cmq.1994.33.3.243 ↗
48. S. Lou and D.O. Northwood: J. Mater. Eng. Performance, 1994, vol. 3, pp. 344–49.10.1007/BF02645330 ↗
49. S. Lou and D.O. Northwood: Can. Metall. Q., 1992, vol. 31, pp. 225–29.10.1179/cmq.1992.31.3.225 ↗
50. K. Sugimoto and M. Kobayashi: Proc. Symp. on High-Strength Sheet Steels for the Automotive Industry, Baltimore, MD, 1994, ISS, Warrendale, PA, 1994, pp. 255–65.