Analysis of Microstructural Evolution in Alloy 718 Nickel-Based Superalloy During Long-Term Annealing at 760 °C
Source abstract
Abstract
Abstract Alloy 718 (UNS N077718) is commonly used in the aerospace industry, particularly in aircraft engines. In this study, a test piece made of Alloy 718 with the chemical composition Ni19Cr18.5Fe3Mo0.9Ti0.6Al0.04C (wt pct) was subjected to annealing at 760 °C for durations up to 1000 hours. The observed microstructural changes were compared with numerical simulations based on the CALPHAD methodology. Increasing the annealing time at 760 °C leads to an enlargement of the γ″ phase, which consists of disk-shaped precipitates, and their subsequent dissolution into the γ matrix. The matrix becomes enriched in niobium; as a result, the δ phase, coherent with the matrix, precipitates. This phase exhibits a plate-like morphology. An annealing leads to significant degradation of the microstructure. After 1000 hours, the hardness decreased from the initial state of 479 to 345 HV0.5. CALPHAD simulations are valuable input, but the precipitation simulation model underestimates the amount of γ′ and incorrectly predicts the presence of γ″. A comparison of microstructural examinations with CALPHAD simulations indicates that 1000 hours at 760 °C is insufficient to achieve thermodynamic equilibrium. The volume fraction of phases after annealing at 760 °C was determined on 3D reconstructed volumes obtained using FIB-SEM tomography methods. A γ″ volume fraction was 12.8 pct with a mean equivalent diameter = 15 nm after 50 hours, and the volume fraction increased to 13.5 pct after 250 hours. After 250, the volume fraction of δ phase was 11.6 pct. Spheroidal γ′ precipitates with a mean diameter = 53.4 nm were found in places where γ″ dissolved. Longer annealing times, up to 1000 hours resulted in the replacement of γ″ phase by spheroidal γ′ phase precipitates. Transmission Electron Microscopy methods enabled the identification of phases and the determination of crystallographic orientation between phases present in the alloy’s microstructure. HRSTEM measurements indicate that the γ phase creates a local compressive stress field in the matrix perpendicular to the γ/γ″ interface, specifically along the (002) γ matrix plane. Analysis of the deformation field around the γ″ phase precipitate resulting from lattice mismatch reveals its anisotropic nature. The stress level generated by precipitates was estimated using the Eshelby theory for elastic disk-shaped inclusions. The normal stress components in the matrix are as follows: σ 11 = 7.882 GPa, σ 22 = 7.882 GPa, σ 33 = 13.306 GPa. The maximum stress develops along the direction normal to the γ/γ″ interface, restricting plate growth in this direction (i.e., along the plate thickness). In contrast, growth in the two orthogonal directions is thermodynamically favorable, leading to the formation of disk-shaped precipitates.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Additive Manufacturing Materials and Processes · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (94)
Show source-provided references
1. R.C. Reed: The superalloys: fundamentals and applications—Roger C. Reed—Google Books, Cambridge University Press, Cambridge, 2006, p. 372.10.1017/CBO9780511541285 ↗
2. Robert E. Schafrik, D.D.W.J.R.G. Application of Alloy 718 in GE Aircraft Engines: Past, Present and Next Five Years . Superalloy 718, 625, 706 and Various Derivatives 2001.10.7449/2001/Superalloys_2001_1_11 ↗
3. Paulonis D. F., S.J.J. Alloy 718 at Pratt & Whitney – Historical Perspective and Future Challenges. Journal/Academic Society: TMS (The Minerals, Metals & Materials Society) 2001.10.7449/2001/Superalloys_2001_13_23 ↗
4. A. Kruk, S. Lech, A. Gil, G. Cempura, A. Agüero, A.M. Wusatowska-Sarnek, and A. Czyrska-Filemonowicz: Three-dimensional characterization of an oxide scale on ATI 718Plus® Superalloy. Corros. Sci., 2020, vol. 169, 108634https://doi.org/10.1016/j.corsci.2020.108634.10.1016/j.corsci.2020.108634 ↗
5. Kh.A. Al-hatab, M.A. Al-bukhaiti, U. Krupp, and M. Kantehm: Cyclic oxidation behavior of IN 718 superalloy in air at high temperatures. Oxid. Met., 2011, vol. 75, pp. 209–28. https://doi.org/10.1007/s11085-010-9230-6.10.1007/s11085-010-9230-6 ↗
6. C. Juillet, A. Oudriss, J. Balmain, X. Feaugas, and F. Pedraza: Characterization and oxidation resistance of additive manufactured and forged IN718 Ni-based superalloys. Corros. Sci., 2018, vol. 142, pp. 266–76. https://doi.org/10.1016/j.corsci.2018.07.032.10.1016/j.corsci.2018.07.032 ↗
7. Y. Han and M.C. Chaturvedi: Steady state creep deformation of superalloy inconel 718. Mater. Sci. Eng., 1987, vol. 89, pp. 25–33. https://doi.org/10.1016/0025-5416(87)90246-1.10.1016/0025-5416(87)90246-1 ↗
8. Z. Xu, C.J. Hyde, C. Tuck, and A.T. Clare: Creep behaviour of inconel 718 processed by laser powder bed fusion. J. Mater. Process. Technol., 2018, vol. 256, pp. 13–24. https://doi.org/10.1016/j.jmatprotec.2018.01.040.10.1016/j.jmatprotec.2018.01.040 ↗
9. W. Chen and M.C. Chaturvedi: Dependence of creep fracture of inconel 718 on grain boundary precipitates. Acta Mater., 1997, vol. 45, pp. 2735–746. https://doi.org/10.1016/S1359-6454(96)00399-0.10.1016/S1359-6454(96)00399-0 ↗
10. K. Chen, J. Dong, and Z. Yao: Creep failure and damage mechanism of inconel 718 alloy at 800–900 °C. Met. Mater. Int., 2021, vol. 27, pp. 970–84. https://doi.org/10.1007/s12540-019-00447-4.10.1007/s12540-019-00447-4 ↗
11. S. Wu, H.Y. Song, H.Z. Peng, P.D. Hodgson, H. Wang, X.H. Wu, Y.M. Zhu, M.C. Lam, and A.J. Huang: A microstructure-based creep model for additively manufactured nickel-based superalloys. Acta Mater., 2022, vol. 224, 117528https://doi.org/10.1016/j.actamat.2021.117528.10.1016/j.actamat.2021.117528 ↗
12. T.J. Oros, K. Son, A.M. Hodge, and M.E. Kassner: The high temperature creep and fracture behavior of inconel 718 produced by additive manufacturing. Scr. Mater., 2024, vol. 251, 116208https://doi.org/10.1016/j.scriptamat.2024.116208.10.1016/j.scriptamat.2024.116208 ↗
13. G. Bryndza, J.T. Tchuindjang, F. Chen, A.M. Habraken, H. Sepúlveda, V. Tuninetti, A. Mertens, and L. Duchêne: Review of the microstructural impact on creep mechanisms and performance for laser powder bed fusion inconel 718. Materials, 2025, vol. 18, p. 276. https://doi.org/10.3390/ma18020276.10.3390/ma18020276 ↗
14. D.G. Leo Prakash, M.J. Walsh, D. Maclachlan, and A.M. Korsunsky: Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue, Creep and Oxidation. Int. J. Fatigue, 2009, vol. 31, pp. 1966–977. https://doi.org/10.1016/j.ijfatigue.2009.01.023.10.1016/j.ijfatigue.2009.01.023 ↗
15. H. Zhang, C. Li, Q. Guo, Z. Ma, H. Li, and Y. Liu: Improving creep resistance of nickel-based superalloy inconel 718 by tailoring gamma double prime variants. Scr. Mater., 2019, vol. 164, pp. 66–70. https://doi.org/10.1016/j.scriptamat.2019.01.041.10.1016/j.scriptamat.2019.01.041 ↗
16. T. Trosch, J. Strößner, R. Völkl, and U. Glatzel: Microstructure and mechanical properties of selective laser melted inconel 718 compared to forging and casting. Mater. Lett., 2016, vol. 164, pp. 428–31. https://doi.org/10.1016/j.matlet.2015.10.136.10.1016/j.matlet.2015.10.136 ↗
17. J.E. Kanyo, S. Schafföner, R.S. Uwanyuze, and K.S. Leary: An overview of ceramic molds for investment casting of nickel superalloys. J. Eur. Ceram. Soc., 2020, vol. 40, pp. 4955–973. https://doi.org/10.1016/j.jeurceramsoc.2020.07.013.10.1016/j.jeurceramsoc.2020.07.013 ↗
18. Y. Zhao, K. Li, M. Gargani, and W. Xiong: A comparative analysis of inconel 718 made by additive manufacturing and suction casting: microstructure evolution in homogenization. Addit. Manuf., 2020, vol. 36, 101404https://doi.org/10.1016/j.addma.2020.101404.10.1016/j.addma.2020.101404 ↗
19. D. Zhang, Z. Feng, C. Wang, W. Wang, Z. Liu, and W. Niu: Comparison of microstructures and mechanical properties of inconel 718 alloy processed by selective laser melting and casting. Mater. Sci. Eng. A, 2018, vol. 724, pp. 357–67. https://doi.org/10.1016/j.msea.2018.03.073.10.1016/j.msea.2018.03.073 ↗
20. L.-A. Chicos, J. Rodríguez, I. Cañadas, J. Galindo, G. Cempura, A. Kruk, M. Ziętara, A. Gruszczyński, M.A. Pop, S.M. Zaharia, et al.: Application of concentrated solar energy in postprocessing of selective laser melted ti6al4v alloy through simultaneously gas nitriding and heat treatment. Sci. Rep., 2025, vol. 15, p. 28193. https://doi.org/10.1038/s41598-025-13552-9.10.1038/s41598-025-13552-9 ↗
21. Patel, S.; deBarbadillo, J.; Coryell, S. Superalloy 718: Evolution of the alloy from high to low temperature application. In; 2018; pp. 23–49.10.1007/978-3-319-89480-5_2 ↗
22. A.J. Ardell: Precipitation hardening. Metall. Trans. A, 1985, vol. 16, pp. 2131–165. https://doi.org/10.1007/BF02670416.10.1007/BF02670416 ↗
23. J. He, X.Y. Tang, S. Fukuyama, and K. Yokogawa: Boundary in Γ″ precipitates in inconel 718 nickel-base superalloy. Acta Metall. Mater., 1995, vol. 43, pp. 4403–409. https://doi.org/10.1016/0956-7151(95)00124-E.10.1016/0956-7151(95)00124-E ↗
24. V. Beaubois, J. Huez, S. Coste, O. Brucelle, and J. Lacaze: Short term precipitation kinetics of delta phase in strain free inconel* 718 alloy. Mater. Sci. Technol., 2004, vol. 20, pp. 1019–026. https://doi.org/10.1179/026708304225019830.10.1179/026708304225019830 ↗
25. S. Azadian, L.-Y. Wei, and R. Warren: Delta phase precipitation in inconel 718. Mater Charact, 2004, vol. 53, pp. 7–16. https://doi.org/10.1016/j.matchar.2004.07.004.10.1016/j.matchar.2004.07.004 ↗
26. P.J. Páramo-Kañetas, E.A. Orozco-Mendoza, J. Calvo, J.-M. Cabrera-Marrero, M.A. Zamora-Antuñano, and M.P. Guerrero-Mata: Microstructural analysis of a partially recrystallized nickel-based superalloy undergoing delta-processing. J. Alloys Compd., 2022, vol. 907, 164403https://doi.org/10.1016/j.jallcom.2022.164403.10.1016/j.jallcom.2022.164403 ↗
27. V. Imayev, S. Mukhtarov, K. Mukhtarova, A. Ganeev, R. Shakhov, N. Parkhimovich, and A. Logunov: Influence of forging and heat treatment on the microstructure and mechanical properties of a heavily alloyed ingot-metallurgy nickel-based superalloy. Metals (Basel), 2020, vol. 10, p. 1606. https://doi.org/10.3390/met10121606.10.3390/met10121606 ↗
28. Donachie, M.J.; Donachie, S.J. Superalloys; ASM International, 2002; ISBN 978-1-62708-267-9.10.31399/asm.tb.stg2.9781627082679 ↗
29. U.S.A. Special Metals Corporation, Special Metals, Chemical Composition (2007). www.Specialmetals.com (Accessed June 24, 2025).
30. ASTM B637 SpecificationStandard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Bar, Forging, and Ring, (n.d.). https://boltport.com/specifications/astm-b637/ (Accessed June 24, 2025).
31. C. Wang and R. Li: Effect of double aging treatment on structure in inconel 718 alloy. J. Mater. Sci., 2004, vol. 39, pp. 2593–595. https://doi.org/10.1023/B:JMSC.0000020036.96777.9c.10.1023/B:JMSC.0000020036.96777.9c ↗
32. G.A. Rao, M. Srinivas, and D.S. Sarma: Effect of solution treatment temperature on microstructure and mechanical properties of hot isostatically pressed superalloy inconel* 718. Mater. Sci. Technol., 2004, vol. 20, pp. 1161–170. https://doi.org/10.1179/026708304225022124.10.1179/026708304225022124 ↗
33. R.K. Mishra and C. Beura: Life consumption assessment of a large jet engine. J. Fail. Anal. Prev., 2014, vol. 14, pp. 519–29. https://doi.org/10.1007/s11668-014-9842-2.10.1007/s11668-014-9842-2 ↗
34. U. Kale: Assessing the impact of climate change on aircraft engine performance during different flight phases (take-off and cruise) and the environmental consequences. Aircr. Eng. Aerosp. Technol., 2024, vol. 96, pp. 912–20. https://doi.org/10.1108/AEAT-04-2024-0122.10.1108/AEAT-04-2024-0122 ↗
35. M. Naeem: Implications of day temperature variation for an aero-engine’s HP turbine-blade’s creep life-consumption. Aerosp. Sci. Technol., 2009, vol. 13, pp. 27–35. https://doi.org/10.1016/j.ast.2008.02.004.10.1016/j.ast.2008.02.004 ↗
36. Q. Wang, S. Ge, D. Wu, H. Ma, J. Kang, M. Liu, T. Wang, B. Narayanaswamy, and R. Su: Evolution of microstructural characteristics during creep behavior of inconel 718 alloy. Mater. Sci. Eng. A, 2022, vol. 857, 143859https://doi.org/10.1016/j.msea.2022.143859.10.1016/j.msea.2022.143859 ↗
37. J. Belan, L. Kuchariková, A. Vaško, and E. Tillová: Applied heat treatment and its influence on in 718 alloy fatigue life. Manuf. Technol., 2016, vol. 16, pp. 865–70. https://doi.org/10.21062/ujep/x.2016/a/1213-2489/MT/16/5/865.10.21062/ujep/x.2016/a/1213-2489/MT/16/5/865 ↗
38. D. Jianxin, X. Xishan, and Z. Shouhua: Coarsening behavior of Γ″ precipitates in modified inconel 718 Superalloy. Scr. Metall. Mater., 1995, vol. 33, pp. 1933–940. https://doi.org/10.1016/0956-716X(95)00446-3.10.1016/0956-716X(95)00446-3 ↗
39. Holzer L, C.M. Review of FIB Tomography. In Nanofabrication Using Focused Ion and Electron Beams: Principles and Applications; Ivo Utke, Stanislav Moshkalev, Phillip Russell, Eds.; 2012 ISBN 9780199734214.
40. Kruk Adam Electron Tomography and Its Application in Imaging and Metrology of the Microstructure of Materials; Dissertations Monographs / Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie , 2012;
41. J.O. Andersson, T. Helander, L. Höglund, P. Shi, and B. Sundman: Thermo-calc & DICTRA, computational tools for materials science. Calphad, 2002, vol. 26, pp. 273–312. https://doi.org/10.1016/S0364-5916(02)00037-8.10.1016/S0364-5916(02)00037-8 ↗
42. S.H. Fu, J.X. Dong, M.C. Zhang, and X.S. Xie: Alloy Design and Development of INCONEL718 Type Alloy. Mater. Sci. Eng. A, 2009, vol. 499, pp. 215–20. https://doi.org/10.1016/j.msea.2007.11.115.10.1016/j.msea.2007.11.115 ↗
43. A. Ul-Hamid: Contrast formation in the SEM, in A beginners’ guide to scanning electron microscopy. Springer International Publishing, Cham, 2018, pp. 77–128.10.1007/978-3-319-98482-7_3 ↗
44. J. Schindelin, I. Arganda-Carreras, E. Frise, V. Kaynig, M. Longair, T. Pietzsch, S. Preibisch, C. Rueden, S. Saalfeld, B. Schmid, et al.: Fiji: an open-source platform for biological-image analysis. Nat. Methods, 2012, vol. 9, pp. 676–82. https://doi.org/10.1038/nmeth.2019.10.1038/nmeth.2019 ↗
45. Dragonfly 2022.2 [Computer Software]. Comet Technologies Canada Inc., Montreal, Canada; Software Available at https://www.theobjects.com/dragonfly.
46. G. Cempura and A. Kruk: Precipitation processes in sanicro 25 steel at 700–900 °C: experimental study and digital twin simulation. Materials, 2025, vol. 18, p. 3594. https://doi.org/10.3390/ma18153594.10.3390/ma18153594 ↗
47. FEI Company Website—FEI Application Note AN0027 07-2010: ChemiSTEMTM Technology, A Revolution in EDX Analytics Available online: http://www.fei.com.
48. Gatan Digital Micrograph Software.
49. Stadelmann, P. JEMS Java Electron Microscopy Software.
50. M.J. Hÿtch, E. Snoeck, and R. Kilaas: Quantitative measurement of displacement and strain fields from HREM micrographs. Ultramicroscopy, 1998, vol. 74, pp. 131–46. https://doi.org/10.1016/S0304-3991(98)00035-7.10.1016/S0304-3991(98)00035-7 ↗
51. P. Ajay and V.V. Dabhade: Heat treatments of inconel 718 nickel-based superalloy: a review. Met. Mater. Int., 2025, vol. 31, pp. 1204–231. https://doi.org/10.1007/s12540-024-01812-8.10.1007/s12540-024-01812-8 ↗
52. J.P. Collier, S.H. Wong, J.K. Tien, and J.C. Phillips: The effect of varying AI, Ti,and Nb content on the phase stability of INCONEL 718. Metall. Trans. A, 1988, vol. 19, pp. 1657–666. https://doi.org/10.1007/BF02645133.10.1007/BF02645133 ↗
53. W. Zhang, F. Liu, F. Liu, C. Huang, L. Liu, Y. Zheng, and X. Lin: Effect of Al content on microstructure and microhardness of inconel 718 superalloy fabricated by laser additive manufacturing. J. Market. Res., 2022, vol. 16, pp. 1832–845. https://doi.org/10.1016/j.jmrt.2021.12.127.10.1016/j.jmrt.2021.12.127 ↗
54. X. Xie, J.D.G.W.W.Y.J.D.C.Z.Z.W.T.C. The Effect of Nb, Ti, Al on Precipitation and Strengthening Behavior of 718 Type Superalloys. In Superalloys 718; TMS, 2005; pp. 625–706.10.7449/2005/Superalloys_2005_287_298 ↗
55. Shuhong Fu, J.D.M.Z.N.W.X.X. Research on Inconel 718 Type Alloys with Improvement of Temperature Capability. In 7th International Symposium on Superalloy; TMS, 2010; pp. 281–296.10.7449/2010/Superalloys_2010_281_296 ↗
56. A.J. Goodfellow, E.I. Galindo-Nava, K.A. Christofidou, N.G. Jones, T. Martin, P.A.J. Bagot, C.D. Boyer, M.C. Hardy, and H.J. Stone: Gamma prime precipitate evolution during aging of a model nickel-based superalloy. Metall. and Mater. Trans. A., 2018, vol. 49, pp. 718–28. https://doi.org/10.1007/s11661-017-4336-y.10.1007/s11661-017-4336-y ↗
57. D.C. Russ: Practical stereology, Springer Science & Business Media, Berlin, 2012.
58. West, M.J. Introduction to Stereology. Cold Spring Harb Protoc 2012, 2012, pdb.top070623, https://doi.org/10.1101/pdb.top070623.10.1101/pdb.top070623 ↗
59. S. Lech, A. Kruk, G. Cempura, A. Gruszczyński, A. Gil, A. Agüero, A.M. Wusatowska-Sarnek, and A. Czyrska-Filemonowicz: Influence of high-temperature exposure on the microstructure of ATI 718Plus superalloy studied by electron microscopy and tomography techniques. J. Mater. Eng. Perform., 2020, vol. 29, pp. 1453–459. https://doi.org/10.1007/s11665-019-04474-5.10.1007/s11665-019-04474-5 ↗
60. M.D. Uchic, M.A. Groeber, D.M. Dimiduk, and J.P. Simmons: 3D Microstructural characterization of nickel superalloys via serial-sectioning using a dual beam FIB-SEM. Scr. Mater., 2006, vol. 55, pp. 23–28. https://doi.org/10.1016/j.scriptamat.2006.02.039.10.1016/j.scriptamat.2006.02.039 ↗
61. International Conference on 3D Materials Science; De Graef, M., Poulsen, H.F., Lewis, A., Simmons, J., Spanos, G., Eds.; John Wiley & Sons, Inc.: Hoboken, NJ, USA, 2012; ISBN 9781118686768.
62. A. Kruk and G. Cempura: Application of analytical electron microscopy and FIB-SEM tomographic technique for phase analysis in as-cast allvac 718plus superalloy. Int. J. Mater. Res., 2019, vol. 110, pp. 3–10. https://doi.org/10.3139/146.111678.10.3139/146.111678 ↗
63. J.C. Tucker, L.H. Chan, G.S. Rohrer, M.A. Groeber, and A.D. Rollett: Comparison of grain size distributions in a Ni-based superalloy in three and two dimensions using the saltykov method. Scr. Mater., 2012, vol. 66, pp. 554–57. https://doi.org/10.1016/j.scriptamat.2012.01.001.10.1016/j.scriptamat.2012.01.001 ↗
64. A. Bagri, G. Weber, J.-C. Stinville, W. Lenthe, T. Pollock, C. Woodward, and S. Ghosh: Microstructure and property-based statistically equivalent representative volume elements for polycrystalline ni-based superalloys containing annealing twins. Metall. and Mater. Trans. A., 2018, vol. 49, pp. 5727–744. https://doi.org/10.1007/s11661-018-4858-y.10.1007/s11661-018-4858-y ↗
65. H.J. Penkalla, J. Wosik, and A. Czyrska-Filemonowicz: Quantitative microstructural characterisation of Ni-base superalloys. Mater. Chem. Phys., 2003, vol. 81, pp. 417–23. https://doi.org/10.1016/S0254-0584(03)00037-3.10.1016/S0254-0584(03)00037-3 ↗
66. J. Wosik, B. Dubiel, A. Kruk, H.-J. Penkalla, F. Schubert, and A. Czyrska-Filemonowicz: Stereological estimation of microstructural parameters of nickel-based superalloy waspaloy using TEM methods. Mater Charact, 2001, vol. 46, pp. 119–23. https://doi.org/10.1016/S1044-5803(01)00112-7.10.1016/S1044-5803(01)00112-7 ↗
67. T. Wejrzanowski, M. Lewandowska, and K.J. Kurzydłowski: Stereology of nano-materials. Image Anal. Stereol., 2011, vol. 29, p. 1. https://doi.org/10.5566/ias.v29.p1-12.10.5566/ias.v29.p1-12 ↗
68. T. Li, S. Shimasaki, S. Taniguchi, and S. Narita: Reliability of inclusion statistics in steel by stereological methods. ISIJ Int., 2016, vol. 56, pp. 1625–633. https://doi.org/10.2355/isijinternational.ISIJINT-2016-269.10.2355/isijinternational.ISIJINT-2016-269 ↗
69. D.E. Newbury and N.W.M. Ritchie: Is scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDS) quantitative? Scanning, 2013, vol. 35, pp. 141–68. https://doi.org/10.1002/SCA.21041.10.1002/SCA.21041 ↗
70. D.E. Newbury and N.W.M. Ritchie: Electron-excited X-ray microanalysis by energy dispersive spectrometry at 50: analytical accuracy, precision, trace sensitivity, and quantitative compositional mapping. Microsc. Microanal., 2019, vol. 25, pp. 1075–085. https://doi.org/10.1017/S143192761901482X.10.1017/S143192761901482X ↗
71. H.M. Tawancy: Precipitation characteristics of μ-phase in wrought nickel-base alloys and its effect on their properties. J. Mater. Sci., 1996, vol. 31, pp. 3929–936. https://doi.org/10.1007/BF00352653.10.1007/BF00352653 ↗
72. M. Simonetti and P. Caron: Role and behaviour of μ phase during deformation of a nickel-based single crystal superalloy. Mater. Sci. Eng. A, 1998, vol. 254, pp. 1–12. https://doi.org/10.1016/S0921-5093(98)00766-7.10.1016/S0921-5093(98)00766-7 ↗
73. Z. Wang, Y. Ning, Q. Meng, B. Xie, S. Huang, W. Zhang, and B. Zhang: Effect of 800 °C/10,000 h aging-induced μ phase on plasticity in Ni-Co-Cr based superalloys. Mater Charact, 2025, vol. 222, 114807https://doi.org/10.1016/j.matchar.2025.114807.10.1016/j.matchar.2025.114807 ↗
74. Y. Rong, S. Chen, G.-X. Hu, M. Gao, and R.P. Wei: Prediction and characterization of variant electron diffraction patterns for Γ″ and δ precipitates in an INCONEL 718 Alloy. Metall. and Mater. Trans. A., 1999, vol. 30, pp. 2297–303. https://doi.org/10.1007/s11661-999-0239-x.10.1007/s11661-999-0239-x ↗
75. W.-S. Xu, X.-P. Yang, and W.-Z. Zhang: Interpretation of the habit plane of δ precipitates in superalloy inconel 718. Acta Metallurgica Sinica (English Letters), 2018, vol. 31, pp. 113–26. https://doi.org/10.1007/s40195-017-0693-1.10.1007/s40195-017-0693-1 ↗
76. H.Y. Zhang, S.H. Zhang, M. Cheng, and Z.X. Li: Deformation characteristics of δ phase in the delta-processed inconel 718 alloy. Mater Charact, 2010, vol. 61, pp. 49–53. https://doi.org/10.1016/j.matchar.2009.10.003.10.1016/j.matchar.2009.10.003 ↗
77. C. Kumara, D. Deng, J. Moverare, and P. Nylén: Modelling of anisotropic elastic properties in alloy 718 built by electron beam melting. Mater. Sci. Technol., 2018, vol. 34, pp. 529–37. https://doi.org/10.1080/02670836.2018.1426258.10.1080/02670836.2018.1426258 ↗
78. Y. Ji, Y. Lou, M. Qu, J.D. Rowatt, F. Zhang, T.W. Simpson, and L.-Q. Chen: Predicting coherency loss of gamma prime precipitates in IN718 superalloy. Metall. and Mater. Trans. A., 2016, vol. 47, pp. 3235–247. https://doi.org/10.1007/s11661-016-3480-0.10.1007/s11661-016-3480-0 ↗
79. M. Sundararaman, J.B. Singh, and P. Mukhopadhyay: estimation of order strengthening in inconel 718 type alloys containing all Γ″ precipitate variants. Scr. Metall. Mater., 1993, vol. 29, pp. 557–62. https://doi.org/10.1016/0956-716X(93)90165-O.10.1016/0956-716X(93)90165-O ↗
80. S.J. Hong, W.P. Chen, and T.W. Wang: A diffraction study of the Γ″ phase in INCONEL 718 superalloy. Metall. and Mater. Trans. A., 2001, vol. 32, pp. 1887–901. https://doi.org/10.1007/s11661-001-0002-4.10.1007/s11661-001-0002-4 ↗
81. Jonathan Peters Strain++ 2025.
82. R.Y. Zhang, H.L. Qin, Z.N. Bi, J. Li, S. Paul, T.L. Lee, S.Y. Zhang, J. Zhang, and H.B. Dong: Temperature-dependent misfit stress in gamma double prime strengthened Ni-base superalloys. Metall. and Mater. Trans. A., 2020, vol. 51, pp. 1860–873. https://doi.org/10.1007/s11661-020-05627-1.10.1007/s11661-020-05627-1 ↗
83. C. Slama, C. Servant, and G. Cizeron: Aging of the inconel 718 alloy between 500 and 750 °C. J. Mater. Res., 1997, vol. 12, pp. 2298–316. https://doi.org/10.1557/JMR.1997.0306.10.1557/JMR.1997.0306 ↗
84. R.Y. Zhang, H.L. Qin, Z.N. Bi, J. Li, S. Paul, T.L. Lee, S.Y. Zhang, J. Zhang, and H.B. Dong: Evolution of lattice spacing of gamma double prime precipitates during aging of polycrystalline Ni-base superalloys: an in situ investigation. Metall. and Mater. Trans. A., 2020, vol. 51, pp. 574–85. https://doi.org/10.1007/s11661-019-05536-y.10.1007/s11661-019-05536-y ↗
85. Eiselstein, H.L. Metallurgy of a Columbium-Hardened Nickel-Chromium-Iron Alloy. In Advances in the Technology of Stainless Steels and Related Alloys; ASTM International100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, 1965; pp. 62–79.10.1520/STP43733S ↗
86. L.M. Camus and G. Engberg: Goran elevated temperature deformation of cast inconel 718. High Temper. Mater. Proc., 1990, vol. 9, pp. 27–38. https://doi.org/10.1515/HTMP.1990.9.1.27.10.1515/HTMP.1990.9.1.27 ↗
87. M. Fukuhara and A. Sanpei: Elastic moduli and internal frictions of inconel 718 and Ti-6Al-4V as a function of temperature. J. Mater. Sci. Lett., 1993, vol. 12, pp. 1122–124. https://doi.org/10.1007/BF00420541.10.1007/BF00420541 ↗
88. H.H. Smith and D.J. Michel: Effect of environment on fatigue crack propagation behavior of alloy 718 at elevated temperatures. Metall. Trans. A, 1986, vol. 17, pp. 370–74. https://doi.org/10.1007/BF02643920.10.1007/BF02643920 ↗
89. Z. Yan, Q. Tan, H. Huang, H. Qin, Y. Rong, Z. Bi, R. Li, Y. Ren, and Y. Wang: Phase evolution and thermal expansion behavior of a Γ′ precipitated ni-based superalloy by synchrotron X-ray diffraction. Acta Metallurgica Sinica (English Letters), 2022, vol. 35, pp. 93–102. https://doi.org/10.1007/s40195-021-01321-2.10.1007/s40195-021-01321-2 ↗
90. Suresh Babu V; Pavlovic A.S.; Seehra Mohindar S. Oxidation Characteristics and Thermal Expansion of Inconel Alloy 718 from 300 K to 1273 K. In SUPERALLOYS 718, 625, 706 AND DERIVATIVES ; 1997.10.7449/1997/Superalloys_1997_689_693 ↗
91. Y. Han, P. Deb, and M.C. Chaturvedi: Coarsening behaviour of Γ″- and Γ′-particles in inconel alloy 718. Metal. Sci., 1982, vol. 16, pp. 555–62. https://doi.org/10.1179/030634582790427118.10.1179/030634582790427118 ↗
92. C.Q. Ru: Eshelby inclusion of arbitrary shape in an anisotropic plane or half-plane. Acta Mech., 2003, vol. 160, pp. 219–34. https://doi.org/10.1007/s00707-002-0972-3.10.1007/s00707-002-0972-3 ↗
93. T. Mura: Micromechanics of defects in solids, Springer Netherlands, Dordrecht, 1987.10.1007/978-94-009-3489-4 ↗
94. J.D. Eshelby: The determination of the elastic field of an ellipsoidal inclusion, and related problems. Proc. R. Soc. Lond. A Math. Phys. Sci., 1957, vol. 241, pp. 376–96. https://doi.org/10.1098/rspa.1957.0133.10.1098/rspa.1957.0133 ↗