The Effect of Crystallographic Texture on the Constant-Stress, Constant-Heating-Rate Mechanical Test
Source abstract
Abstract
The effect of texture on plastic flow during the constant-stress, constant-heating-rate (CSCHR) mechanical test was established using Ti–6Al–4V sheet material with a strong basal-transverse starting texture. For this purpose, test samples were cut parallel to either the rolling direction (RD) or the long transverse direction (TD) of the sheet. CSCHR testing comprised preheating/soaking at 538 °C followed by heating at a constant rate of 75 °C/min while applying a constant true stress of 103, 172, or 276 MPa. The resulting plastic-strain-vs-time/temperature curves all exhibited a very low rate of straining at low temperatures followed by increasing strain rates at higher temperatures. For each applied stress level, the onset of high-strain-rate deformation occurred at a higher temperature for the TD sample than for the corresponding RD sample. The difference in RD and TD observations was successfully interpreted in terms of a constitutive relation incorporating a strength coefficient dependent on texture as quantified by measured Taylor Factors. A moderate effect of texture on cavitation and fracture was also noted. Specifically, cavities initiated along the boundaries between (hard) alpha particles and the (soft) beta matrix, leading to higher cavity growth rates and lower ductility in TD samples for a given applied stress. Such observations were ascribed to the texture dependence of local stress triaxiality and hence the cavity-growth rate. In addition, an observed effect of peak temperature on ductility was ascribed to the temperature dependence of the cavity growth rate.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. W.A. Backofen: Deformation Processing, Addison-Wesley, Reading, 1972.
2. W.F. Hosford and W.A. Backofen: Fundamentals of Deformation Processing, Syracuse University Press, Syracuse, 1964, pp. 259–98.
3. U.F. Kochs, C.N. Tome, and H.-R. Wenk: Texture and Anisotropy, Cambridge University Press, Cambridge, 1998.
4. K. Ankamma, D.V.V. Satyanarayana, G. Chandramohan Reddy, M. Komaraiah, and N. Eswara Prasad: Sadhana, 2011, vo. 36 (#2), pp. 223–49.10.1007/s12046-011-0016-6 ↗
5. R.L. Whiteley: Trans. ASM, 1960, vol. 52, pp. 154–64.
6. S. Basak, S.K. Panda, and M-G. Lee: Inter. J. Mech. Sci., 2020, vol. 170, paper 105346.10.1016/j.ijmecsci.2019.105346 ↗
7. Z. Marciniak and K. Kuczynski: Inter. J. Mech. Sci., 1967, vol. 9, pp. 609–20.10.1016/0020-7403(67)90066-5 ↗
8. F. Larson and A. Zarkades: Properties of Textured Titanium Alloys, Report MCIC 74-20, Metals and Ceramics Information Center, Battelle’s Columbus Laboratories, Columbus, OH, 1974.10.21236/AD0781884 ↗
9. A.A. Salem, M.G. Glavicic, and S.L. Semiatin: Mater. Sci. Eng. A, 2008, vol. A496, pp. 169–76.10.1016/j.msea.2008.05.017 ↗
10. D. Lee: Trans. TMS-AIME, 1966, vol. 235, pp. 1077–84.
11. D. Lee and W.A. Backofen: TMS-AIME, 1966, vol. 236, pp. 1696–1704.
12. S.L. Semiatin and T.R. Bieler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1787–99.10.1007/s11661-001-0155-1 ↗
13. O. Kaibyshev, I.V. Kazachkov, and R.M. Galeev: J. Mater. Sci., 1981, vol. 16, pp. 2501–06.10.1007/BF01113587 ↗
14. L. da Silva, G. Sivaswamy, L. Sun, and S. Rahimi: Mater. Sci. Eng. A, 2021, vol. A819, paper 141367.10.1016/j.msea.2021.141367 ↗
15. P.G. Partridge, D.S. McDarmaid, and A.W. Bowen: Acta Metall., 1985, vol. 33, pp. 571–77.10.1016/0001-6160(85)90021-5 ↗
16. A.W. Bowen, D.S. McDarmaid, and P.G. Partridge: J. Mater. Sci., 1991, vol. 26, pp. 3457–62.10.1007/BF00557131 ↗
17. D.V. Dunford, A. Wisbey, and P.G. Partridge: Mater. Sci. Technol., 1991, vol. 7, pp. 62–70.10.1179/mst.1991.7.1.62 ↗
18. C. Cheng, Z. Chen, H.E. Li, X. Wang, S. Zhu, and Q. Wang: Mater. Sci. Eng. A, 2021, vol. A800, paper 140362.10.1016/j.msea.2020.140362 ↗
19. W. Li, Z. Chen, J. Liu, Q. Wang, and G. Sui: Mater. Sci. Eng. A, 2017, vol. A688, pp. 322–29.10.1016/j.msea.2017.01.098 ↗
20. S.L. Semiatin, P.N. Fagin, N.C. Levkulich, B.T. Gockel, B.F. Antolovich, E.M. Crist, J. Cormier, and J.S. Tiley: Metall. Mater. Trans. A, 2022, vol. 53A, pp. 394–406.10.1007/s11661-021-06510-3 ↗
21. S.L. Semiatin, N.C. Levkulich, C.A. Heck, A.E. Mann, N. Bozzolo, A.L. Pilchak, and J.S. Tiley: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 2291–2305.10.1007/s11661-020-05673-9 ↗
22. O.I.M. Analysis: Version 8.0, EDAX Corporation, Mahwah, 2016.
23. L. Briottet, J.J. Jonas, and F. Montheillet: Acta Mater., 1996, vol. 44, pp. 1665–72.10.1016/1359-6454(95)00257-X ↗
24. N.E. Paton and W.A. Backofen: Metall. Trans., 1970, vol. 1, pp. 2839–47.10.1007/BF03037822 ↗
25. J.C. Williams, R.G. Baggerly, and N.E. Paton: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 837–50.10.1007/s11661-002-0153-y ↗
26. S.L. Semiatin, F. Montheillet, G. Shen, and J.J. Jonas: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2719–27.10.1007/s11661-002-0394-9 ↗
27. S.L. Semiatin and G.D. Lahoti: Metall. Trans. A, 1981, vol. 12A, pp. 1705–17.10.1007/BF02643753 ↗
28. A.K. Ghosh and R.A. Ayres: Metall. Trans. A, 1976, vol. 7A, pp. 1589–91.10.1007/BF02656404 ↗
29. D.A. Woodford: Trans. ASM, 1969, vol. 62, pp. 291–93.
30. P.D. Nicolaou, A.K. Ghosh, and S.L. Semiatin: in Fundamentals of Modeling for Metals Processing, ASM Handbook, Volume 22A, D.U. Furrer and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2009, pp. 325–38.10.31399/asm.hb.v22a.a0005421 ↗
31. P.D. Nicolaou, S.L. Semiatin, and A.K. Ghosh: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1425–34.10.1007/s11661-000-0260-6 ↗
32. P.D. Nicolaou, A.K. Ghosh, and S.L. Semiatin: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2187–90.10.1007/s11661-004-0170-0 ↗
33. S.L. Semiatin, A.K. Ghosh, and J.J. Jonas: Metall. Trans. A, 1985, vol. 16, pp. 2291–98.10.1007/BF02670429 ↗
34. S.L. Semiatin and J.J. Jonas: Formability and Workability of Metals: Plastic Instability and Flow Localization, American Society for Metals, Metals Park, 1984.
35. S.L. Semiatin, M. Obstalecki, E.J. Payton, A.L. Pilchak, P.A. Shade, N.C. Levkulich, J.M. Shank, D.C. Pagan, F. Zhang, and J.S. Tiley: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 2356–70.10.1007/s11661-019-05164-6 ↗
36. S.L. Semiatin, S.L. Knisley, P.N. Fagin, F. Zhang, and D.R. Barker: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2377–86.10.1007/s11661-003-0300-0 ↗
37. M. Kulakov, S. Rahimi, and S.L. Semiatin: Metall. Mater. Trans. A, 2022, vol. 53A, pp. 407–19.10.1007/s11661-021-06493-1 ↗