journal article·2022-09

Crucial Microstructural Features to Determine the Mechanical Properties of Welded Joints in a Cu-Containing Low-Carbon Low-Alloy Steel After Postweld Heat Treatment

Jinliang Wang, Guangqi Dong, Youchi Li, Xiaohui Xi, Liqing Chen

Publisher page

Abstract

The effect of welding and postweld heat treatment on the microstructural characteristics and mechanical properties of a Cu-containing low-carbon low-alloy steel was studied. The obtained results indicated that ferrite, bainite, and coarse Cu-rich precipitates formed in the weld metal (WM) were responsible for its low impact energy of 57 J at − 40 °C. To obtain a good balance between strength and toughness in the WM, different heat treatments were employed. The obtained results demonstrated that direct tempering had a negligible effect on strength and toughness, but the addition of intercritical annealing to the conventional quenching and tempering process resulted in a significant increase in toughness and a slight decrease in tensile strength. The impact energy was increased to beyond 144 J, and the tensile strength was maintained at a high level of 958 MPa. The optimal microstructure benefiting both toughness and strength was found to primarily comprise intercritical ferrite, tempered martensite/bainite, reversed austenite, and fine Cu-rich precipitates. The toughening mechanism can be explained by the strain-induced martensitic transformation of reversed austenite and the retarding crack propagation effect of high-angle grain boundaries with a misorientation of more than 45 deg. The strengthening mechanism can be rationalized in terms of precipitation-strengthening and the strain-induced martensitic transformation of reversed austenite.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. H.J. Kong, C. Xu, C.C. Bu, C. Da, J.H. Luan, Z.B. Jiao, G. Chen, and C.T. Liu: Acta Mater., 2019, vol. 172, pp. 150–60.10.1016/j.actamat.2019.04.041 ↗
2. S. Vaynman, M. Fine, G. Ghosh, and S. Bhat: Proc. Fourth Mater. Eng. Conf., 1996, pp. 1551–60.
3. S. Vaynman, D. Isheim, R. Prakash Kolli, S.P. Bhat, D.N. Seidman, and M.E. Fine: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 363–73.10.1007/s11661-007-9417-x ↗
4. J. Farren, A. Hunter, J. Dupont, C. Robino, E. Kozeschnik, and D. Seidman: Weld. J., 2013, vol. 92, pp. 140-s-47-s.
5. X. Yu, J.L. Caron, S.S. Babu, J.C. Lippold, D. Isheim, and D.N. Seidman: Acta Mater., 2010, vol. 58, pp. 5596–5609.10.1016/j.actamat.2010.06.031 ↗
6. J.T. Bono, J.N. DuPont, D. Jain, S.-I. Baik, and D.N. Seidman: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 5158–70.10.1007/s11661-015-3087-x ↗
7. J.L. Caron, S.S. Babu, and J.C. Lippold: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 4032–44.10.1007/s11661-011-0951-1 ↗
8. A.S.H. Mousavi, K.M. Aghaie, A.R. Khoshakhlagh, A.R. Eivani, N. Park, and H.R. Jafarian: J. Mater. Res. Technol., 2021, vol. 15, pp. 5776–86.10.1016/j.jmrt.2021.11.013 ↗
9. J.C.F. Jorge, L.F.G. de Souza, M.C. Mendes, I.S. Bott, L.S. Araújo, V.R. dos Santos, J.M.A. Rebello, and G.M. Evans: J. Mater. Res. Technol., 2021, vol. 10, pp. 471–501.10.1016/j.jmrt.2020.12.006 ↗
10. T. Kawakubo, K. Ushioda, and H. Fujii: Mater. Sci. Eng. A, 2021, vol. 832, p. 142350.10.1016/j.msea.2021.142350 ↗
11. V.T.T. Miihkinen and D.V. Edmonds: in Fracture. S.R. Valluri, D.M.R. Taplin, P.R. Rao, J.F. Knott, and R. Dubey, eds., Pergamon, Oxford, 1984, pp. 1481–87.10.1016/B978-1-4832-8440-8.50138-1 ↗
12. Y. Zou, Y.B. Xu, Z.P. Hu, S.Q. Chen, D.T. Han, R.D.K. Misra, and G.Z. Wang: Mater. Sci. Eng. A, 2017, vol. 707, pp. 270–79.10.1016/j.msea.2017.09.059 ↗
13. X. Xi, J. Wang, L. Chen, and Z. Wang: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 5627–39.10.1007/s11661-019-05462-z ↗
14. J. Hu, L.-X. Du, W. Xu, J.-H. Zhai, Y. Dong, Y.-J. Liu, and R.D.K. Misra: Mater. Charact., 2018, vol. 136, pp. 20–28.10.1016/j.matchar.2017.11.058 ↗
15. Z.J. Xie, S.F. Yuan, W.H. Zhou, J.R. Yang, H. Guo, and C.J. Shang: Mater. Des., 2014, vol. 59, pp. 193–98.10.1016/j.matdes.2014.02.035 ↗
16. X. Xi, J. Wang, X. Li, L. Chen, and Z. Wang: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 2912–21.10.1007/s11661-019-05211-2 ↗
17. J. Hu, J.-M. Zhang, G.-S. Sun, L.-X. Du, Y. Liu, Y. Dong, and R.D.K. Misra: J. Mater. Sci., 2019, vol. 54, pp. 6565–78.10.1007/s10853-018-03291-w ↗
18. Y.Y. Song, X.Y. Li, L.J. Rong, D.H. Ping, F.X. Yin, and Y.Y. Li: Mater. Lett., 2010, vol. 64, pp. 1411–14.10.1016/j.matlet.2010.03.021 ↗
19. S.R.F. Lala, A. Gupta, and C. Srivastava: Metall. Mater. Trans. A, 2021, vol. 53, pp. 679–88.10.1007/s11661-021-06545-6 ↗
20. B. Cui, Y. Peng, L. Zhao, M. Peng, T. An, and C. Ma: ISIJ Int., 2016, vol. 56, pp. 132–39.10.2355/isijinternational.ISIJINT-2015-378 ↗
21. Y. You, C. Shang, W. Nie, and S. Subramanian: Mater. Sci. Eng. A, 2012, vol. 558, pp. 692–701.10.1016/j.msea.2012.08.077 ↗
22. Z.J. Xie, G. Han, W.H. Zhou, X.L. Wang, C.J. Shang, and R.D.K. Misra: Scripta Mater., 2018, vol. 155, pp. 164–68.10.1016/j.scriptamat.2018.06.042 ↗
23. M. Wang, Z.Y. Liu, and C.G. Li: Acta Metall. Sin., 2017, vol. 30, pp. 238–337.10.1007/s40195-016-0496-9 ↗
24. S. Zhou, Y. Zuo, Z. Li, X. Wang, and Q. Yong: Mater. Charact., 2016, vol. 119, pp. 110–13.10.1016/j.matchar.2016.07.023 ↗
25. G.R. Lehnhoff and K.O. Findley: JOM, 2014, vol. 66, pp. 756–64.10.1007/s11837-014-0909-z ↗
26. P. Ren, X.P. Chen, L. Mei, Y.Y. Nie, and Q. Liu: Mater. Sci. Eng. A, 2020, vol. 775, p. 138984-.10.1016/j.msea.2020.138984 ↗
27. J. Hu, L.-X. Du, Y. Dong, Q.-W. Meng, and R.D.K. Misra: Mater. Charact., 2019, vol. 152, pp. 21–35.10.1016/j.matchar.2019.04.004 ↗
28. N. Nakada, T. Yamashita, J. Syarif, T. Tsuchiyama, and S. Takaki: Tetsu-to-Hagane, 2003, vol. 89, pp. 1050–56.10.2355/tetsutohagane1955.89.10_1050 ↗
29. X. Pan, G. Qian, and Y. Hong: Scripta Mater., 2021, vol. 194, p. 113631.10.1016/j.scriptamat.2020.113631 ↗
30. W.D. Mu, Y. Cai, and M. Wang: Mater. Sci. Eng. A, 2021, vol. 819, p. 141418.10.1016/j.msea.2021.141418 ↗
31. M.I. Pascuet, E. Martínez, G. Monnet, and L. Malerba: J. Nucl. Mater., 2017, vol. 494, pp. 311–21.10.1016/j.jnucmat.2017.07.049 ↗
32. T. Zhou, H. Yu, and S. Wang: Mater. Sci. Eng. A, 2016, vol. 658, pp. 150–58.10.1016/j.msea.2016.02.001 ↗
33. Y. You, C. Shang, L. Chen, and S. Subramanian: Mater. Sci. Eng. A, 2012, vol. 546, pp. 111–18.10.1016/j.msea.2012.03.038 ↗
34. H. Qiu, L.N. Wang, J.G. Qi, H. Zuo, and K. Hiraoka: Mater. Sci. Eng. A, 2013, vol. 579, pp. 71–76.10.1016/j.msea.2013.05.012 ↗
35. C. Wang, H. Ding, J. Zhang, and H.Y. Wu: Acta Metall. Sin., 2014, vol. 27, pp. 457–63.10.1007/s40195-014-0061-3 ↗
36. S.S. Xu, Y. Zhao, X. Tong, H. Guo, L. Chen, L.W. Sun, M. Peng, M.J. Chen, D. Chen, Y. Cui, G.A. Sun, S.M. Peng, and Z.W. Zhang: J. Alloys Compd., 2017, vol. 712, pp. 573–78.10.1016/j.jallcom.2017.04.143 ↗
37. M.J. Yao, E. Welsch, D. Ponge, S.M.H. Haghighat, S. Sandlöbes, P. Choi, M. Herbig, I. Bleskov, T. Hickel, M. Lipinska-Chwalek, P. Shanthraj, C. Scheu, S. Zaefferer, B. Gault, and D. Raabe: Acta Mater., 2017, vol. 140, pp. 258–73.10.1016/j.actamat.2017.08.049 ↗