journal article·2021-11

Dwell-Fatigue of Ni-Based Superalloys with Serrated and Planar Grain Boundary Morphologies: The Role of the γ′ Phase on Strain Accumulation and Cavitation

John Rotella, Alberto W. Mello, Ajey Venkataraman, Ross Buckingham, Mark Hardy, Michael D. Sangid

Publisher page

Abstract

The effect of grain boundary (GB) morphology on the cavitation behavior in a Ni-based superalloy, RR1000, was studied during elevated temperature dwell-fatigue at 700 °C. Following a solution heat treatment, the material was control cooled at two different rates, resulting in high angle GB morphologies that were tailored as either serrated or planar. The resulting γ′ precipitate structures were characterized near GBs and within grains. Along serrated GBs coarsened and elongated γ′ precipitates formed and consequently created adjacent regions that were denuded of γ′ precipitates. Cyclic dwell-fatigue experiments were performed at low and high stress amplitudes to vary the amount of imparted strain on the specimens. A combination of electron backscatter diffraction and digital image correlation were used to resolve strain localization relative to the GBs, in which strain accumulation was found to precede cavity formation. Additionally, the regions denuded of the γ′ precipitates were observed to localize strain and to be initial sites of cavitation. These results present a quantitative strain analysis between two variants of an RR1000 alloy, which provides the micromechanical rationale to assess the increased proclivity for serrated GBs to form cavities.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. J.L.W. Carter, M.W. Kuper, M.D. Uchic, and M.J. Mills: Mater. Sci. Eng. A., 2014, vol. 605, pp. 127–36. .10.1016/j.msea.2014.03.048 ↗
2. M.E. Kassner and T.A. Hayes: Int. J. Plast., 2003, vol. 19, pp. 1715–48. .10.1016/S0749-6419(02)00111-0 ↗
3. H.Y. Li, J.F. Sun, M.C. Hardy, H.E. Evans, S.J. Williams, T.J.A. Doel, and P. Bowen: Acta Mater., 2015, vol. 90, pp. 355–69. .10.1016/j.actamat.2015.02.023 ↗
4. S. Shinde and P. Gravett: J. ASTM Int., 2011, vol. 8, pp. 1–11. .10.1520/JAI103617 ↗
5. R.E. Stoltz and A.G. Pineau: Mater. Sci. Eng., 1978, vol. 34, pp. 275–84. .10.1016/0025-5416(78)90060-5 ↗
6. D.U. Furrer and H.-J. Fecht: Acta Metall., 1999, vol. 40, pp. 1215–20. .
7. F. Alexandre, S. Deyber, and A. Pineau: Scripta Mater., 2004, vol. 50, pp. 25–30. .10.1016/j.scriptamat.2003.09.043 ↗
8. M. Detrois, J. Rotella, M. Hardy, S. Tin, and M.D. Sangid: Integr. Mater. Manuf. Innov., 2017, https://doi.org/10.1007/s40192-017-0103-6.10.1007/s40192-017-0103-6 ↗
9. H.L. Danflou, M. Marty, and A. Walder: TMS Superalloys, 1992, pp. 63–72.10.7449/1992/Superalloys_1992_63_72 ↗
10. R.J. Mitchell, J.A. Lemsky, R. Ramanathan, H.Y. Li, K.M. Perkins, and L.D. Connor: Superalloys 2008, 2008, pp. 347–56.10.7449/2008/Superalloys_2008_347_356 ↗
11. H.U. Hong, I.S. Kim, B.G. Choi, M.Y. Kim, and C.Y. Jo: Mater. Sci. Eng. A., 2009, vol. 517, pp. 125–31. .10.1016/j.msea.2009.03.071 ↗
12. Y.T. Tang, A.J. Wilkinson, and R.C. Reed: Metall. Mater. Trans. A., 2018, https://doi.org/10.1007/s11661-018-4671-7.10.1007/s11661-018-4671-7 ↗
13. A.K. Koul and G.H. Gessinger: Acta Metall., 1983, vol. 31, pp. 1061–9. .10.1016/0001-6160(83)90202-X ↗
14. A.K. Koul and R. Thamburaj: Metall. Trans. A., 1985, vol. 16, pp. 17–26. .10.1007/BF02656707 ↗
15. R.J. Mitchell, H.Y. Li, and Z.W. Huang: J. Mater. Process. Technol., 2009, vol. 209, pp. 1011–7. .10.1016/j.jmatprotec.2008.03.008 ↗
16. D.M. Knowles and D.W. Hunt: Metall. Mater. Trans. A., 2002, vol. 33A, pp. 3165–72. .10.1007/s11661-002-0302-3 ↗
17. R.C. Gifkins: Mater. Charact., 1994, vol. 32, pp. 59–77. .10.1016/1044-5803(94)90093-0 ↗
18. Y. Shen, W. Li, D.L. Sulsky, and H.L. Schreyer: Int. J. Mech. Sci., 2000, vol. 42, pp. 2167–89. .10.1016/S0020-7403(00)00005-9 ↗
19. L.C. Lim: Acta Metall., 1987, vol. 35, pp. 1663–73. .10.1016/0001-6160(87)90114-3 ↗
20. L.C. Lim: Acta Metall., 1989, vol. 37, pp. 969–77. .10.1016/0001-6160(89)90024-2 ↗
21. B.F. Dyson, M.S. Loveday, and M.J. Rodgers: Proc R. Soc. Lond. A., 1976, vol. 349, pp. 245–59. .10.1098/rspa.1976.0071 ↗
22. J.N. Greenwood, D.R. Miller, and J.W. Suiter: Acta Metall., 1954, vol. 2, pp. 250–8. .10.1016/0001-6160(54)90166-2 ↗
23. R.C. Gifkins: Acta Metall., 1956, vol. 4, pp. 98–9. .10.1016/0001-6160(56)90121-3 ↗
24. H. Riedel: Acta Metall., 1984, vol. 32, pp. 313–21. .10.1016/0001-6160(84)90104-4 ↗
25. D.P. Field and B.L. Adams: Acta Metall. Mater., 1992, vol. 40, pp. 1145–57. .10.1016/0956-7151(92)90413-9 ↗
26. W. Abuzaid, H. Sehitoglu, and J. Lambros: Mater. Sci. Eng. A., 2012, vol. 561, pp. 507–19. .10.1016/j.msea.2012.10.072 ↗
27. L.J. Carroll, C. Cabet, M.C. Carroll, and R.N. Wright: Int. J. Fatigue., 2013, vol. 47, pp. 115–25. .10.1016/j.ijfatigue.2012.07.016 ↗
28. B.F. Dyson and M.J. Rodgers: Met. Sci., 1974, vol. 8, pp. 261–6. .10.1179/msc.1974.8.1.261 ↗
29. P. Kontis, E. Alabort, D. Barba, D.M. Collins, A.J. Wilkinson, and R.C. Reed: Acta Mater., 2017, vol. 124, pp. 489–500. .10.1016/j.actamat.2016.11.009 ↗
30. R.C. Buckingham, C. Argyrakis, M.C. Hardy, and S. Birosca: Mater. Sci. Eng. A., 2016, vol. 654, pp. 317–28. .10.1016/j.msea.2015.12.042 ↗
31. I.M. Parr, T.J. Jackson, M. Hardy, D.J. Child, C. Argyrakis, K. Kevers, V. Saraf, and J.M. Stumpf: Superalloys 2016 Proc. 13th Int. Symp. Superalloys, 2016, pp. 447–56.10.1002/9781119075646.ch48 ↗
32. GRABIT: MATLAB Central File Exchange. https://www.mathworks.com/matlabcentral/fileexchange/7173-grabit. Retrieved April 30, 2015.
33. W.Z. Abuzaid, M.D. Sangid, J.D. Carroll, H. Sehitoglu, and J. Lambros: J. Mech. Phys. Solids., 2012, vol. 60, pp. 1201–20. .10.1016/j.jmps.2012.02.001 ↗
34. Y.L. Dong and B. Pan: Exp. Mech., 2017, vol. 57, pp. 1161–81. .10.1007/s11340-017-0283-1 ↗
35. J. Tracy, A. Waas, and S. Daly: J. Am. Ceram. Soc., 2015, vol. 98, pp. 1898–906. .10.1111/jace.13538 ↗
36. M.A. Sutton, N. Li, D. Garcia, N. Cornille, J.J. Orteu, S.R. McNeill, H.W. Schreier, and X. Li: Meas. Sci. Technol., 2006, vol. 17, p. 2613. .10.1088/0957-0233/17/10/012 ↗
37. A.W. Mello, T.A. Book, A. Nicolas, S.E. Otto, C.J. Gilpin, and M.D. Sangid: Exp. Mech., 2017, vol. 59, pp. 1–15. .
38. A.W. Mello, A. Nicolas, and M.D. Sangid: Mater. Sci. Eng. A., 2017, vol. 695, pp. 332–41. .10.1016/j.msea.2017.04.002 ↗
39. C.A. Schneider, W.S. Rasband, and K.W. Eliceiri: Nat. Methods., 2012, vol. 9, pp. 671–5. .10.1038/nmeth.2089 ↗
40. F. Di Gioacchino and J. Quinta Da Fonseca: Int. J. Plast., 2015, vol. 74, pp. 92–109. .10.1016/j.ijplas.2015.05.012 ↗
41. A. Venkataraman, M. Linne, S. Daly, and M.D. Sangid: Materialia., 2019, https://doi.org/10.1016/j.mtla.2019.100499.10.1016/j.mtla.2019.100499 ↗
42. E.J. Lieberman, A.D. Rollett, R.A. Lebensohn, and E.M. Kober: Model. Simul. Mater. Sci. Eng., 2015, vol. 23, p. 035005. .10.1088/0965-0393/23/3/035005 ↗
43. A. Rovinelli, M.D. Sangid, H. Proudhon, Y. Guilhem, R.A. Lebensohn, and W. Ludwig: J. Mech. Phys. Solids., 2018, vol. 115, pp. 208–29. .10.1016/j.jmps.2018.03.007 ↗
44. F. Bourdin, J.C. Stinville, M.P. Echlin, P.G. Callahan, W.C. Lenthe, C.J. Torbet, D. Texier, F. Bridier, J. Cormier, P. Villechaise, T.M. Pollock, and V. Valle: Acta Mater., 2018, vol. 157, pp. 307–25. .10.1016/j.actamat.2018.07.013 ↗
45. C.L. Qiu and P. Andrews: Mater. Charact., 2013, vol. 76, pp. 28–34. .10.1016/j.matchar.2012.11.012 ↗
46. A.N. Stroh: Proc. R. Soc. A., 1954, vol. 223, pp. 404–14. .
47. J.J. Hauser and B. Chalmers: Acta Metall., 1961, vol. 9, pp. 802–18. .10.1016/0001-6160(61)90183-3 ↗
48. J.D. Livingston and B. Chalmers: Acta Metall., 1957, vol. 5, pp. 322–7. .10.1016/0001-6160(57)90044-5 ↗
49. C. Efstathiou, H. Sehitoglu, and J. Lambros: Int. J. Plast., 2010, vol. 26, pp. 93–106. .10.1016/j.ijplas.2009.04.006 ↗