Determining the Influence of Braze Temperature on the Dissolution Behaviour and Kinetics of Isothermal Solidification During Transient Liquid Phase Bonding (TLPB) Ni-Based Superalloys
Source abstract
Abstract
A method for measuring the full liquid width of a braze joint during TLPB was developed based on enthalpy of solidification values obtained from DSC and microstructural measurements. This differs from most techniques in the literature which only measure the centreline eutectic width using metallographic methods. Comparison of full liquid width and eutectic only measurements confirmed that the rate of isothermal solidification and gap widening due to dissolution is underestimated, particularly at higher braze temperatures, when relying on eutectic measurements only. However, the time for complete isothermal solidification is the same whether considering the full liquid width or eutectic width. The underestimation of the IS rate by eutectic centreline measurements increases as the braze temperature increases above the filler liquidus temperature. The DSC enthalpy measurements were used to build a TLPB processing map for a range of braze temperatures and starting filler metal interlayer thickness. This map can predict the degree of gap widening and the time for complete isothermal solidification for this gap. Results indicate that an optimum braze temperature exists where the apposing influences of gap widening and increased IS rate combine to give the shortest IS completion time.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. O.A. Ojo, N.L Richards, M.C. Chaturvedi, Sci. Tech. Weld. Joining, 2004, 9(6), pp. 532-40.10.1179/174329304X8702 ↗
2. O.A. Idowu, N.L. Richards, M.C. Chaturvedi, Mat. Sci. and Eng. A, 2005, 397, pp. 98-112.10.1016/j.msea.2005.01.055 ↗
3. K. Tokoro, N.P. Wikstrom, O.A Ojo, M.C. Chaturvedi, Mat. Sci. & Eng. A, 2008, 477, pp. 311-318.10.1016/j.msea.2007.05.069 ↗
4. M. Mosallaee, A. Ekrami, K. Ohsasa, K. Matsuura, Met. & Mater. Trans. A, 2008, 39A, pp. 2389- 2402.10.1007/s11661-008-9588-0 ↗
5. A.T. Egbewande. C. Chukwukaeme, O.A. Ojo (2008) Mater. Charact. 59:1051–58.10.1016/j.matchar.2007.08.023 ↗
6. V. Jalilvand, H. Omidvar, M.R. Rahimipour, H.R. Shakeri, Materials and Design, 2013, 52 pp. 36–46.10.1016/j.matdes.2013.05.042 ↗
7. M. Pouranvari, S.M. Mousavizadeh, Mater. Tech., 2015, 49: 247-251.
8. I. Tuah-Poku, M. Dollar, T.B. Massalski, Metallurgical Transactions A, 1988, 19: 675-686.10.1007/BF02649282 ↗
9. K.D. Partz, E. Lugscheider, Welding Journal, 1983, 62, pp. S160-S164.
10. Y. Nakao, K. Nishimoto, K. Shinozaki, C. Kang, Trans. Jpn. Weld. Soc., 1989, 20: 60-65.
11. A. Sakamoto, C. Fujimara, R. Hattori, S. Sakai, Welding Journal, 1989, 68, pp.63-67.
12. M.A. Arafin, M. Medraj, D.P. Turner, P. Bocher, Mat. Sci. Eng. A, 2007, 447:125-133.10.1016/j.msea.2006.10.045 ↗
13. D.C. Murray, S.F. Corbin, J. Mater. Proc. Tech., 2017, 248, pp. 92-102.10.1016/j.jmatprotec.2017.05.013 ↗
14. E.D. Moreau, S.F. Corbin, Met. Mater. Trans. A., 2020, 51: 2882-2892.10.1007/s11661-020-05724-1 ↗
15. C. Tadgell, S.F. Corbin, Can. Met. Quart., 2020, 59:3, pp. 288-296.10.1080/00084433.2020.1741899 ↗
16. A. Ghasemi, M. Pouranvari, Sci. Tech. Weld. Joining, 2018, 23: 441-448.10.1080/13621718.2017.1410341 ↗
17. J. Ruiz-Vargas, N. Siredey-Schwaller, P. Bocher, A. Hazotte, J. Mater. Proc. Tech., 2013, 213, pp. 2074-80.10.1016/j.jmatprotec.2013.06.008 ↗
18. X.P. Zhang, Y.W. Shi, Scripta Materialia, 2004, 50, pp. 1003-1006.10.1016/j.scriptamat.2003.12.032 ↗
19. M. Pouranvari, A. Ekrami, A.H. Kokabi, Sci. & Tech. Welding and Joining, 2018, 23: 13–18.10.1080/13621718.2017.1327934 ↗