Effect of Strain Rate on the Mechanical Behavior of Al-Mg Alloy Under a Pulsed Electric Current
Source abstract
Abstract
Abstract In this study, the effect of strain rate on flow stress, material plasticity and, microstructure was analysed for the electrically-assisted tension of the 5754-H111 aluminium alloy. Three different strain rates (0.0025, 0.01, and 0.04 s-1) were applied under a pulsed electric current tension. The study showed that at decreasing strain rate, an increase in engineering strain is observed. This effect was explained by the periodic strain hardening and annealing of the sample under a pulsed electric current. The study also showed the possibility of determining the real value of stress-drop, which occurred when a pulsed current was applied during tension. Finally, applying the current pulses led to a meaningful increase in the material plasticity. It was shown applying pulsed current allowed a change of the dislocation pattern and its annihilation, resulting from the dynamic recovery process. This version of the article has been accepted for publication, after peer review (when applicable) but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/s11661-024-07335-6. Use of this Accepted Version is subject to the publisher’s Accepted Manuscript terms of use https://www.springernature.com/gp/open-research/policies/accepted-manuscript-terms. This research was funded by the National Science Centre, Poland (grant No. 2022/45/N/ST8/03048). For the purpose of Open Access, the author has applied a CC-BY public copyright licence to any Author Accepted Manuscript (AAM) version arising from this submission.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electromagnetic Effects on Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. S. Toros, F. Ozturk, and I. Kacar: J. Mater. Process. Technol., 2008, vol. 207, pp. 1–2.10.1016/j.jmatprotec.2008.03.057 ↗
2. S.M. Mirfalah-Nasiri, A. Basti, and R. Hashemi: Int. J. Mech. Sci., 2016, vol. 117, pp. 93–101.10.1016/j.ijmecsci.2016.08.011 ↗
3. W.A. Salandro and J.T. Roth: Proc. ASME Int. Manuf. Sci. Eng. Conf. 2009, MSEC2009, 2009, vol. 2, pp. 599–608.
4. M.V.N.V. Satyanarayana, A. Kumar, V.K.S. Jain, R. Kumar, and S. Mishra: Arch. Civ. Mech. Eng., 2023, vol. 23, pp. 1–16.
5. H.R. Dong, X.Q. Li, Y. Li, Y.H. Wang, H.B. Wang, X.Y. Peng, and D.S. Li: Int. J. Adv. Manuf. Technol., 2022, vol. 120, pp. 7079–99.10.1007/s00170-022-08996-6 ↗
6. J.H. Roh, J.J. Seo, S.T. Hong, M.J. Kim, H.N. Han, and J.T. Roth: Int. J. Plast., 2014, vol. 58, pp. 84–99.10.1016/j.ijplas.2014.02.002 ↗
7. H.J. Jeong, M.J. Kim, J.W. Park, C.D. Yim, J.J. Kim, O.D. Kwon, P.P. Madakashira, and H.N. Han: Mater. Sci. Eng. A, 2017, vol. 684, pp. 668–76.10.1016/j.msea.2016.12.103 ↗
8. B.H. Xing, T. Huang, K.X. Song, L.J. Xu, N. Xiang, X.W. Chen, and F.X. Chen: J. Mater. Res. Technol., 2022, vol. 21, pp. 1128–40.10.1016/j.jmrt.2022.09.077 ↗
9. S.T. Hong, Y.H. Jeong, M.N. Chowdhury, D.M. Chun, M.J. Kim, and H.N. Han: CIRP Ann. Manuf. Technol., 2015, vol. 64, pp. 277–80.10.1016/j.cirp.2015.04.084 ↗
10. J.Y. Liu and K.F. Zhang: Mater. Sci. Technol. (United Kingdom), 2016, vol. 32, pp. 540–46.10.1179/1743284715Y.0000000120 ↗
11. C.R. Green, T.A. McNeal, and J.T. Roth: in Transactions of the North American Manufacturing Research Institution of SME, Greenville, SC, 2009, pp. 403–10.
12. S. Fu, H. Liu, N. Qi, B. Wang, Y. Jiang, Z. Chen, T. Hu, and D. Yi: Scr. Mater., 2018, vol. 150, pp. 13–17.10.1016/j.scriptamat.2018.02.017 ↗
13. J. Zhao, G.X. Wang, Y. Dong, and C. Ye: J. Appl. Phys., 2007, https://doi.org/10.1063/1.4998938.10.1063/1.4998938 ↗
14. A. Ghiotti, S. Bruschi, E. Simonetto, C. Gennari, I. Calliari, and P. Bariani: CIRP Ann., 2018, vol. 67, pp. 289–92.10.1016/j.cirp.2018.04.054 ↗
15. X. Zhang, H. Li, M. Zhan, Z. Zheng, J. Gao, and G. Shao: J. Mater. Sci. Technol., 2020, vol. 36, pp. 79–83.10.1016/j.jmst.2019.08.008 ↗
16. O.A. Troitskii and V.I. Likhtman: Dokl. Akad. Nauk SSSR, 1963, vol. 148, pp. 332–34.
17. M.I. Molotskii: Mater. Sci. Eng. A, 2000, vol. 287, pp. 248–58.10.1016/S0921-5093(00)00782-6 ↗
18. S. Zhao, R. Zhang, Y. Chong, X. Li, A. Abu-Odeh, E. Rothchild, D.C. Chrzan, M. Asta, J.W. Morris, and A.M. Minor: Nat. Mater., 2021, vol. 20, pp. 468–72.10.1038/s41563-020-00817-z ↗
19. H. Conrad: Mater. Sci. Eng. A, 2000, vol. 287, pp. 276–87.10.1016/S0921-5093(00)00786-3 ↗
20. X. Li, Q. Zhu, Y. Hong, H. Zheng, J. Wang, J. Wang, and Z. Zhang: Nat. Commun., 2022, vol. 13, pp. 1–9.
21. S.J. Kim, S.D. Kim, D. Yoo, J. Lee, Y. Rhyim, and D. Kim: Metall. Mater. Trans. A, 2016, vol. 47, pp. 6368–73.10.1007/s11661-016-3804-0 ↗
22. W. Kang, I. Beniam, and S.M. Qidwai: Rev. Sci. Instrum, 2016, https://doi.org/10.1063/1.4961663.10.1063/1.4961663 ↗
23. X. Li, J. Turner, K. Bustillo, and A.M. Minor: Acta Mater., 2022, vol. 223, p. 117461.10.1016/j.actamat.2021.117461 ↗
24. Y.H. Zhu, S. To, W.B. Lee, X.M. Liu, Y.B. Jiang, and G.Y. Tang: Mater. Sci. Eng. A, 2009, vol. 501, pp. 125–32.10.1016/j.msea.2008.09.080 ↗
25. B. Kinsey, G. Cullen, A. Jordan, and S. Mates: CIRP Ann. Manuf. Technol., 2013, vol. 62, pp. 279–82.10.1016/j.cirp.2013.03.058 ↗
26. Y.E. Adamyan, S.I. Krivosheev, S.G. Magazinov, D.I. Alekseev, and I.S. Kolodkin: Proc. 2019 IEEE Conf. Russ. Young Res. Electr. Electron. Eng. ElConRus 2019, 2019, pp. 792–95.
27. K. Zhao, R. Fan, and L. Wang: J. Mater. Eng. Perform., 2016, vol. 25, pp. 781–89.10.1007/s11665-016-1913-y ↗
28. J. Magargee, F. Morestin, and J. Cao: J. Eng. Mater. Technol. Trans. ASME, 2013, vol. 135, pp. 1–10.10.1115/1.4024394 ↗
29. A.A. Shibkov, A.A. Denisov, M.A. Zheltov, A.E. Zolotov, and M.F. Gasanov: Mater. Sci. Eng. A, 2014, vol. 610, pp. 338–43.10.1016/j.msea.2014.05.050 ↗
30. M.J. Kim, S. Yoon, S. Park, H.J. Jeong, J.W. Park, K. Kim, J. Jo, T. Heo, S.T. Hong, S.H. Cho, Y.K. Kwon, I.S. Choi, M. Kim, and H.N. Han: Appl. Mater. Today, 2020, vol. 21, p. 100874.10.1016/j.apmt.2020.100874 ↗
31. T.J. Grimm and L. Mears: J. Manuf. Process., 2020, vol. 56, pp. 1263–69.10.1016/j.jmapro.2020.04.020 ↗
32. M. Kim, J. Song, and H. Huh: Procedia Eng., 2017, vol. 207, pp. 371–76.10.1016/j.proeng.2017.10.790 ↗
33. J.H. Song, J. Lee, I. Hwang, Y.B. Kim, S. Choi, G.A. Lee, and M.J. Kang: Appl. Mech. Mater., 2013, vol. 389, pp. 284–88.10.4028/www.scientific.net/AMM.389.284 ↗
34. K. Hariharan, M.G. Lee, M.J. Kim, H.N. Han, D. Kim, and S. Choi: Metall. Mater. Trans. A, 2015, vol. 46, pp. 3043–51.10.1007/s11661-015-2879-3 ↗
35. K. Radwański: Steel Res. Int., 2015, vol. 86, pp. 1379–90.10.1002/srin.201400361 ↗
36. B. Wang, B. Tang, C. You, Y. Wan, Y. Gao, Z. Chen, L. Lu, C. Liu, and J. Wang: Mater. Sci. Eng. A, 2020, vol. 775, p. 138789.10.1016/j.msea.2019.138789 ↗
37. H. Wang, W. Song, K. Koenigsmann, S. Zhang, L. Ren, and K. Yang: Mater. Des., 2020, vol. 188, p. 108475.10.1016/j.matdes.2020.108475 ↗
38. M.J. Kim, K. Lee, K.H. Oh, I.S. Choi, H.H. Yu, S.T. Hong, and H.N. Han: Scr. Mater., 2014, vol. 75, pp. 58–61.10.1016/j.scriptamat.2013.11.019 ↗
39. H. Xu, X. Liu, D. Zhang, and X. Zhang: J. Mater. Sci. Technol., 2019, vol. 35, pp. 1108–12.10.1016/j.jmst.2018.12.007 ↗