journal article·2023-07

Enhancement of the Strength–Ductility Balance in Cu–40 Pct Zn Alloy by Single Roll Drive Rolling and Cooling-Assisted Friction Stir Processing

Hoora Mazaheri, Hamed Jamshidi Aval, Roohollah Jamaati

Publisher page

Abstract

This research investigates the effect of pre-straining, heat input, and cooling media on the microstructure and mechanical properties of friction-stir-processed brass. The findings show that in the pre-strained Cu–Zn alloy, applying very low heat and high heat inputs results in longitudinal groove defect formation and heterogeneity in the microstructure of the friction stir processed samples, respectively. Also, extremely high shear deformation during friction stir processing at a rotational speed of 800 rpm and a traverse speed of 100 mm/min under water cooling media results in the formation of fine equiaxed grains (2.2 ± 0.4 μm), ultimate tensile strength (458.2 MPa), yield strength (371.2 MPa), and elongation 10.1 pct. By simultaneous applying pre-rolling and friction stir processing, the grain size of Cu–Zn alloy’s base metal decreases by 95.4 pct. The micro void formation and non-uniformity of the hardness distribution resulting from the heterogeneity in the microstructure of the sample processed at maximum heat input led to minimum tensile strength (249.6 MPa) and elongation (2.1 pct).
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Metallurgy and Material Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. E. Farabi, A. Zarei-Hanzaki, M.H. Pishbin, and M. Moallemi: Mater. Sci. Eng. A, 2015, vol. 641, pp. 360–68.10.1016/j.msea.2015.06.042 ↗
2. S.E. Mousavi, N. Naghshekesh, F. Ahmadi, B. Sadeghi, and P. Cavaliere: Mater. Sci. Eng. A, 2018, vol. 728, pp. 231–38.10.1016/j.msea.2018.05.032 ↗
3. G.M. Xie and L. Geng, Mater. Trans. 2008, pp. 0806090447–0806090447.
4. H.S. Kim, W.Y. Kim, and K.H. Song: J. Alloy. Compd., 2012, vol. 536, pp. S200–S203.10.1016/j.jallcom.2011.11.079 ↗
5. R. Kumar, S.M. Dasharath, P.C. Kang, C.C. Koch, and S. Mula: Mater. Des., 2015, vol. 67, pp. 637–43.10.1016/j.matdes.2014.11.014 ↗
6. S. Mahajan, C.S. Pande, M.A. Imam, and B.B. Rath: Acta Mater., 1997, vol. 45, pp. 2633–38.10.1016/S1359-6454(96)00336-9 ↗
7. T. Leffers and O.B. Pedersen: Scripta Mater., 2002, vol. 46, pp. 741–46.10.1016/S1359-6462(02)00065-9 ↗
8. Y.H. Zhao, Y.T. Zhu, X.Z. Liao, Z. Horita, and T.G. Langdon: Appl. Phys. Lett., 2006, vol. 89, 121906.10.1063/1.2356310 ↗
9. S.M. Dasharath, C.C. Koch, and S. Mula: Mater. Charact., 2015, vol. 110, pp. 14–24.10.1016/j.matchar.2015.10.006 ↗
10. F. Shahriyari, M.H. Shaeri, A. Dashti, Z. Zarei, M. TalafiNoghani, J.H. Cho, and F. Djavanroodi: Mater. Sci. Eng. A, 2022, vol. 831, p. 142149.10.1016/j.msea.2021.142149 ↗
11. H. Naser Radhi, M.T. Mohammed, and A.M.H. Aljassani: Mater. Today, 2021, vol. 44, pp. 2399–2402.
12. E. Farabi, A. Zarei-Hanzaki, M. Moghaddam, P.D. Hodgson, and H. Beladi: Mater. Charact., 2019, vol. 152, pp. 101–14.10.1016/j.matchar.2019.03.039 ↗
13. T. Kunimine, In Materials Science Forum, (Trans Tech Publ: 2021), pp 780–85.10.4028/www.scientific.net/MSF.1016.780 ↗
14. K. Meena, A. Kumar, and S.N. Pandya: Mater. Today, 2017, vol. 4, pp. 1978–87.
15. A. Heidarzadeh, A. Chabok, V. Klemm, and Y. Pei: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 2391–98.10.1007/s11661-019-05175-3 ↗
16. N. Xu, Q. Song, and Y. Bao: Mater. Sci. Technol., 2018, vol. 34, pp. 1768–72.10.1080/02670836.2018.1481625 ↗
17. S. Cartigueyen and K. Mahadevan: IOSR J. Mech. Civil Eng. (IOSR-JMCE), 2014, vol. 70, pp. 6–12.10.9790/1684-11270612 ↗
18. K. Surekha and A. Els-Botes: Mater. Des., 2011, vol. 32, pp. 911–16.10.1016/j.matdes.2010.08.028 ↗
19. Y. Wang, R. Fu, L. Jing, Y. Li, and D. Sang: Mater. Sci. Eng. A, 2017, vol. 703, pp. 470–76.10.1016/j.msea.2017.07.090 ↗
20. P. Xue, B.L. Xiao, and Z.Y. Ma: Mater. Sci. Eng. A, 2012, vol. 532, pp. 106–10.10.1016/j.msea.2011.10.070 ↗
21. A. Heidarzadeh and T. Saeid: Mater. Sci. Eng. A, 2016, vol. 649, pp. 349–58.10.1016/j.msea.2015.10.012 ↗
22. N. Xu, R. Ueji, and H. Fujii: Mater. Sci. Eng. A, 2014, vol. 610, pp. 132–38.10.1016/j.msea.2014.05.037 ↗
23. G.M. Xie, Z.Y. Ma, and L. Geng: Philos. Magn., 2009, vol. 89, pp. 1505–16.10.1080/14786430903019040 ↗
24. C.Y. Liu, B. Qu, P. Xue, Z.Y. Ma, K. Luo, M.Z. Ma, and R.P. Liu: J. Mater. Sci. Technol., 2018, vol. 34, pp. 112–18.10.1016/j.jmst.2017.02.008 ↗
25. I. Vysotskiy, S. Malopheyev, S. Mironov, and R. Kaibyshev: Mater. Sci. Eng. A, 2018, vol. 733, pp. 39–42.10.1016/j.msea.2018.07.026 ↗
26. I. Vysotskiy, S. Malopheyev, S. Mironov, and R. Kaibyshev: Mater. Sci. Eng. A, 2019, vol. 760, pp. 206–13.10.1016/j.msea.2019.05.118 ↗
27. H. Mazaheri, H. Jamshidi Aval, and R. Jamaati: J. Manuf. Process., 2021, vol. 67, pp. 496–502.10.1016/j.jmapro.2021.05.018 ↗
28. H. Mazaheri, H. Jamshidi Aval, and R. Jamaati: Mater. Sci. Eng. A, 2021, vol. 826, p. 141958.10.1016/j.msea.2021.141958 ↗
29. A. Esmaeili, M.K. Besharati Givi, and H.R. Zareie Rajani: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7093–7102.10.1016/j.msea.2011.06.004 ↗
30. C. Meran: Mater. Des., 2006, vol. 27, pp. 719–26.10.1016/j.matdes.2005.05.006 ↗
31. H.S. Park, T. Kimura, T. Murakami, Y. Nagano, K. Nakata, and M. Ushio: Mater. Sci. Eng. A, 2004, vol. 371, pp. 160–69.10.1016/j.msea.2003.11.030 ↗
32. R. Ramesh, I. Dinaharan, E.T. Akinlabi, and N. Murugan: J. Mater. Eng. Perform., 2018, vol. 27, pp. 1544–54.10.1007/s11665-018-3299-5 ↗
33. N. Dialami, M. Cervera, and M. Chiumenti: Eur. J. Mech. A, 2020, vol. 80, 103912.10.1016/j.euromechsol.2019.103912 ↗
34. S. Mukherjee and A.K. Ghosh: Mater. Sci. Eng. A, 2010, vol. 527, pp. 5130–35.10.1016/j.msea.2010.04.091 ↗
35. A. Arora, R. Nandan, A.P. Reynolds, and T. DebRoy: Scripta Mater., 2009, vol. 60, pp. 13–16.10.1016/j.scriptamat.2008.08.015 ↗
36. A. Kar, S. Suwas, and S.V. Kailas: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 5153–73.10.1007/s11661-019-05409-4 ↗
37. A. Kar, D. Yadav, S. Suwas, and S.V. Kailas: Mater. Charact., 2020, vol. 164, p. 110371.10.1016/j.matchar.2020.110371 ↗
38. J.Q. Su, T.W. Nelson, T.R. McNelley, and R.S. Mishra: Mater. Sci. Eng. A, 2011, vol. 528, pp. 5458–64.10.1016/j.msea.2011.03.043 ↗
39. D. Ghahremani Moghadam, K. Farhangdoost, and R. Masoudi Nejad: Metall. Mater. Trans. B, 2016, vol. 47B, pp. 2048–62.10.1007/s11663-016-0611-3 ↗
40. S. Ghadar, A. Momeni, E. Khademi, and Sh. Kazemi: Mater. Sci. Eng. B, 2021, vol. 263, p. 114813.10.1016/j.mseb.2020.114813 ↗
41. C.I. Chang, C.J. Lee, and J.C. Huang: Scripta Mater., 2004, vol. 51, pp. 509–14.10.1016/j.scriptamat.2004.05.043 ↗
42. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Elsevier, Amsterdam, 2012.
43. A. Heidarzadeh, T. Saeid, V. Klemm, A. Chabok, and Y. Pei: Mater. Des., 2019, vol. 162, pp. 185–97.10.1016/j.matdes.2018.11.050 ↗
44. G.R. Cui, Z.Y. Ma, and S.X. Li: Acta Mater., 2009, vol. 57, pp. 5718–29.10.1016/j.actamat.2009.07.065 ↗
45. M. SarvghadMoghaddam, R. Parvizi, M. Haddad-Sabzevar, and A. Davoodi: Mater. Design, 2011, vol. 32, pp. 2749–55.10.1016/j.matdes.2011.01.015 ↗
46. R.P. Mahto, C. Gupta, M. Kinjawadekar, A. Meena, and S.K. Pal: J. Manuf. Process., 2019, vol. 38, pp. 370–86.10.1016/j.jmapro.2019.01.028 ↗
47. N. Xu, R. Ueji, Y. Morisada, and H. Fujii, In Proceedings of the 1st International Joint Symposium on Joining and Welding, ed. Hidetoshi Fujii (Woodhead Publishing: 2013), pp 169–72.10.1533/978-1-78242-164-1.169 ↗