Dynamic Grain Growth Driven by Subgrain Boundaries in an Interstitial-Free Steel During Deformation at 850 °C
Source abstract
Abstract
A mechanism is proposed for dynamic grain growth (DGG) by subgrain boundaries driving grain-boundary migration. This mechanism is evaluated against data from an interstitial-free steel tested in tension at 850 °C and a true-strain rate of (10-4) s(-1) and rapidly quenched to preserve microstructures evolved during deformation. Tensile tests produced steady-state flow, distinct subgrains, and rapid DGG. Static annealing alone produced static grain growth (SGG) that was much slower than DGG. Electron backscatter diffraction (EBSD) provided grain size and orientation measurements. High-resolution electron backscatter diffraction (HR-EBSD) was used to accurately measure subgrain sizes and subgrain boundary misorientations. The average grain size increased linearly with strain during DGG, but the average subgrain size remained constant during straining. The average subgrain boundary misorientation increased with strain, initially rapidly and then slowly. The dihedral angle imposed in grain boundaries by intersecting subgrain boundaries decreased with increasing subgrain boundary misorientation, which supports the proposed mechanism for DGG. The driving pressure for grain-boundary migration from subgrain boundaries is estimated to be approximately one order in magnitude greater than that from dislocation density reduction under the conditions examined.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (81)
Show source-provided references
1. J.G. Byrne: Recovery, Recrystallization, and Grain Growth, The Macmillan Company, New York, 1965.
2. M.A. Clark and T.H. Alden: Acta Metall., 1973, vol. 21(9), pp. 1195–1206.10.1016/0001-6160(73)90160-0 ↗
3. O.N. Senkov and M.M. Myshlyaev: Acta Metall., 1986, vol. 34(1), pp. 97–106.10.1016/0001-6160(86)90236-1 ↗
4. D.S. Wilkinson and C.H. Cáceres: Acta Metall., 1984, vol. 32(9), pp. 1335–45.10.1016/0001-6160(84)90079-8 ↗
5. M.K. Rabinovich and V.G. Trifonov: Acta Mater., 1996, vol. 44(5), pp. 2073–78.10.1016/1359-6454(95)00263-4 ↗
6. B.-N. Kim, K. Hiraga, Y. Sakka, and B.-W. Ahn: Acta Mater., 1999, vol. 47(12), pp. 3433–39.10.1016/S1359-6454(99)00201-3 ↗
7. P.S. Bate, K.B. Hyde, S.A. Court, and F.J. Humphreys: Mater. Sci. Forum., 2004, vol. 447-448, pp. 61–66.10.4028/www.scientific.net/MSF.447-448.61 ↗
8. K.B. Hyde and P.S. Bate: Acta Mater., 2005, vol. 53(16), pp. 4313–21.10.1016/j.actamat.2005.05.029 ↗
9. O.V. Rofman and P.S. Bate: Acta Mater., 2010, vol. 58(7), pp. 2527–34.10.1016/j.actamat.2009.12.039 ↗
10. J.R. Ciulik and E.M. Taleff: Scr. Mater., 2009, vol. 61(10), pp. 895–98.10.1016/j.scriptamat.2009.07.021 ↗
11. N.A. Pedrazas, T.E. Buchheit, E.A. Holm, and E.M. Taleff: Mater. Sci. Eng., A, 2013, vol. 610, pp. 76–84.10.1016/j.msea.2014.05.031 ↗
12. D.L. Worthington, N.A. Pedrazas, and P.J. Noell, E.M. Taleff: Metall. Mater. Trans. A, 2013, vol. 44(11), pp. 5025–38.10.1007/s11661-013-1865-x ↗
13. P.J. Noell and E.M. Taleff: JOM, 2015, vol. 67(11), pp. 2642–45.10.1007/s11837-015-1592-4 ↗
14. P.J. Noell, D.L. Worthington, and E.M. Taleff: Metall. Mater. Trans. A, 2015, vol. 46(12), pp. 5709–18.10.1007/s11661-015-3188-6 ↗
15. P.J. Noell and E.M. Taleff: Metall. Mater. Trans. A, 2016, vol. 47(10), pp. 5023–36.10.1007/s11661-016-3644-y ↗
16. P.J. Noell, D.L. Worthington, and E.M. Taleff: Mater. Sci. Eng., A, 2017, vol. 692, pp. 24–34.10.1016/j.msea.2017.03.021 ↗
17. P.J. Noell and E.M. Taleff: Metall. Mater. Trans. A, 2019, vol. 50A(10), pp. 4608–19.10.1007/s11661-019-05370-2 ↗
18. R.E. Rupp, P.J. Noell, and E.M. Taleff: Metall. Mater. Trans. A, 2020, vol. 51A(12), pp. 6167–83.10.1007/s11661-020-06014-6 ↗
19. J. Humphreys, G.S. Rohrer, and A. Rollet: Recrystallization and Related Annealing Phenomena, 3rd ed., Elsevier, Cambridge, MA, 2017.
20. G. Gottstein and L.S. Shvindlerman: Grain Boundary Migration in Metals, CRC Press, Boca Raton, FL, 2010.
21. A. Bhattacharya, Y.-F. Shen, C.M. Hefferan, S.F. Li, J. Lind, R.M. Suter, C.E. Krill, and G.S. Rohrer: Science, 2021, vol. 374(6564), pp. 189–93.10.1126/science.abj3210 ↗
22. R.C. Gifkins: Trans. Metall. Soc. AIME, 1959, vol. 215, pp. 1015–22.
23. P.S. Bate: Acta Mater., 2001, vol. 49(8), pp. 1453–61.10.1016/S1359-6454(01)00033-7 ↗
24. Y. Onuki, R. Hongo, K. Okayasu, and H. Fukutomi: Acta Mater., 2013, vol. 61, pp. 1294–1302.10.1016/j.actamat.2012.11.007 ↗
25. C.R. Barrett, W.D. Nix, and O.D. Sherby: ASM Trans. Q., 1966, vol. 59(1), pp. 3–15.
26. O.D. Sherby and P.M. Burke: Prog. Mater. Sci., 1968, vol. 13, pp. 325–90.10.1016/0079-6425(68)90024-8 ↗
27. J.E. Bird, A.K. Mukherjee, and J.E. Dorn: in D.G. Brandon and A. Rosen, eds., Proceedings of the International Conference on Quantitative Relation Between Properties and Microstructure, Israel Universities Press, Haifa, Israel, 1969, pp. 255–42.
28. S. Karashima, T. Iikubo, and H. Oikawa: Trans. Jpn. Inst. Met., 1972, vol. 13(3), pp. 176–81.10.2320/matertrans1960.13.176 ↗
29. S.F. Exell and D.H. Warrington: Philos. Mag., 1972, vol. 26(5), pp. 1121–36.10.1080/14786437208227368 ↗
30. R.G. Stang, W.D. Nix, and C.R. Barrett: Metall. Trans. A, 1975, vol. 6A, pp. 2065–17.10.1007/BF03161832 ↗
31. M.E. Kassner and M.E. McMahon: Metall. Trans. A, 1987, vol. 18(5), pp. 835–46.
32. A. Einstein: Ann. Phys., 1905, vol. 322(8), pp. 549–60.10.1002/andp.19053220806 ↗
33. W. Sutherland: Philos. Mag., 1905, vol. 9(54), pp. 781–85.10.1080/14786440509463331 ↗
34. M. von Smoluchowski: Ann. Phys., 1906, vol. 326(14), pp. 756–80.10.1002/andp.19063261405 ↗
35. M. Winning, G. Gottstein, and L.S. Shvindlerman: Acta Mater., 2001, vol. 49(2), pp. 211–19.10.1016/S1359-6454(00)00321-9 ↗
36. M. Winning, G. Gottstein, and L.S. Shvindlerman: Mater. Sci. Eng., A, 2001, vol. 317(1–2), pp. 17–20.10.1016/S0921-5093(01)01193-5 ↗
37. J.W. Cahn and J.E. Taylor: Acta Mater., 2004, vol. 52(16), pp. 4887–98.10.1016/j.actamat.2004.02.048 ↗
38. J.W. Cahn, Y. Mishin, and A. Suzuku: Acta Mater., 2006, vol. 54, pp. 4953–75.10.1016/j.actamat.2006.08.004 ↗
39. J. Han, S.L. Thomas, and D.J. Srolovitz: Prog. Mater. Sci., 2018, vol. 98, pp. 386–476.10.1016/j.pmatsci.2018.05.004 ↗
40. J. Weertman and J.R. Weertman: Elementary Dislocation Theory, Macmillan, New York, 1964.
41. J.P. Hirth and J. Lothe: Theory of Dislocations, Wiley, New York, 2nd ed., 1982.
42. D. Hull and D.J. Bacon: Introduction to Dislocations, 5th ed., Elsevier/Butterworth-Hienemann, Burlington, MA, 2011.
43. W.R. Cannon and O.D. Sherby: Metall. Trans., 1970, vol. 1(4), pp. 1030–32.10.1007/BF02811789 ↗
44. P. Yavari, F.A. Mohamed, and T.G. Langdon: Acta Metall., 1981, vol. 29(8), pp. 1495–1507.10.1016/0001-6160(81)90184-X ↗
45. W. Shockley and W.T. Read: Phys. Rev., 1949, vol. 75, pp. 692.10.1103/PhysRev.75.692 ↗
46. W.T. Read and W. Shockley: Phys. Rev., 1950, vol. 78(3), pp. 275–89.10.1103/PhysRev.78.275 ↗
47. W. Köster: Z. Metallkd., 1948, vol. 39, pp. 1–9.
48. T.J. Bennett, IV: Master’s thesis, The University of Texas at Austin, 2022.
49. MTEX documentation, https://mtex-toolbox.github.io/Documentation.html, 2023.
50. MathWorks Inc.: Matlab, version R2022a, 2022.
51. R. Bergmann, R.H. Chan, R. Hielscher, J. Persch, and G. Steidl: Inverse Prob. Imaging, 2016, vol. 10(2), pp. 281–304.
52. S.A. Saltykov: Stereometric Metallurgy, vol. 2, 2nd ed., Armed Services Technical Information Agency, Arlington, VA, 1961.
53. ASTM International: Standard Designation E112–13, ASTM International, West Conshohocken, PA, 2013.
54. A.J. Wilkinson, G. Meaden, and D.J. Dingley: Ultramicroscopy, 2006, vol. 106(4), pp. 307–13.10.1016/j.ultramic.2005.10.001 ↗
55. OpenXY, https://github.com/BYU-MicrostructureOfMaterials/OpenXY, 2023.
56. G.I. Taylor: J. Inst. Met., 1938, vol. 62(1), pp. 307–24.
57. D.N. Joanes and C.A. Gill: J. R. Stat. Soc. Ser. D), 1998, vol. 47(1), pp. 183–89.10.1111/1467-9884.00122 ↗
58. J. Lin and O.D. Sherby: Res Mech., 1981, vol. 2(4), pp. 251–93.
59. O.D. Sherby, A.K. Miller, and M.E. Kassner: Met. Forum, 1981, vol. 4(1–2), pp. 53–56.
60. O.D. Sherby, R.H. Klundt, and A.K. Miller: Metall. Trans. A, 1977, vol. 8A(6), pp. 843–50.
61. S.O. Robinson, C.M. Young, and O.D. Sherby: J. Mater. Sci., 1974, vol. 9(2), pp. 341–43.10.1007/BF00550963 ↗
62. C.M. Young and O.D. Sherby: J. Iron Steel Inst., London, 1973, vol. 211(9), pp. 640–47.
63. O.D. Sherby and J. Wadsworth: Prog. Mater. Sci., 1989, vol. 33, pp. 169–221.10.1016/0079-6425(89)90004-2 ↗
64. W.C. Lenthe, S. Singh, and M. De Graef: Ultramicroscopy, 2019, vol. 207, pp. 112841.10.1016/j.ultramic.2019.112841 ↗
65. S. Singh, F. Ram, and M. De Graef: Microsc. Microanal., 2017, vol. 23(S1), pp. 212–13.10.1017/S143192761700174X ↗
66. S.F. Subramanian, M. Prikryl, B.D. Gaulin, D.D. Clifford, S. Benincasa, and I. O’Reilly: ISIJ Int., 1994, vol. 34(1), pp. 61–69.10.2355/isijinternational.34.61 ↗
67. T.A. Roth: Mater. Sci. Eng., 1975, vol. 18, pp. 183–92.10.1016/0025-5416(75)90168-8 ↗
68. E.D. Hondros: Proc. R. S. A, 1965, vol. 286(1407), pp. 479–98.10.1098/rspa.1965.0158 ↗
69. A.T. Price, H. Holl, and A.P. Greenough: Acta Metall., 1964, vol. 12(1), pp. 49–58.10.1016/0001-6160(64)90053-7 ↗
70. L.E. Murr: Interfacial Phenomena in Metals and Alloys, Addison-Wesley Publishing Company, Reading, MA, 1975.
71. E.D. Hondros and L.E.H. Stuart: Philos. Mag., 1968, vol. 17(148), pp. 711–27.10.1080/14786436808223024 ↗
72. A. Jaatinen, C.V. Achim, K.R. Elder, and T. Ala-Nissila: Technische Mechanik, 2010, vol. 30(1–3), pp. 169–76.
73. S. Ratanaphan, D.L. Olmsted, V.V. Bulatov, E.A. Holm, A.D. Rollett, and G.S. Rohrer: Acta Mater., 2015, vol. 88, pp. 346–54.10.1016/j.actamat.2015.01.069 ↗
74. J. Wang, G.K.H. Madsen, and R. Drautz: Grain boundaries in BCC-Fe: Modell. Simul. Mater. Sci. Eng., 2018, vol. 26, pp. 025008.10.1088/1361-651X/aa9f81 ↗
75. C.G. Dunn and F. Lionetti: Trans. AIME, 1949, vol. 1(2), pp. 125–32.
76. C.G. Dunn, F.W. Daniels, and M.J. Bolton: Trans. AIME, 1950, vol. 188, pp. 1245–48.
77. H.J. Frost and M.F. Ashby: Deformation-Mechanism Maps, The Plasticity and Creep of Metals and Ceramics, Pergamon Press Inc., New York, NY, 1982.
78. J.P. Butler and J.A. Reeds: SIAM J. Appl. Math., 1987, vol. 47(3), pp. 670–77.
79. J.A. Reeds and J.P. Butler: SIAM J. Appl. Math., 1987, vol. 47(3), pp. 678–87.
80. B.C. Carlson: Numer. Math., 1979, vol. 33(1), pp. 1–16.10.1007/BF01396491 ↗
81. B.C. Carlson and E.M. Notis: ACM Trans. Math. Software, 1981, vol. 7(3), pp. 398–403.10.1145/355958.355970 ↗